Jump to content


Clear coat over Tamiya


  • You cannot reply to this topic
7 replies to this topic

#1 m408

m408

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 601 posts
  • Location:campbell, ca

Posted 22 September 2008 - 03:20 PM

Have no idea what type of paint Tamiya is, other than expensive.

What do you folks recommend for a clear coat, and how long should I wait for the paint to set before coating?

Edited by m408, 22 September 2008 - 08:10 PM.


#2 LVZ2881

LVZ2881

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,019 posts
  • Location:Las Vegas,NV, but wishing i was home in salem, oregon

Posted 22 September 2008 - 04:23 PM

Tamiya is a synthetic lacquer..any lacquer paint will work..

best option is Tamiya TS-13 clear. its good stuff, put a couple mist coats down for base, then lay down a few wet coats.it goes on very thin, like all tamiya paint, so you will need the heavier wet coats at the ends...

its best to clear over tamiya within 30 minutes or wait 30 days..
I have waited 24 hours to clear, and didnt have an issue, but have heard that was pushing it..

I have used Testors model master lacquer clear over Tamiya with mixed results. I dont think Tamiya gloss black likes anything other than Tamiya clear. but I put it over a tamiya chrome yellow base and tamiya pearl clear mid coat with great results.

duplicolor import touch up paint clear, is another option. its also lacquer, but i havent tried it over tamiya...

#3 m408

m408

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 601 posts
  • Location:campbell, ca

Posted 22 September 2008 - 08:16 PM

Tamiya is a synthetic lacquer..any lacquer paint will work..

best option is Tamiya TS-13 clear. its good stuff, put a couple mist coats down for base, then lay down a few wet coats.it goes on very thin, like all tamiya paint, so you will need the heavier wet coats at the ends...

its best to clear over tamiya within 30 minutes or wait 30 days..
I have waited 24 hours to clear, and didnt have an issue, but have heard that was pushing it..

I have used Testors model master lacquer clear over Tamiya with mixed results. I dont think Tamiya gloss black likes anything other than Tamiya clear. but I put it over a tamiya chrome yellow base and tamiya pearl clear mid coat with great results.

duplicolor import touch up paint clear, is another option. its also lacquer, but i havent tried it over tamiya...

Thanks James. Problem is that this will be a two tone paint job with a thin black stripe between the colors. Maybe just using Future might be my best bet.

#4 curt raitz

curt raitz

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,303 posts
  • Location:Hollister, CA

Posted 23 September 2008 - 04:45 PM

Milt
I've used both Tamiya Clear and Model Masters Ultra Gloss clear over Tamiya paints without any problems
If you're not worried about losing detail...Rustoleum Clear Lacquer works well also, it's a wee bit heavier...but comes in a big can

as far as a two tone paint jobs...clear coat after applying all of your color coats
this also helps knock down ridge lines between the colors
good luck

c'ya
curt

#5 Harold

Harold

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,311 posts
  • Location:Flint, Michigan
  • Full Name:Harold Palmer

Posted 24 September 2008 - 04:22 AM

I recently used Dupli-Color clear over Tamiya Black Metallic on a '97 F-150 with no ill effects. Actually, since I didn't have much left in the can, everything was basecoated with Dupli-Color Universal Black, and after laying on the Tamiya paint, I shot the lower body with Dupli-Color Desert Tan.

#6 m408

m408

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 601 posts
  • Location:campbell, ca

Posted 24 September 2008 - 08:00 AM

Thanks guys. I'll try to explain the extent of my dilemma, and my proposed plan. Your comments will be appreciated.

The kit is AMT's 34 Ford 5 window. To install the interior bucket the body must be spread. Can't do it with the fire wall glued in. Don't want to install the interior and have to mask windows etc.. for paint. So....I have painted the top section and applied Future to allow for some handling while working on the lower section. Installing windows and interior bucket. Then will finish lower section, prep, and paint.

Whacha think?

#7 moe

moe

    MCM Member

  • Members
  • PipPip
  • 12 posts

Posted 18 October 2008 - 05:03 PM

hey man i use future floor wax it works gret i mix it 2 parts wax and 1 part 90% alhocohol

#8 Zoom Zoom

Zoom Zoom

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 3,240 posts
  • Location:Tucker, Georgia

Posted 18 October 2008 - 05:47 PM

hey man i use future floor wax it works gret i mix it 2 parts wax and 1 part 90% alhocohol


Future is already so thin it runs like crazy with almost no provocation. There is no need to thin it at all to spray, if anything it needs to thicken before being sprayed. The only thing I really like about spraying Future is the lemony scent :)