Jump to content


Brute Force 71 Camaro


  • You cannot reply to this topic
213 replies to this topic

#1 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 12 December 2012 - 07:40 PM

The tape is for where all the points of measuer line is to do all mods on the sides and the hood and top. There is also some nose work will be done off the center line. There will be over 20 diffrent mods done to the body in all. 16118_4632909874542_832995353_n.jpg481468_4603057928262_1021531904_n.jpg61810_4632897434231_924069251_n.jpg

 

 

 

The tape is for where all the points of measuer line is to do all mods on the sides and the hood and top. There is also some nose work will be done off the center line. There will be over 20 diffrent mods done to the body in all.

If you was tired of seeing "Runt" in build mold here is the next one in line, "Brute Force" The body mods are now starting to be in place as I open up the vents so they can be molded into the body work



#2 Doobie

Doobie

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,201 posts
  • Location:England
  • Full Name:Dave Chivers

Posted 13 December 2012 - 01:07 AM

It looks good so what are the other 19 mods going to be ?



#3 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 13 December 2012 - 05:01 AM

Hood, nose, rear tail section, under pan section, ruff, all for 4 fenders, front and back window section.  A lot of the stuff as two to three changes in them.



#4 JM485

JM485

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 517 posts
  • Location:California
  • Full Name:Josh Mouzakis

Posted 13 December 2012 - 05:04 AM

Should be cool, hope it all goes smoothly.



#5 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 13 December 2012 - 07:47 AM

Thanks for the kind words. I will have pics of the rim center as it's in ruff stage but will be changed using some cad programs and then in to the 3D Printing when it goes out. A lot of the parts will either be done in the new 3d stuff or changed and then in resin cast for the bigger parts. Plans are for this to having full working hood and trunk.



#6 James2

James2

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,456 posts
  • Location:Portage Co. Ohio
  • Full Name:JamesRiesII

Posted 13 December 2012 - 09:38 AM

that is a beautiful Camaro. Good luck, I am following.



#7 Ford guy

Ford guy

    MCM Avid Poster

  • Members
  • PipPipPipPipPip
  • 415 posts
  • Location:Shelburn Indiana
  • Full Name:Roy Snyder

Posted 13 December 2012 - 11:39 AM

This is going to be totally cool ! B)   Looking forward to watching the progression.

 

Roy the Ford guy



#8 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 13 December 2012 - 02:52 PM

68670_4636767370977_881141802_n.jpg32392_4636767290975_1957782564_n.jpg483499_4636767250974_2075506724_n.jpg205043_4636767770987_808960738_n.jpg



#9 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 13 December 2012 - 02:55 PM

Some of the body mods are a lot of vents was put into this car. The hood vents and also nose air induction vent and the relocation of the round running lights. The ruff was just a special job that did to change the look of the car when looking at it from the rear. I open up the trunk and will be doing all the inner work on that and brace with brass parts and then painting them. The turn does not open like a normal camaro as it was changed to open more from the top with a thick lip that will be not seen when the spoiler is put on.



#10 Doobie

Doobie

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,201 posts
  • Location:England
  • Full Name:Dave Chivers

Posted 14 December 2012 - 11:48 AM

lookin good so far I will be watchin this one for sure B)  ;)



#11 tjones87

tjones87

    MCM Avid Poster

  • Members
  • PipPipPipPipPip
  • 354 posts
  • Location:colorado city, tx
  • Full Name:Tim Jones

Posted 14 December 2012 - 11:54 AM

How did you remove the turn signals from beside the headlights? i am replicating my 1:1 camaro and will have to do that as well...thanks



#12 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 14 December 2012 - 05:38 PM

ground it out and will be filling it in with putty and smoth it out. The light was relocated to the lower front end area.



#13 tjones87

tjones87

    MCM Avid Poster

  • Members
  • PipPipPipPipPip
  • 354 posts
  • Location:colorado city, tx
  • Full Name:Tim Jones

Posted 14 December 2012 - 05:46 PM

ok cool...thats what i was planning on doing...I am having to recreate the original rectangle turn signal, like the non rs camaros....any idea on what you will do for the bumper? i am looking forward to seeing that as well...keep up the good work



#14 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 14 December 2012 - 09:30 PM

Bumper is in the same location, The middle part bumper will be made out of the resin grill using the upper support part of that as it has the same design and angle that is needed to make the two part one that goes across the grill area.



#15 tjones87

tjones87

    MCM Avid Poster

  • Members
  • PipPipPipPipPip
  • 354 posts
  • Location:colorado city, tx
  • Full Name:Tim Jones

Posted 14 December 2012 - 11:33 PM

sounds like a plan...will be watching this build closely..maybe give me some ideas for my build. keep up the good work



#16 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 16 December 2012 - 09:36 AM

316502_4650343870381_1571667418_n.jpg18825_4650343550373_1621313331_n.jpg380754_4650339790279_1210688921_n.jpg28756_4650343310367_1069645477_n.jpg196205_4650344030385_1621293359_n.jpg532486_4650344230390_327609669_n.jpg



Front air vent for the LS7 motor intake. This is just the same on how they did the real car as it is really wider the what the intake vent looks like., On the Front side vent this is just a outer vent to let out the heat and then the rear vent also I made a part that has a tube that will go to the rear brakes. The top ruff part is just a mod that they did and the molds is just some of the parts that this car will have on in resin from rim ring sizes to the duel fans for the radiator to the oil coolers



#17 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 16 December 2012 - 12:55 PM

68849_4651449058010_1717232879_n.jpg

 

 

CHECK OUT BOB BERTELSONS BRUTE FORCE CAMARO AREA 51 PAINTED AND RPM HOTRODS DID THE INTERIOR IN THIS MONTHS ISSUE OF POPULAR HOT RODDING !!!!!!



#18 Plasticfanatic

Plasticfanatic

    MCM Avid Poster

  • Members
  • PipPipPipPipPip
  • 400 posts
  • Location:Puerto Rico
  • Full Name:Fred Perez

Posted 16 December 2012 - 03:16 PM

This really looks great, like the body modifications a lot. This is going to be a great looking model.

#19 Chas SCR

Chas SCR

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 716 posts
  • Location:Michigan
  • Full Name:Chas Cochran

Posted 16 December 2012 - 06:06 PM

380720_4652703849379_867029706_n.jpg282401_4652704049384_1929493097_n.jpg222216_4652704209388_223446466_n.jpg



Putty the running boards in smooth and also got the marker lights taken out and smooth to the fenders front and rear. Both sides are now smooth fitted and also have the vents put in place. The rear section has been cut out and then filled in also.



#20 pharr7226

pharr7226

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 956 posts
  • Location:Atlanta, GA
  • Full Name:Rick

Posted 16 December 2012 - 06:29 PM

The body mods look great.  I like the use of the tape to make your reference points easier to locate. I will borrow that one for sure.  I'm looking forward to your updates.