Jump to content
Model Cars Magazine Forum

IanB

Members
  • Content Count

    41
  • Joined

  • Last visited

About IanB

  • Rank
    MCM Regular

Previous Fields

  • Scale I Build
    1:72

Profile Information

  • Location
    Cape Cod USA
  • Full Name
    Ian Brand

Recent Profile Visitors

1,458 profile views
  1. Hi all, Due to the positive feedback I received for my 3d printed friction dampers, I have made them available via Shapeways for anyone who is interested. https://www.shapeways.com/shops/ibdetails They are available as a set of 6, and as a single unit in case anyone breaks one and needs an extra! They are not "handed", instead the mounting nuts and friction adjuster are mounted on pedestals and should be removed with a razor saw, then reattached after the shocks have been mounted. The mounts are not included: either modify the kit ones with .040" (1mm) rod or scratch new ones, the mounting holes are integral to the part. I searched all over for aftermarket parts for this old kit and couldn't find any, so hopefully these will help people out! I hope you like them! Ian
  2. The shocks are now available on Shapeways as a 6 piece set, and there is also a one-off available if someone needs a replacement after breaking one... https://www.shapeways.com/shops/ibdetails I hope you like them! Ian
  3. Hi folks, I haven't forgotten about this, I just have other builds that are priorities at the moment. Having said that, I got bored with rigging the Short so decided to tackle a little project on this one as a break. Airfix moulded the radiator badge too low so I needed to find a way to put that right. I tried making a mould of it a few months back and destroyed the badge, so I ordered a new rad shell from Airfix. After trying to mould it again I decided it wasn't going to work: I couldn't get the detail fine enough, or make it thin enough. I therefore bit the bullet and decided to graft it! I first removed the badge from the replacement shell, then marked out where it should go and drilled out the centre line. I then slowly and carefully widened the hole until the badge fitted. The top of the shell is a little flatter than the front, so hot water came into play. I made sure I checked it constantly to see if it would bend and in the end I got it sufficiently flat to insert it into the hole in the shell. The edges of the joints at the rear were filled with Mr Dissolved Putty to fill any gaps and give it a little more strength, and when it's dry I'll fill and smooth off the joins at the front..... Ian
  4. These arrived in the mail today.... I'm well chuffed! Translated: Very happy with how they've turned out. There's no way I could have got this level of detail by any other means. Now I need to reprint the decals..... Ian
  5. I received the prototype this week and I'm very pleased with it! The size and angles look good, so I now need to add the adjusters and mounting bolt heads. I've decided that for ease of printing and to reduce my design workload, instead of making 6 different shocks, (which would be required if I included the mountings) I will leave the mounts off - these can either be scratchbuilt, or removed from the kit shocks and modified as necessary. I will add the bolt heads and adjusters in their correct positions, but raised slightly on a small "pedestal" so that they can be cut off with a small razor saw and fitted on whichever side needs them, thus getting around the left and right handed differences. Doing this means I only need one master and will be able to print 6 identical parts, then easily modify each one to fit where it's needed! Removing the adjusters will be necessary anyway to add the decals for the adjusting plates. I'm looking forward to getting these finished and fitted! 8) Ian
  6. Has it really been 3 months since my last progress post? Following another modeller's lead on another forum, I downloaded a trial version of Rhino and have been playing around designing some replacement shocks for this, to be 3d printed. I submitted my order for the prototype today and should have that in a couple of weeks. That will enable me to check the fit and modify it as necessary, then order the full set of 6...... Ian
  7. I haven't forgotten this one, just been busy with work, and still waiting for more details on the engine plumbing. Thanks for all the interest! Ian
  8. Nearly done with the carb linkages now. The choke mechanism is just resting in place and will be removed for painting before it's installed. I used aluminium tube for the main control rods, with .030 plastic rod drilled out and slipped over it for the brass bushes on the butterflies, these will also be painted tomorrow. The small circular pieces are from a sheet of 1:72 photo etch WWI prop hubs - the perfect size, and the holes are already there! Once the choke is fitted, I'll add the wiring for the mags and fan, the throttle linkage from the pedal, and then the steering column, with the rest of the linkages... Thanks for looking in! Ian
  9. I started work on the throttle and advance/retard linkages today. The cross shafts are 0.020" and 0.030" rod, to allow for smaller diameters for the rest of the links. I also made the cooling fan, but can't fit that until I have attached the ends of the oil lines running along the side of the cylinder block - which requires knowing where they go! I'm still not too sure that the fan blades are correct - they just look too long....still thinking about that one... Ian
  10. Got the other side of the ignition done, after an afternoon of wrapping tiny wires with strips of masking tape....not too sure about it, but I think it'll do... Ian
  11. Here's a little update...work now is fairly slow due to the detail, but each added piece makes a huge difference. I've added all the foot pedals and the brake linkage to the compensator shaft, and started on the engine wiring and plumbing.... I had to remove the part on the compensator shaft that the brake rod attaches to as I made it too short and the rod fouled the chassis. A new part was made and the rod is now straight and clear of the chassis rails. That's it for tonight, I have a 5am start tomorrow. See you all later! Ian
  12. Thanks Frank, here you go.... Not much in the way of progress lately as I've been concentrating on the bulkhead details. That is done as far as is needed at the moment, which means the next milestone has been reached - the bulkhead has now been fitted to the chassis. I also spent much of this morning making the clamps for the intake plumbing from the blower.... I'm pleased with how that's turned out, especially as it was one of those "I'll do it later" (ie. how the hell do I do that?) jobs, now thankfully out of the way! I used thin plastic strip wrapped around the trunking, then carved 12 small pieces of 1mm square rod to represent each end of the screw clamp and glued those in place. 0 .4mm aluminium rod was added for the rods, and more resin nuts - I only added the 3 at the front of the clamps, and one under the tie rod. Starting to look like something now! Thanks for looking in, Ian
  13. Thanks, much appreciated! I'm putting in as much as I can, no real excuse not to as it's such a large scale. The only problem is getting accurate references.... A little more done - throttle pedal and mounting, and the linkages for the front brakes..... Thanks for looking in.... Ian
  14. I now have the pedals finished, with the exception of the actual foot pads at the end, which I will add when the bulkhead is in place. I've also finished the brake compensator. There are still 4 more actuators to make for the handbrake and front brakes, but there's not much more I can do on the brake system until I get the shock absorbers built and fitted, so that will be the next major job (I'm trying to find a good and reasonably priced source for the decals for those). That and making a start on the engine detailing, when I finally receive the hose fittings I ordered in September! I've been told they'll be here soon, so that should be a job for this weekend. Ian
  15. A little more progress to post.... I started adding details to the carbs, but I'm not going to go further just yet as I've emailed a museum in the hope of getting pics of their car so I can do them properly. If they don't reply I'll just stick with whatever I make up, at least it will be better than nothing. The dynamo and its bracket and wiring are in place.... along with some of the detail on the front of the bulkhead... I have also added the drivetrain and rear end, adding the shackles I'd made previously, and more resin nuts! I discovered that I've fitted the left rear spring slightly off - it's sloped very slightly inwards, so the differential is centred with reference to the chassis rails, not the springs. This job would have been a lot easier if I'd bought aluminium rod for the shackles instead of using the brass rod I had, and painting it.....lesson learned! Finally, I've made a start on the clutch and brake pedals, and the mounting shaft. Airfix kindly provide the mounting points on the chassis rails, but once again, for no apparent reason, don't actually supply the shaft and pedals - they do provide little plastic blobs that bear no resemblance to the pedals - would it really have been too much effort to have done them properly? I was hoping to make the pedals in one piece but the curve at the top end proved too much. Still, it should make it easier to put it all together if I add the end later. Thanks for looking in! Ian
×
×
  • Create New...