Biffo Posted April 24, 2015 Share Posted April 24, 2015 (edited) Don't know how long it will take but thought i'd start another model(currently haves s/m dust, frank iaconio firebird, glidden thunderbird and Tommy ivo rail underway!) So i acquired a 7/11 mustang f/c (started/badly) off ebay, stripped the body and disassembled the chassis, opened roof hatch, and from few reference photos i have found i noticed the 7/11 car spoiler is wrong, the car i want to build (early 1985? john lombardo driven) has longer and lower on the body rear spill/spoiler plates so i started re-cutting the body to fit more accurate plates. Struggling to get good reference info so any help with (a) paint colour ? ( 8 or 16 plug heads? and ©what wheel pattern? Edited May 15, 2015 by Biffo Quote Link to comment Share on other sites More sharing options...
iBorg Posted May 2, 2015 Share Posted May 2, 2015 There was a feature on this car in Peterson's Drag Racing magazine had a feature on it when the car was current. I'm sorry I don't have access to my copy now or I'd help you out. A few things about this car, it changed greatly. It started with plain Blue Max logo's, then had Schlitz and finally Old Milwaukee. A couple of things I recognize from the various photos I have. The car sit very low to the ground. The rocker panels were level to the ground. The rear spoiler was about twice the length of the Billy Myer piece. If other cars of the era was running a dual plug head, the Blue Max had dual plugs. Quote Link to comment Share on other sites More sharing options...
Biffo Posted May 5, 2015 Author Share Posted May 5, 2015 Got some more done, built up the ends of the original spoiler with car body filler and sanded back, attached larger spoiler, made from a piece of plasticard which i rolled a bit of a curve into, and then fixed a narrower piece underneath, also started engine (stripping and repairing previously assembled one) photo shows repairs to cylinder head underway. Thanks for the info Mike and i think your right body needs to be lowered (and header cut outs made), but i think the heads will be single plug (seen short pit video clip showing one mag) i think it they went to dual plugs later in the year when Raymond Beadle quit as driver !!? Quote Link to comment Share on other sites More sharing options...
Biffo Posted May 6, 2015 Author Share Posted May 6, 2015 More progress made, have found body up photo of the car at Don Garlits museum, which is great help and confirms things like no computer, 8 plug heads, blue plug wires etc, as far as build goes i have attached salvaged/repaired heads to the block and made some adjustable rear axle mounts, (cut from an old scrap chassis) attached to plasticard, which will allow me to adjust the rear ride height at a later stage, see 2nd photo. Quote Link to comment Share on other sites More sharing options...
Biffo Posted May 15, 2015 Author Share Posted May 15, 2015 (edited) Heres the Engine, (gone for single plug heads, as in reference photo of car at Don Garlits Museum) i have block, heads, rocker covers and manifold done, working on manifold injector block now,,, Edited May 15, 2015 by Biffo Quote Link to comment Share on other sites More sharing options...
iBorg Posted May 15, 2015 Share Posted May 15, 2015 Can you post a link to the Don Garlits Museum photo? Quote Link to comment Share on other sites More sharing options...
Biffo Posted May 16, 2015 Author Share Posted May 16, 2015 Sorry Mike cannot find it again now, but here's the version i have copied, note 8 plug heads, no header cut outs,,, P,S. just noticed your e mail, check your in box, Quote Link to comment Share on other sites More sharing options...
Biffo Posted May 28, 2015 Author Share Posted May 28, 2015 (edited) Have made progress with engine, started to work on scratch building magneto (first photo),,, and barrel valve (second photo),,, puke tank and oil filter housing finished (third) ,,,, ,,,, manifold, and blower injector lines made and fitted (fourth). Cannot find a blower belt pullley set that i am happy with, looking through parts bin and have a few in mind but all seem to have a very thick belt moulding,,,, ANYONE KNOW OF A GOOD RESIN SET? Edited May 28, 2015 by Biffo Quote Link to comment Share on other sites More sharing options...
snacktruck67 Posted May 28, 2015 Share Posted May 28, 2015 I got a set from Arrowhead Aluminum Accessories. Really good stuff. Quote Link to comment Share on other sites More sharing options...
Sledsel Posted June 16, 2015 Share Posted June 16, 2015 Very cool build. Wanting to build the same car so I am watching this one Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.