Jump to content
Model Cars Magazine Forum

Hary Bare

Members
  • Posts

    29
  • Joined

  • Last visited

Previous Fields

  • Scale I Build
    1/24

Profile Information

  • Full Name
    Billy Bayer

Recent Profile Visitors

3,028 profile views

Hary Bare's Achievements

MCM Regular

MCM Regular (3/6)

  1. What a great job on this kit! Mine pales in comparison, I should try it again just because. Very nice!
  2. What an outstanding model! I truely enjoy the classic kits built to such standards. Yours are simply inspirational. Thank you for sharing!
  3. The Freightliner was my first truck too. I had a lot of questions answered on this forum and made building this model a lot less complicated. I never did weather mine or put better stacks on it but I like the way it looks and I get a lot of compliments,,,. Yours is looking really nice, enjoy the build and the finished model.
  4. Ben, I recently completed this kit. It was fun to build but I too asked a lot of questions and received tons of useful replies. About the cab, I glued small strips to the inside of the cab, about 1 inch aprt and made sure they were flat and left overnite. I put sandpaper on a piece of glass and lightly ran both haves to flatten. After piecing together I glued from the inside between the strips, rubber band them and set overnite. Removed strips and finished glueing inside. I had a nice crisp seam when dried and used spot putty to fill the seam. I used sanding sticks and blocks to clean up. It came out nice. The front axle is too wide so I found center and cut 3 3/2 from each side, drilled and pinned the axle and reglued, then cleaned up with putty. You will have to modifly the axle mounting pads to fit. Or delete the brakes and you are closer to correct. Put the grill on the frame and test fit the cab, then place your rear mounts appropriatly. At this point do youself a favor and test fit the front bumper. Towards the end of my build I found I needed to trim the frame horns and lose the mounting spots on the bumper itself to make the cab clear the bumper when tilted. To the interior tub, gently test fit. If it starts binding, start trimming until it fits easily. Then test fit the privacy curtain and tub for fit, I had to trim my curtain. The steps on each side are terrible! take your time and be carefull you use the right pieces for the correct side. I should have taken advice and bought aftermarket or sturrups. I ended up modifying mine and painting black. Exhaust pipes are too small. buy some tubing at hobby shop and replace them. I still haven't done mine. Paint? The engine is supposed to be cummins beige, rocker cover painted I guess, I painted mine. Be carefull with the air intake grill to motor, mine was finicky fit. My truck is black and gold, so I painted frame gloss black w/ flat and semi gloss black particulars. Other than that, just test fit EVERYTHING and you will be happy with your results! Lets see some pics? Enjoy.
  5. Trailer is finished. as promised here are some pics. Sorry for the pic quality, looked good on camera but dark here. Other than finding something to use for airlines, its done enough. Thanks again for all the input and suggestions. Decided not to weather it much, so many things learned on this build but I will share future builds with yas.
  6. Chuck, this is my first semi and I share the same thoughts about this kit. So many things to do different next time. I put that front plate on, no interferance but It looks like armor plate. If any interest I will post pics when trailer is finished .
  7. After a short hiatus, got back to the Freightliner. A few small things to do but here it is. Posting a couple pics. I really enjoyed this model, a real learning experience on this one. Thanks to all who gave me imput and advice as it really helped bunches. IMy next project will be a painted to match the truck.
  8. After I made my cut, I did pin the axle. If I remember right, 3/32 cut off center put me where I needed to be. I did move the spring perches also but not correctly. It was a little off center. This kit was a learning experience for me and I will have better insight on how to proceed with my next build. A fun kit with lots of basic modeling challenges but its going to turn out nice, not as well as I would have liked, certainly entertaining to view. The hardest part other than lining up the body panels, was figuring out instructions. All pieces should and will have to be test fit to ensure all corrosponding parts go together. Since I have limited knowlege of big rigs, more researsh should have been made. I didn't research much and the kit shows its flaws. Ladders are mounted along with the front bumper. That is another area that needs some trimming to fit well. I had to trim the frame horns and the mounting area on the bumper to make it visually correct and to allow the cab to tilt without interferance. It took some test fitting to get it right. Some new stacks, finish the air conditioner and put on lights and fun chrome parts. some weathering and I call it complete.
  9. Very nice! Love the paint job! Believe this will be my second big rig.
  10. Very Nice! If I hade an old beater truck laying around I would donate ,,,wait,,,I am building one LOL! Seriously, a different and excellent build!
  11. There it is as of now. Over all I am ok with this kit, I did 1/48 scale aircraft for years and had a handle on those. In the last 14 months I have done 3 automotive models and what a differance! My first was a '57 corvette gasser, its complete minus wiring and plumbing, a 1932 Chrysler Imperial Roadster, and this kit. The Chrysler was easy! LOL! Next issue to fix here is exhaust, figure out the ladders and add more pieces. I am going to attempt an air conditioning unit for the roof and some wheel flairs. The pics shown almost everything is in mock up and held in place minimally. I still have to figure out my weathering and I purchased a trailer for this kit. Going to have to decide if a generic paint on trailer or match the black and gold, Hmmm? All comments and critics are welcomed and encouraged, Sorry for the photo quality but thats the way it is. Thanks for looking.
  12. Truely a manificent build! The Gilmore museum in Hickory Corners Mi. has one and other than the paint and advertising it looks like the real bus there. Nice!
  13. Thanks for the suggestion Robert. From the muffler and guard up, a larger diameter pipe seems in order. I will take a side to the hobby shop and see what will look "right". Still debating over straight, bologna cut or maybe clackers on top? Put the steps together,,,are you kidding ?? Made sure the notches were correct per side and they just don't jive! Any alternative suggestions? These look terrible. I am not building a show quality model here but this kit is kinda cranky! Did I pick the the most finicky kit of the bunch for a first truck build lol? I will take pics sunday. Lots done since last pics. I did touch up my bleed thru tonight and the color is right and stripes are straight. installed the tanks and test fited the fenders to see how they look. slowly but not surely.
×
×
  • Create New...