Jump to content


1958 PLYMOUTH - - - FINISHED


  • You cannot reply to this topic
56 replies to this topic

#1 Ramfins59

Ramfins59

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 3,085 posts
  • Location:Cranberry township pa
  • Full Name:Richard Manson

Posted 21 February 2013 - 07:39 PM

Hello all.  I fought with it a bit at final assembly, but it's done...!!!  A few notes to anyone else who is going to build this kit;

 

- - DON'T attach the front and rear pans until AFTER the chassis / interior assembly is installed (like the instructions say).  I made the mistake of attaching them beforehand thinking it would look better when all       

     painted in one shot.  It doesn't matter because the seams where the pans attach to the body are covered by the bumpers anyway.

- - Prepare for a LOT of cursing, swearing and sweating when fitting the completed engine / chassis / interior assembly into the body.  IT IS A VERY TIGHT FIT...!!!  You'll have to gingerly spread the body sides   in order to get the rear inner fenderwells to slide down.

- - Open up the locating holes a little bigger for the bumpers, the front fender ornaments, the mirrors and the antenna.  After a couple of coats of primer, paint and clearcoat the holes get very tight for the pegs to fit.

- - Slightly enlarge the locating holes for the windshield locating pins in the interior.  It's such a tight fit that the glass literally snaps into place and the area around the locating holes cracks a little.  Fortunately the

    cracks didn't travel into the windshield area.  I'm suggesting that YOU slightly enlarge the locating holes just to be on the safe side so the glass doesn't crack on you.

- - Glue the firewall into the body and not to the interior assembly as the instructions say.  You'll get a better fit to the engine compartment that way.

- - Make sure that the radiator and radiator support assembly are seated as low as you can get them or the hood won't close right (like mine..!!)

 

I think those are all the major points of difficulty that everyone should be aware of, along with the exhaust system issues that I previously pointed out in my WIP thread for this model.

 

Now, without further ado, let me introduce you to Christine's sister......   CHRISTINA....The GOOD 1958 Plymouth......

 

 

COMPLETEDPLYMOUTHSIDE1024x739_zps82a2d4e

 

 

COMPLETEDPLYMOUTH11024x668_zps4d54b4b5.j

 

 

COMPLETEDPLYMOUTHREAR1024x763_zps0961e30

 

 

and here's a shot of the engine compartment

 

 

PLYMOUTHENGINECOMPARTMENT1024x761_zpsfaa

 

 

Thanks to all for looking in at this.

 



#2 Villain

Villain

    MCM Regular

  • Members
  • PipPipPip
  • 72 posts
  • Location:Dayton NV
  • Full Name:Matt Fischer

Posted 21 February 2013 - 07:50 PM

Looks Good! Nice Job!!!



#3 slusher

slusher

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 15,337 posts
  • Location:tennessee
  • Full Name:carl slusher

Posted 21 February 2013 - 08:44 PM

Rich, another great looking build. Nice Foil work also. Excellent deetail...



#4 ChrisR

ChrisR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 2,484 posts
  • Location:South Africa
  • Full Name:Chris Roos

Posted 21 February 2013 - 10:33 PM

Nice engine detail and a great model.



#5 jeffs396

jeffs396

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 3,186 posts
  • Location:NE Ohio
  • Full Name:Jeff

Posted 22 February 2013 - 01:49 AM

Great job Rich!!!

 

Christina...cool! B)

 

Hope to see it on the table at Castle Shannon in a few weeks!



#6 cobraman

cobraman

    Crazy 'bout Cobras!

  • Members
  • PipPipPipPipPipPip
  • 10,455 posts
  • Location:Arizona
  • Full Name:Ray Kurn

Posted 22 February 2013 - 03:00 AM

Looks great ! Very nice work.



#7 Bad Apple

Bad Apple

    MCM Friend

  • Members
  • PipPipPipPip
  • 127 posts
  • Location:Central PA
  • Full Name:Kevin Sherman

Posted 22 February 2013 - 03:02 AM

Looks great! I just ordered this kit this morning.



#8 Nitro Neil

Nitro Neil

    MCM Avid Poster

  • Members
  • PipPipPipPipPip
  • 375 posts
  • Location:New Hampshire
  • Full Name:Neil Van Zile, Jr.

Posted 22 February 2013 - 03:20 AM

Very nice work Rich.



#9 pa3de8

pa3de8

    MCM Regular

  • Members
  • PipPipPip
  • 81 posts
  • Location:North Carolina
  • Full Name:Scott Banzaca

Posted 22 February 2013 - 03:27 AM

Gotta say that when I saw the under hood shot I couldn't believe it wasn't real. Great detail there. Hopefully when I am finished with my 41 Ford Woody I can do the same. The whole build looks great Rich!



#10 Paul H

Paul H

    MCM Regular

  • Members
  • PipPipPip
  • 93 posts
  • Location:Emsworth, UK
  • Full Name:Paul Harker

Posted 22 February 2013 - 03:39 AM

Liking that a lot, & great to see one that isn't in Christine colours!  These are probably one of my favourite late '50s designs, as they are so sleek and aggressive.

 

Edited for spelling....


Edited by Paul H, 22 February 2013 - 04:39 AM.


#11 johnbuzzed

johnbuzzed

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,267 posts
  • Location:Indian Land, SC
  • Full Name:John "the Buzzard" Buzzerio

Posted 22 February 2013 - 04:15 AM

I can't see it now but I'll check it over the weekend from home.  Thanks for the building tips- I have one of these on my shelf with plans on paper for it.



#12 Ace-Garageguy

Ace-Garageguy

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 7,598 posts
  • Location:Down two, then left.
  • Full Name:Bill Engwer

Posted 22 February 2013 - 04:26 AM

Fine looking model. All your BMF and extra underhood detail really bring it to life.



#13 Harry P.

Harry P.

    MCM Ohana

  • Administrators
  • PipPipPipPipPipPip
  • 22,790 posts
  • Location:NW suburban Chicago
  • Full Name:A mere layman...

Posted 22 February 2013 - 04:37 AM

I like it! I think you did a great job on it.



#14 Yahshu

Yahshu

    MCM Avid Poster

  • Members
  • PipPipPipPipPip
  • 458 posts
  • Location:Australia
  • Full Name:Phil de la Cour

Posted 22 February 2013 - 04:43 AM

She's real nice. :D



#15 Guest_Johnny_*

Guest_Johnny_*
  • Guests

Posted 22 February 2013 - 07:05 AM

Love it! Even with it's issues it is still a good looking kit when done right! B)



#16 Davewilly

Davewilly

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,856 posts
  • Location:Surprise, Arizona
  • Full Name:Dave Wilmore

Posted 22 February 2013 - 07:16 AM

Looks great!  Like the White look  Most of them I have ever seen (models) are red or black..



#17 MAGNUM4342

MAGNUM4342

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,285 posts
  • Location:Parkersburg
  • Full Name:Kevin White

Posted 22 February 2013 - 07:26 AM

For having fought you so hard it sure looks as if you wrestled it to submission. Well done but...what? No interior pics? :D 



#18 MikeyB08

MikeyB08

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 502 posts
  • Location:Radford, Virginia
  • Full Name:James Basham

Posted 22 February 2013 - 08:02 AM

Looking Good!!! Just a little tip about the body being a tight fit, next time take a soda can and cut the top and bottom off. Then cut the remaining can in half so you have 2 slates. Use the slates to help aide the body down so it doesnt get caught on anything. Worth a shot.

#19 crazyjim

crazyjim

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 11,876 posts
  • Location:Citrus Springs, FL

Posted 22 February 2013 - 08:18 AM

Marvelous build, Rich.  Terrific detail and SHINY :) :) :)



#20 Models by Bear

Models by Bear

    MCM Avid Poster

  • Members
  • PipPipPipPipPip
  • 299 posts
  • Location:Indiana
  • Full Name:Chris Bognar

Posted 22 February 2013 - 08:36 AM

Wow! that's a lot of foil work ,Awesome job on this one