Scale-Master Posted February 20, 2015 Author Share Posted February 20, 2015 I cut a hole to match the one I cut into the hood of the real car. And cemented and faired the scoop into the hood. Quote Link to comment Share on other sites More sharing options...
Belugawrx Posted February 20, 2015 Share Posted February 20, 2015 (edited) Looking at the photos I'm going to put this one right at 1982, a few months before it got totaled. It's death stemmed from the lower right ball joint going out and the control arm went through the tire, fortunately I was just pulling out so that was all the damage. I called for a flat bed and the driver said I needed to remove the driving lights or they would be removed forcibly, since I was only a few blocks from home I ran and got a couple wrenches. When I returned the car was in flames, a moron decided he could nurse it up the bed. Considering the control arm was embedded in the asphalt, I have no idea what logic he was using. When he tried to start it he flooded the side draft Webers fed by an electric fuel pump and then the car backfired. Dumass left the key on so the pump fed the fire plenty of gas. I was told flames came through the defroster vents and hit the idiot in the face. Served him right. I sued him won the case and bought the '73 Camaro with a few hundred left over. Whoa ! I am left speechless by the stupidity Edited February 20, 2015 by Belugawrx Quote Link to comment Share on other sites More sharing options...
Revstew Posted February 20, 2015 Share Posted February 20, 2015 Great looking build!! I am for sure going to be following this one. you just can't fix stupid unfortunately. Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted February 20, 2015 Author Share Posted February 20, 2015 As tragic as I felt the loss was at the time, the reality is I would likely never found the Camaro (that I still have) had that not happened.I learned a lot from that Vega, and I while I've wanted to make this model of it for a long time, I don't want another real one. Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted February 21, 2015 Author Share Posted February 21, 2015 I also installed a sunroof to my Vega, so I cut out a hole in the roof… Quote Link to comment Share on other sites More sharing options...
slusher Posted February 21, 2015 Share Posted February 21, 2015 Man, that hood looks awesome... Quote Link to comment Share on other sites More sharing options...
tbill Posted February 21, 2015 Share Posted February 21, 2015 hard to make a vega wagon look cool, but this is it! I too had one of these 'things' back in the day, orange with brown doors and that plaid interior. I got it near the end of it's usefull life, but it managed to get me where I needed to be Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted February 27, 2015 Author Share Posted February 27, 2015 (edited) While casting some other parts I was using dye to color the resin and came up with a near exact match to the color of the spoke section of the wheel straight from the mold. Edited February 27, 2015 by Scale-Master Quote Link to comment Share on other sites More sharing options...
Scalper Posted February 27, 2015 Share Posted February 27, 2015 Thats a perfect sunroof hole Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted February 27, 2015 Author Share Posted February 27, 2015 Thanks. I just scribed the hole with the back side of a #11 X-Acto knife after masking off the shape as a guide. The "trick" is to go slow. Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted February 27, 2015 Author Share Posted February 27, 2015 Finding tires proved to be more of a challenge. I settled on this two piece injection molded tire from a MPC Volare Road Runner with Parts Pack. I filled the tire with polyester filler and turned it down and reshaped on the lathe. Then I cut a little tread pattern into it and removed the axle post. For a curbside it should be fine especially after the side wall details are added. These are the resin parts I will detail and finish. Quote Link to comment Share on other sites More sharing options...
Revstew Posted February 27, 2015 Share Posted February 27, 2015 Wow that is great looking. Can't wait to see them detailed out. You have a lathe at home for turning these? I would like to see about getting one down the road. Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted February 28, 2015 Author Share Posted February 28, 2015 Yes, I used my lathe to turn them and my mill to add the tread, such as it is... Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted February 28, 2015 Author Share Posted February 28, 2015 Digging around last night I found a piece of aluminum pipe in my metal stockpile, it had a slightly larger O.D. and a smaller I.D. that what would work for the outer rim for the wheels. So I machined up a set and also modified the wheels I cast to accept it. The aluminum is something from the plumbing supply section of a hardware store. Not too soft, but also not heat treated and very gummy to cut, but it was so close to the size I needed it was worth it to use. This is the first one I test made before doing the set of four I’ll actually use. Quote Link to comment Share on other sites More sharing options...
slusher Posted February 28, 2015 Share Posted February 28, 2015 Wheel and tire looks impressive.. Quote Link to comment Share on other sites More sharing options...
cobraman Posted March 1, 2015 Share Posted March 1, 2015 Looks great ! Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted March 5, 2015 Author Share Posted March 5, 2015 Thanks Ray. I made decals for the sidewalls to match the tires I had on my car. Quote Link to comment Share on other sites More sharing options...
cobraman Posted March 6, 2015 Share Posted March 6, 2015 Tires look great ! Quote Link to comment Share on other sites More sharing options...
slusher Posted March 6, 2015 Share Posted March 6, 2015 Great looking decals Fred.. Quote Link to comment Share on other sites More sharing options...
crazyrichard Posted March 6, 2015 Share Posted March 6, 2015 cool !! Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted March 6, 2015 Author Share Posted March 6, 2015 Great looking decals Fred.. Who's Fred? Quote Link to comment Share on other sites More sharing options...
Revstew Posted March 6, 2015 Share Posted March 6, 2015 Wow just amazing looking tires!! Quote Link to comment Share on other sites More sharing options...
crazyrichard Posted March 6, 2015 Share Posted March 6, 2015 Who's Fred? Quote Link to comment Share on other sites More sharing options...
Dragfreak Posted March 7, 2015 Share Posted March 7, 2015 (edited) Very cool project, My first car was a '71 vega panel express, and my current racecar is a '71 vega panel express. I'll be following along closely. Edited March 7, 2015 by Dragfreak Quote Link to comment Share on other sites More sharing options...
Bill Edman Posted March 7, 2015 Share Posted March 7, 2015 cool project wish i could find one of these bodies Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.