Jump to content


slowlylearning

Member Since 29 Nov 2012
Offline Last Active Sep 06 2014 09:32 PM
-----

Topics I've Started

Scratchbuilding 'Blank' Wheels

20 April 2014 - 04:16 AM

You'll need:

Dremel

2 to 3mm styrene rectangle rod OR 2 to 3mm styrene sheet (I didnt have that hence the rod)

Sanding sticks/paper

Glue

Blade

Grinding/engraving bits that come with Dremels

Sheet styrene .5mm or slightly smaller

Spare Tyre

Sanding-Drum Dremel bit

 

1_zpsef410f21.jpg

 

Cut a strip of .5mm or smaller sheet styrene. Cut it quite long incase of any mistakes (I made plenty of its too short practicing this). Cut the strip as wide as the tyre you're using.

2_zps7bbaf759.jpg

 

Curl your strip of styrene around your hobby knife handle from both ends a few times, it help the strip of sheet styrene to keep its curve.

3_zps942fd5fb.jpg

 

Curly whirl-y!

4_zpsdc80974a.jpg

 

Test fit it in the tyre and chop off the excess to make a since ring of strip styrene, and glue the ends together on the inside while it's in the tyre.

5_zpsc10883d6.jpg

 

Once the glue has dried pull out the rim about a third of the way and put some glue on the outside of the rim, repeat for both sides.

6_zpse9177d50.jpg

 

Cut a much thinner strip to set the deepness of the wheel, Mine will be quite deep-dish so the thin strip is glued almost all the way around towards the back of the rim. Use plenty of glue, it helps with the rigidity of the rim.

7_zps60d32a04.jpg

 

You can see here I left a gap because I cut the strip too short, silly me!

8_zpsce552e5e.jpg

 


Deep Dish Wheels & Sparkplug Boot Tubing

28 March 2014 - 01:56 AM

Deep Dish Wheels

 

What you need:

Sanding sticks

Hobby-Knife

Adorably small saw (cutting-wheels leave a lot of molten plastic slag)

A Suitable Wheel

 

1959353_757551944255600_502580527_n.jpg

 

Use your adorably small saw to shop the front of the wheel from the rest of the rim.

1948129_757552030922258_912675909_n.jpg

 

Like this-

1982271_757552034255591_1365319131_n.jpg

 

Clean that sucker up!

10154338_757552090922252_641054560_n.jpg

 

Using the backside of the rim as the front, you now have a deep dish!

1904016_757552120922249_861865579_n.jpg

 

If you want to use a smaller tyre, and the only ones you have come with too-tall sidewalls...

1010119_757552277588900_334559515_n.jpg

 

Carefully slice them off to fit!

10155821_757552410922220_510869348_n.jpg

 

Find different iterations that work for what you want them for.

1557461_757552444255550_108511378_n.jpg

 

 

 


Custom Trim and Dipsticks

21 March 2014 - 01:33 AM

Couple of simple small tutorials :)

 

Custom trim (side mouldings) (takes a little while)

 

You'll need:
-masking tape (I used Tamiya and a bigger low tack type)
-easily workable putty
-model car body (I used an old one for practice)

 

Tape off a design

 

Make a big mess, build up the putty a bit over theasked off area, remember, its easier to add more than enough now rather than later.

Wait for the putty to become slightly tacky but not overy clumpy, I waited about 5 minutes but it would vary with different putties.

 

Unmask it carefully and let harden.

 

Once its hardened you can very carefully shape it with sandpaper (I used 800grit), the end of a file for the edges and an exacto for those trickier bits.

I shot undercoat on it at this point so it was easier to see where I skrewed up and took too much off/chipped it.

After this its just a matter of adding small amounts of putty to the problem area and working it more.

Its a bit of trial and error, but thats why its fun!

 

1979533_753875931289868_162860318_n.jpg

 

1381325_753876454623149_655605254_n.jpg

 

1619289_753876461289815_1444574122_n.jpg

 

1450296_753876471289814_198542086_n.jpg

 

10151257_753876114623183_1421909854_n.jp

 

1625742_753876631289798_1040193996_n.jpg

 

Stickin in a dipstick! (5-10 minute detail modification)

 

You'll need a pinvice with 1mm drillbit,sparkplug boot tubing, .5mm wire, engine and your trusty xacto.

 

Drill a hole in the side of your engine, from reference you can decide how accurate you want to be.

 

Wrap the .5mm wire around your 1mm drillbit so it forms a loop like in picture 3 and cut off the excess.

 

Put the straight end of the looped .5mm wire in the end of the sparkplug boot tube.

 

Place it in the aformentioned super-accurately placed hole you drilled in the engine and bend it about until youre happy with the way it looks and youre done!

 

You can also add a tiny 'washer' between the loop in the 5mm wire where it goes into the sparkplug boot tube to add a bit more detail, or use smaller copper tubing instead of the sparkplug boot tube for a smaller scale look.

 

1922436_753795354631259_192745077_n.jpg

 

1517505_753795414631253_1763274678_n.jpg

 

1098380_753795474631247_1299214779_n.jpg

 

10150691_753795494631245_388508473_n.jpg


Salt Lake 5-Window

27 October 2013 - 06:23 AM

GOt this chopped TPB 5-winduh a while back, got the itch.

Heres what happened to the tyres.

20131026_173542_zpsf0f4f85f.jpg

Drilled some speed-holes on the back plate because fast!!

20131027_185012_zps80864df1.jpg

Got the bare framework for the front mount of the suspension, switched it to a not-as-long one for a more arrow-like effect.

20131027_185003_zps684dad91.jpg

This will be the stance more or less. Probably barely a mil higher in the front.

20131027_184944_zps93d6ca13.jpg

Heres where I grinded some material off the back of the speed-holes to get it looking thinner.

20131027_165957_zps726f6ab4.jpg

Gotta chop up the firewall to get that Dodge donk sitting a bit further back so the rocker covers dont hit, wish me luck lol.


Model Building Live Streams

29 August 2013 - 02:21 AM

Hey all, how many of us would be interested in seeing a model building live stream? Iv done a few short streams in the last few months and would like to see how much interest there is for them.

 

Also, what sort of stuff would you all like to see on a stream?

 

Iv seen some Youtube videos of model building and would love to get more interaction with other model builders through live streaming. Theres a chat-window on the streaming site I use, so you could all tell me how wrong Im doing everything :P

 

Cheers,

Kc