Jump to content


1940 Ford Street Rod


  • You cannot reply to this topic
9 replies to this topic

#1 mrmike

mrmike

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,714 posts
  • Location:Nashua, NH USA
  • Full Name:Michael R. Siesicki

Posted 25 December 2012 - 11:20 AM

I decided to challenge myself today with a special project...building a '40 Ford Coupe Street Rod.  The kit is Lindberg's '40 Ford Coupe that I have been told to be almost unbuildable.  My goal was to get see just how far I can get building this kit today without getting into too much detail.  Here is what I am starting with...
40Ford01.jpg
There is a lot of flash on this kit.  I spent an hour removing flash and mold lines.
40Ford02.jpg
My paint is Testor's Guards Red.  I had trouble with this paint not spraying correctly.  I had set it back to Testors for testing and they said there was nothing wrong with it, even thought there is paint all over the top of the can.  They sent the can back with another nozzle and now it sprays OK.  Hmmm...
40Ford04.jpg
Well, it did spray OK, not 100% happy with how it sprayed though.
40Ford03.jpg
40Ford05.jpg
The wheels are being assembled.  Steelies and hub caps.
40Ford06.jpg
 
More to come...
 


#2 Jantrix

Jantrix

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 6,268 posts
  • Location:Tampa, FL. USA
  • Full Name:Rob Mattis

Posted 25 December 2012 - 11:57 AM

Mike, you should join my Nightmare kits CBP, with this.



#3 mrmike

mrmike

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,714 posts
  • Location:Nashua, NH USA
  • Full Name:Michael R. Siesicki

Posted 25 December 2012 - 03:18 PM

Thanks for the invite, Rob.  I'll consider it.

 

 

Well, I have been plugging away at this off and on during the day and this is as far as I have gotten.  I've gotten the interior assembled.
40Ford07.jpg
The chassis has been assembled.
40Ford08.jpg
The engine has been assembled and installed into the chassis.
40Ford09.jpg
This is as far as I am going tonight.  So far, it's not too bad, but this is still a crummy kit.  I did a mockup and the wheels are not centered in the fenders and the instructions are vague in some areas.  Plus, the paint is still not cured since it is enamel and not lacquer.  I used enamel since I thought that if I had used lacquer, the hot paint would have eaten the translucent plastic.  
 
More to come...     


#4 Joe Handley

Joe Handley

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 4,852 posts
  • Location:We-Go, Chitown, Ill
  • Full Name:Billy Joe

Posted 25 December 2012 - 03:25 PM

Looks good so far!

 

 

Apparently this kit was more or less a rip off of the AMT '40, so it was better than the other kits from it's original manufacturer.



#5 W-409

W-409

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 5,489 posts
  • Location:Vantaa, Finland
  • Full Name:Niko Lindström

Posted 25 December 2012 - 10:12 PM

Oh I didn't remember I have this on the stash, too. This is really a NightMare kit, I've started it but got stalled just because of the kit quality.... Maybe this project makes me to go back building it again, and maybe doing another entry to Nightmare Kits CBP (Two entries were allowed?).

 

Looking very good so far, I like the engine, but especially the wheels look nice. Fantastic color!



#6 mrmike

mrmike

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,714 posts
  • Location:Nashua, NH USA
  • Full Name:Michael R. Siesicki

Posted 29 December 2012 - 03:50 AM

I know this kit is junk, but it is a challenge for me and I do need to challenge myself from time to time.
 
I didn't like the stance and my first thought was to just glue the wheels on and be done with it.  Well, the modeler in me said to do it right and I started grinding away at the rear spring and the spring mount on the chassis with my Dremel and a sanding drum.
40Ford10.jpg
40Ford11.jpg
Now, that's more to my liking!
40Ford12.jpg
I am going to try and finish this '40 Ford today!
 
More to come...


#7 Erik Smith

Erik Smith

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 2,799 posts
  • Location:Spokane, WA
  • Full Name:Erik Smith

Posted 29 December 2012 - 04:35 AM

Nice work. I think it's kind of fun to build a kit with "issues". It's a challenge and learning experience. Looking good.

#8 slammedi'am

slammedi'am

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,946 posts
  • Location:Cleveland,TN
  • Full Name:Shane Harrold

Posted 29 December 2012 - 04:49 AM

Looking good!



#9 TimJ

TimJ

    MCM Regular

  • Members
  • PipPipPip
  • 58 posts
  • Location:Oldbury, England
  • Full Name:Tim Jones

Posted 29 December 2012 - 07:45 AM

Nice work.



#10 mrmike

mrmike

    MCM Ohana

  • Members
  • PipPipPipPipPipPip
  • 1,714 posts
  • Location:Nashua, NH USA
  • Full Name:Michael R. Siesicki

Posted 30 December 2012 - 04:20 AM

Thanks guys!

I have finished my '40 Ford Street Rod and it is posted in Under Glass.  I would like to thank all those who took the time to view and to comment on my WIP.