Jump to content


Lakes-style Chopped Deuce 5-window - Completed


  • You cannot reply to this topic
66 replies to this topic

#61 Bernard Kron

Bernard Kron

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 2,709 posts
  • Location:Seattle, WA
  • Full Name:Bernard Kron

Posted 16 November 2012 - 07:20 AM

Thanks guys!

As I finish up this build here are some final details.

One of the interesting things I learned while working on this car was something about the Buick Nailhead V-8. Apparently if you check out the parts numbers for the heads on this motor you will see the same number for both the left and right head. The two heads are identical. In fact they are symmetric front to rear and side to side. They have water intake/exit ports on both ends, too. So you simply attach either a plug or a connector to the appropriate hole. As is common practice on lakes cars I omitted a radiator. Radiators generate an enormous amount of drag with the air passing through them. Instead LSR style racers equip the cars with a large coolant tank loaded with cold water in a sufficient amount to keep the motor at acceptable temperature for the time the car will be running. As mentioned earlier, on my car I “imagineered” it to have the coolant tank in the rear of the car. So when it came time to rigging up the coolant lines I simply ran rearward facing pipes off the rear of the heads.

Of course, with no radiator there is no need for a grill, allowing for a blank panel. In this case I used transparent red “plexiglas” (actually acetate sheet) as also used in the windows. Again, this was a common practice back in the day, and allows for a “peek-a-boo” look at the front of the motor.

As I button this car up I have fabricated the steering system for this car from styrene rod and strip. In the composite photo below I’ve included a detail shot of the steering linkage, along with shots of the coolant pipes and the see-through grill panel. I will mount the moon discs to the wheels at the very end to protect the metalizer paint from too much handling. In the shot of the back side of the motor you can also see where I had to cut away the back of the bell housing to clear the firewall and kick panel. Modeling is a world of illusion and this project is no exception!

Thanx for lookin’,
B.

Posted Image

#62 Dr. Cranky

Dr. Cranky

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 15,421 posts
  • Location:Transylvania, Florida
  • Full Name:Virgil "Doctor Cranky" Suarez

Posted 16 November 2012 - 08:27 AM

Lordy, I love that see through grill. Nice touches throughout.

#63 Bernard Kron

Bernard Kron

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 2,709 posts
  • Location:Seattle, WA
  • Full Name:Bernard Kron

Posted 16 November 2012 - 03:35 PM

Thanks Cranky!

This project is now complete. Thanks to everyone who followed along. The beauty shots can be found in Under Glass here: http://www.modelcars...showtopic=66573 In the meantime here’s a teaser shot…

Thanx for lookin’,
B.

Posted Image

Edited by Bernard Kron, 16 November 2012 - 03:35 PM.


#64 wilderness1989

wilderness1989

    MCM Regular

  • Members
  • PipPipPip
  • 53 posts
  • Location:Charleston, IL
  • Full Name:John Gray

Posted 23 June 2013 - 11:49 AM

Extremely COOL!!!!!!  Thank you!!!!!!!!!!!!!!!!!!!!!!!



#65 PappyD340

PappyD340

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 5,159 posts
  • Location:High Point, NC
  • Full Name:Larry Dailey

Posted 23 June 2013 - 02:35 PM

VERY VERY NICE!! :D 



#66 Bernard Kron

Bernard Kron

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 2,709 posts
  • Location:Seattle, WA
  • Full Name:Bernard Kron

Posted 15 July 2013 - 07:53 AM

Thanx guys, both for the "rediscovery" and the compliments! I'm glad you like it. B)  :)



#67 Ace-Garageguy

Ace-Garageguy

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 7,617 posts
  • Location:Down two, then left.
  • Full Name:Bill Engwer

Posted 15 July 2013 - 12:06 PM

Bernard, this one's always fun to look at. :D