tbill Posted September 7, 2013 Share Posted September 7, 2013 So, after looking at all the trucks and trailers available, I'm wondering how much a difference there is between the two scales? By that I mean if you put a 1/24th trailer behind a 1/25th rig, does it 'look right'? I know it seems like a silly question, but as I don't have any 'samples' to look at, I don't have a frame of reference. also, sorry if this has been discussed before, I'm reading all I can..... Quote Link to comment Share on other sites More sharing options...
Eshaver Posted September 7, 2013 Share Posted September 7, 2013 Tom, usually on the large trucks , it won't be as noticeable . I usually see differences on say width of a passenger car or perhaps a wheel base difference . Even then, on some models , the difference is negligible . Sometimes , say an Arii 1958 Cadillac , uh the difference is huge Quote Link to comment Share on other sites More sharing options...
raildogg Posted September 7, 2013 Share Posted September 7, 2013 1/24 = 2 feet, per inch of scale 1/25 = 2 feet 1 inch, per inch of scale So a trailer 40 feet will be 1/24 = 40 x 12 = 480 inches / divided by 24 = 20.00 inches. 1/25 = 40 x 12 = 480 inches / divided by 25 = 19.20 inches. Does it look right to be smaller or larger, a question for the rivet counters and perfectionists. Quote Link to comment Share on other sites More sharing options...
ap40rocktruck Posted September 7, 2013 Share Posted September 7, 2013 1/24 = 2 feet, per inch of scale 1/25 = 2 feet 1 inch, per inch of scale So a trailer 40 feet will be 1/24 = 40 x 12 = 480 inches / divided by 24 = 20.00 inches. 1/25 = 40 x 12 = 480 inches / divided by 25 = 19.20 inches. Does it look right to be smaller or larger, a question for the rivet counters and perfectionists. Very good, a slightly easier way to measure for modeling in the 2 scales are: 1/24 -- 1/2" = 1' 1/25 -- 1" = 1 mm my 2 pennies Quote Link to comment Share on other sites More sharing options...
TUFF TIN Posted September 7, 2013 Share Posted September 7, 2013 There is no such thing as a stupid question. There is, however, from time to time stupid answers but none here.Mike Quote Link to comment Share on other sites More sharing options...
lapazleo Posted September 7, 2013 Share Posted September 7, 2013 It also depends on how close to scale the actual kit is. Some kits are out of scale and are closer to another scale than what they are claimed to be. If a 24th scale kit and a 25th scale kit are in scale there will be no noticable difference. Quote Link to comment Share on other sites More sharing options...
BigBad Posted September 7, 2013 Share Posted September 7, 2013 (edited) As far as tractor trailers go, some don't mind the width difference as it is not by much. But if you are picky on this as I can be, you'll see the 1:24th scale tractor's rear wheels poke out slightly from under the 1:25th scale trailer. Another thing, the tractor's wheels won't be the same size as the trailer's unless you swap the trailer wheels for the bigger 1:24th scale one's. But then again, that won't matter much as there are all sizes(19.5 to 24 inch rim diameter)of wheels with different sidewall heights on trailers. Edited September 7, 2013 by BigBad Quote Link to comment Share on other sites More sharing options...
tbill Posted September 7, 2013 Author Share Posted September 7, 2013 thanks for the replies everyone, biggest reason I was wondering is all the kits I have so far are 1/25 [rigs and trailers], but I saw a few 1/24th trailers I liked the look of. also being the genius that I am, never considered the actual math to figure it out . thanks again all. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.