nirvana_m24 Posted May 16, 2009 Share Posted May 16, 2009 Hello. I'm new to the forum and could use any help anyone can offer. I'll appreciate any help you can offer.Im working on the revell integra type r model and I like the way they look without the spoiler.I was wondering what to use to fill in the holes that are for the spoiler.Do you I just use bondo or something?Any help will be helpful.Thank you Quote Link to comment Share on other sites More sharing options...
Harry P. Posted May 16, 2009 Share Posted May 16, 2009 Welcome aboard! As far as filling the spoiler holes, there are a couple ways you can go. 1. Rough up the area around the holes with some coarse sandpaper or a Dremel tool with a rough grit sanding drum bit. Then fill the holes with either some 5-minute epoxy or Bondo (or another brand of 2-part filler), and sand smooth when hardened. Do NOT use "spot putty" or "model putty", as they will shrink over time and your filled holes will become indentations (usually after you've finished and painted the model!) 2. Another way to go is to hold a piece of scrap sprue over a candle flame until it softens, then pull the ends apart until you get a length of stretched sprue between the two ends. Then cut the sprue apart and jab the stretched sprue into the hole, using liquid model cement to glue the sprue into place. The liquid cement will actually fuse the sprue and the kit piece together. When the glue dries, snip off the excess and sand smooth. Quote Link to comment Share on other sites More sharing options...
FujimiLover Posted May 16, 2009 Share Posted May 16, 2009 Welcome abored. You can also try useing gap-filling CA glue. Just a tiny little dap inside the hole should do the trick. But I'd go with harry's suggestion instead. Quote Link to comment Share on other sites More sharing options...
nirvana_m24 Posted May 16, 2009 Author Share Posted May 16, 2009 (edited) Thank you for your help.I'll try the first suggestion.Can I get the epoxy or bondo at an auto store?If not where at?Thank you again. Edited May 16, 2009 by nirvana_m24 Quote Link to comment Share on other sites More sharing options...
nirvana_m24 Posted June 4, 2009 Author Share Posted June 4, 2009 Thanks again for all the help.It's my first time working with body filler bondo but as soon as I get my camera back I'll post up the pics of my project.It's almost finished.Thanks again. Quote Link to comment Share on other sites More sharing options...
blkdc2 Posted November 13, 2012 Share Posted November 13, 2012 Welcome aboard! As far as filling the spoiler holes, there are a couple ways you can go. 1. Rough up the area around the holes with some coarse sandpaper or a Dremel tool with a rough grit sanding drum bit. Then fill the holes with either some 5-minute epoxy or Bondo (or another brand of 2-part filler), and sand smooth when hardened. Do NOT use "spot putty" or "model putty", as they will shrink over time and your filled holes will become indentations (usually after you've finished and painted the model!) 2. Another way to go is to hold a piece of scrap sprue over a candle flame until it softens, then pull the ends apart until you get a length of stretched sprue between the two ends. Then cut the sprue apart and jab the stretched sprue into the hole, using liquid model cement to glue the sprue into place. The liquid cement will actually fuse the sprue and the kit piece together. When the glue dries, snip off the excess and sand smooth. I'm also working on same integra kit but 1st timer on customizing. Still working on body with a lot of customizing. I used Tamiya white putty for filling in joined parts - will this shrink after I primer and paint as you stated? Thanks in advance. New member, just picked up modeling again from a very long break. Will try to post pics of current build. Quote Link to comment Share on other sites More sharing options...
Deathgoblin Posted November 13, 2012 Share Posted November 13, 2012 I did the same thing on my F&F Toyota Supra kit. I used some thin round stock and a little superglue, cut it off flush and once it was dry sanded it smooth. It turned out pretty good. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.