allecb Posted March 13, 2013 Share Posted March 13, 2013 so i was browsing the forum because my last model i had issues with glue and i learned that elmers glue is great for putting windshields in, and not getting glue everywhere. also, the whole toothpick method is an amazing idea as well. but what about headlights or tail lights? theres nothing worse than having a model look amazing, then you go to glue on the headlights, and now they are all fogged up and look fake and horrible. any tips for these? would elmers glue work the same? i was thinking about making using some of my testors gloss coat/clear gloss..would that work like a glue? Quote Link to comment Share on other sites More sharing options...
Ace-Garageguy Posted March 13, 2013 Share Posted March 13, 2013 (edited) Yes, any of the white PVA (polyvinyl acetate) glues will work on lights just like on windows. That's what you need, and they're idiot-proof. I use Microscale's Micro Kristal Klear. No bull. Edited March 13, 2013 by Ace-Garageguy Quote Link to comment Share on other sites More sharing options...
Skydime Posted March 13, 2013 Share Posted March 13, 2013 Anyone ever try the clear version of Elmer's School Glue? I know that white works pretty well but, I was thinking that the clear may work even better. Quote Link to comment Share on other sites More sharing options...
Ace-Garageguy Posted March 13, 2013 Share Posted March 13, 2013 (edited) Never bothered, but it's sure worth a try. MKK works perfectly every time, dries entirely clear and invisible if you don't slather it on. Edited March 13, 2013 by Ace-Garageguy Quote Link to comment Share on other sites More sharing options...
Mike_G Posted March 13, 2013 Share Posted March 13, 2013 I use the tiniest bit of 5-minute epoxy. Quote Link to comment Share on other sites More sharing options...
Ramfins59 Posted March 13, 2013 Share Posted March 13, 2013 I've been using Model Master clear enamel to glue in headlight and taillight lenses, along with any turn signal lenses in some kits. I apply it with a toothpick around the edges of the bezels. If you've ever fought with a paint jar lid to get it off, it's proof that dried paint makes an excellent glue. Quote Link to comment Share on other sites More sharing options...
Blown03SVT Posted March 13, 2013 Share Posted March 13, 2013 If you've ever fought with a paint jar lid to get it off, it's proof that dried paint makes an excellent glue. Excellent point! Quote Link to comment Share on other sites More sharing options...
crazyjim Posted March 14, 2013 Share Posted March 14, 2013 I'm a firm believer in Micro Krystal Klear for glass, headlights, and taillights. However, I have a bottle of canopy glue that's used by the model airplane guys that I plan to try out. Quote Link to comment Share on other sites More sharing options...
935k3 Posted March 14, 2013 Share Posted March 14, 2013 (edited) Try one of these to hold the light or lens; Then use a tooth pick and apply this(the strongest white glue): Edited March 14, 2013 by 935k3 Quote Link to comment Share on other sites More sharing options...
southpier Posted March 14, 2013 Share Posted March 14, 2013 as one applies these lenses, how do you keep the lines parallel to the ground and each other? Quote Link to comment Share on other sites More sharing options...
Captain Obvious Posted March 18, 2013 Share Posted March 18, 2013 I keep forgetting to try clear enamel, but I have had some success using Future floor polish for light lenses. Don't think it's quite strong enough for glass though. as one applies these lenses, how do you keep the lines parallel to the ground and each other? I'll assume you mean the molded-in lines on a headlight lens? I just eyeball it as close as possible when installing them, then rotate as needed with a toothpick or tip of a hobby blade before the adhesive sets. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.