Search the Community

Started this project last summer with a simple angle chop to a 34 ford coupe body. Reformed the front fenders from the wrap around wheel to the sweep of the 32 fenders I like better. Decided it needed a bit more attitude and angle-sectioned the body for a lowered stance. So far I'm liking the direction its going. This is a snaptite kit, but only using the body, will fabricate a chassis and install a motor with opening doors and trunk. Started with this After

Finally, I have completed the 1954 Hudson Hornet custom coupe.........to recap the build : 1. I sectioned out about 6 scale inches from the sides, back and front of the car. 2. I chopped about 6 scale inches from the top by cutting a couple of wedges from the upper front and lower back of the A pillar, 6 inches from the B pillar and a 6 inch die-angled cut in the rear pillar, so that the top was "slid back and down" to the new lowered position and then secured with glue. The B pillar has a new top section filled in where the old pillar was moved to. I added a new chrome trim accent strip to the sides in a flowing pattern from the front, just back from the headlight, down to the rear fender back by the rear bumper. 3. The rear fender top line was raised 1 scale inch from the end of the rear quarter panel window to the new tail light fixture to give the fender line a very small fin as a fore-runner of the larger fins to come in the end of the 1950 ear with a sharp "C" look to it. The tail lights are a mix of epoxy and clear red paint dropped into the opening after the opening was painted reflective silver. 4 on the rear deck, I formed a faux- continental kit look into the rear deck to give the rear deck a little height because the nose tends to be a little high on this car. 5. the hood was smoothed out by removing the large flat area that was molded on the real car. 6. The headlights were frenched and filled with liquid mask so that the chrome finish was protected from the painting. 7. a black mesh inner grill was installed to the grill opening which was covered with a "Toothy" grill from my parts box. 8. I replaced the 6 banger stock engine with a Revell chrome Cadillac V8 with 6, 2 barrel carbs. 9. the engine bay firewall and inner fenders were smoothed and covered with bare metal foil, as was the inside top of the hood. 10. The hood was hinged on the left side to open sideways, just to be different. 11. The stock wheels and rear view mirrors were used. 12. Chrome "lake" pipes lifted from the Revell 1949 Mercury kit seemed to fit this car perfectly, so they were added. 13. The stock front and rear bumpers were installed 14. And finally the paint. The car was primed, sanded and re-primed. I mixed up a dark gold paint from Tamiya bottled paint which was sprayed on the hood, top and sides of the front fenders and doors. Once dry, I installed some custom flame masks that my brother designed on the computer and cut out of vinyl ( he is a custom sign maker) ....these were old masked that I used on a Plymouth street rod from about 8 years ago and were just rolled up on a shelf. I installed the masks on the hood and side fenders ( not an easy task I might add). Then the entire car was sprayed light gold. As the paint dried I removed the masks. Once dry, I lightly sanded the area to remove the ridge caused by the paint mask and the thickness of the paint. Once smooth I touched up a few spots and then painted the nose and front side fenders with Tamiya clear red. When just about dry, I painted the entire car Tamiya clear orange, I wanted to give the front end, which has the ghost flames a darker, more red glow, that is why the red is under the orange. Lastly, as the orange as about dry, I mixed a few small scoops of extremely fine gold metalflake into the clear orange so to give the candy blood red/orange a metal sparkle. In the sun, it really poops. And finally, when dry, the car was clear coated with 3 layers of clear, and once dry, it was waxed out and buffed 15. Once the body was dry, the Bare Metal Foil was applied to the side strip and the window trim. 16. OOPS, I forgot, the interior is made up mostly from the door panels, console and seats from an Infiniti G35 coupe with a modified Plymouth dashboard and the steering wheel from the Hornet kit. Thanks it, I hope you like it......I know I am very happy with the result.......I think the original car is chunky and too tall....I think the section and chop bring the car into the proper proportion, and the lowered stance make this into a great 50's lead sled. Here are the finished pictures. Thanks for looking...............

Finally finished my 49 Merc.(The Golden Diamond) This has been a long on going project that started at least 8 years go. It all started with a birthday gift from Alton Spence. (once again, Thanks Alton) and much needed pushing by my brother from another mother Luke Karosi as well as inspiration from his magazine, Kustoms Illustrated. I chopped it and hard -topped it then sectioned the body 4 scale inches, added the canted quad headlights with a kustom fitted grill. The tail lights were from the parts box and were canted as well. All of the interior was kustom made using materials from parts boxes and styrene pieces. The dash is a kustom fit 59-60 Chevy unit with a kustom steering wheel along with hand made Lakes Pipes from Aluminum rod. Glass was also made from templates seeing the original no longer fit. But enough with all the jibberish, on to the pics...