69NovaYenko Posted October 10, 2015 Share Posted October 10, 2015 I have a Johan 69 Javelin annual with a missing windshield post. Is there any alternative beyond butchering a body of another car for a post. I`m sure others have encountered this problem; so I`m seeking the sage advise of this group of savvy builders on how you resolved this issue. Quote Link to comment Share on other sites More sharing options...
chunkypeanutbutter Posted October 10, 2015 Share Posted October 10, 2015 Sheet and strip plastic. Easiest way, really. Time consuming, but rather easy. Quote Link to comment Share on other sites More sharing options...
Atmobil Posted October 10, 2015 Share Posted October 10, 2015 Yes, I think that will be the best way of doing it. I have never reconstructed a complete missing post but I have reconstructed a post that was badly bent and broken. If the other post is there then you can use that as a template to make a new one. Quote Link to comment Share on other sites More sharing options...
Ace-Garageguy Posted October 10, 2015 Share Posted October 10, 2015 As Miles says, strip plastic. Think about what you need to do, measure and fit carefully. Not hard. I had to replace both pillars on this blue body shell after some clown tried to chop the top, butchered it and gave up. Primered. Done. Quote Link to comment Share on other sites More sharing options...
Snake45 Posted October 10, 2015 Share Posted October 10, 2015 If you have or can borrow ANY other JoHan '68-'74 Javelin or AMX kit or promo body, you can "sili-clone" the post by taking a silicone mold off the good body, putting the mold on your body, and carefully filling the mold with JB Weld or some other epoxy. I have several bodies I'll be doing this with. Quote Link to comment Share on other sites More sharing options...
StevenGuthmiller Posted October 10, 2015 Share Posted October 10, 2015 Never done it myself for obvious reasons.That's my first consideration when I buy a vintage kit.I don't even consider it if the roof pillars are damaged.I don't mind paying a little more for a good one.My first inclination would be to check my other kits that have a similar A-pillar configuration & see if I could rob one rather than build one from scratch.But I would not shy away from at least trying to make one from styrene strips. There's really not a lot to a windshield post. Steve Quote Link to comment Share on other sites More sharing options...
69NovaYenko Posted October 10, 2015 Author Share Posted October 10, 2015 Thanks one and all for the suggestions so far.Yes, I think that will be the best way of doing it. I have never reconstructed a complete missing post but I have reconstructed a post that was badly bent and broken. If the other post is there then you can use that as a template to make a new one.Atmobil what method do you employ to straightening badly "bent" post? I have a 69 GT.T.O. with that issues as well. I`d also like to hear the suggestions from you other go folks as well. Quote Link to comment Share on other sites More sharing options...
Atmobil Posted October 10, 2015 Share Posted October 10, 2015 Thanks one and all for the suggestions so far.Atmobil what method do you employ to straightening badly "bent" post? I have a 69 GT.T.O. with that issues as well. I`d also like to hear the suggestions from you other go folks as well.The model I did this on was the AMT Ford C600 stakebed truck. The drivers side A-post was broken at the bottom and bent inwards with a bend about in the middle of the post. I first tried to bend it bakc buy putting it in warm water and gently bending it but it was not very good and because the post was very thin it broke where the bend was. I was able to use the upper half of the post as a guide and with som sheet styrene I made a new lower half of the post. It was still very weak but when I got the windows inside the truckcab it was not a problem. Quote Link to comment Share on other sites More sharing options...
Earl Marischal Posted October 10, 2015 Share Posted October 10, 2015 As Miles says, strip plastic. Think about what you need to do, measure and fit carefully. Not hard. I had to replace both pillars on this blue body shell after some clown tried to chop the top, butchered it and gave up. Primered. Done. Pardon my ignorance but what is the red car? Thanks steve Quote Link to comment Share on other sites More sharing options...
chunkypeanutbutter Posted October 10, 2015 Share Posted October 10, 2015 It's a '70 Chevelle. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.