Eric Macleod Posted March 29, 2017 Share Posted March 29, 2017 I was much more productive on this one than I expected. There are a few more details like sunvisors, a mirror and license plates to finish but otherwise I am calling this one done. Not much of a WIP in the other area. I just got busy and built it. Thanks for looking. Quote Link to comment Share on other sites More sharing options...
Eric Macleod Posted March 29, 2017 Author Share Posted March 29, 2017 One other thing I will add is this was by far my most difficult model to foil ever. As you can see it is a long way from perfect but I consider it a major accomplishment along the path of learning this skill. I have a few more Lincoln Convertibles of the '60's to do and will hopefully improve as I go. Plus, on the very same model I tried using a new dual action air brush. That was a learning experience. So...this is, at best, an imperfect model, but a great source of learning for me.Eric Quote Link to comment Share on other sites More sharing options...
Jim N Posted March 29, 2017 Share Posted March 29, 2017 Looks good! Quote Link to comment Share on other sites More sharing options...
GMCMAN52 Posted March 29, 2017 Share Posted March 29, 2017 Nice built. Had borrowed my Uncles Lincoln that was a Baby Blue hard top to my wife and I 's High School prom. That's for the flash back into our past in 1971 Quote Link to comment Share on other sites More sharing options...
bbowser Posted March 29, 2017 Share Posted March 29, 2017 Nice banana boat . Seriously, perhaps my favorite era Lincoln, you did well. Foiling the thin trim on 60s cars is tougher I think than the miles of trim in the 50s. Quote Link to comment Share on other sites More sharing options...
donb Posted March 30, 2017 Share Posted March 30, 2017 Looks good. Nice interior work too Quote Link to comment Share on other sites More sharing options...
ChrisR Posted March 30, 2017 Share Posted March 30, 2017 Nice! great colour. Quote Link to comment Share on other sites More sharing options...
disabled modeler Posted March 30, 2017 Share Posted March 30, 2017 Looks good to me..nice build. Quote Link to comment Share on other sites More sharing options...
PARTSMARTY Posted March 30, 2017 Share Posted March 30, 2017 Very cool !!! Quote Link to comment Share on other sites More sharing options...
Eric Macleod Posted March 30, 2017 Author Share Posted March 30, 2017 Thanks for all the positive comments everyone. This was a true labor of love. There is another one in the works being build by Ron Hamilton. He has a lot more ability than i I have come I'll look forward to seeing what it looks like. I appreciate everyone checking this out. Eric Macleod Quote Link to comment Share on other sites More sharing options...
crazyjim Posted March 30, 2017 Share Posted March 30, 2017 Never seen one in yellow. Nice job. What's the chrome thing on the back of the front seat? Quote Link to comment Share on other sites More sharing options...
Eric Macleod Posted March 30, 2017 Author Share Posted March 30, 2017 That is a Tonneau windshield which is an after market accessory that was made by the American Arrow Corp. When raised it really reduced the amount of wind in the car. It also added a bit of class for parades and weddings. As to the yellow, oddly enough I've owned three Lincoln convertibles painted yellow over the years. Thanks for the comment. Quote Link to comment Share on other sites More sharing options...
vintagercr Posted March 30, 2017 Share Posted March 30, 2017 Very nice! Quote Link to comment Share on other sites More sharing options...
Ron Hamilton Posted March 31, 2017 Share Posted March 31, 2017 (edited) Eric,I like the build in the color combination you chose. Bare Metal can be a killer, as it has at times given me fits, and this car has more trim on it than meets the eye. I have cut the roof from the sedan, and my next step is the flipper panel. Once I get that done, I'll snap a few pictures and start a thread on this one. I may even attempt an up top, since I was able to salvage the roof, and the shapes are similar between the two. I used the brochure, which had several pictures of the car. There was an Aqua and a Dark Ivy Green convertible in the brochure. Both are very nice, but I am leaning towards Triple Black, which I think will be stunning, and besides, I have the paint. I still have to get back to the '64 sedan too. It is ready for primer. Edited April 1, 2017 by Ron Hamilton Quote Link to comment Share on other sites More sharing options...
microwheel Posted March 31, 2017 Share Posted March 31, 2017 Your build turned out nice. BMF work is always a challenge. And with some models even more than others. But the best way to get better at doing it is by just diving in and doing it. I've tried many different ways of working with it over the years, and there are times it still gives me fits. My tools for working with it, is a exacto knife with a brand new unused blade, and a hand full of q-tips and a hand full of tooth-picks. I cut more foil than I need, (yes you will waste some) and apply it, then I press it down with a q-tip, then I trace every inch of it with a tooth pick and then, using just the weight of the exacto knife (no physical pressure at all) I do just what I did with the tooth pic, basically just allow the knife blade to gently trace the edges of the areas being trimmed. then again gently use a tooth pick to trace the edges and help peel away the excesses. There are still times where the areas being covered in BMF will be so obscure from paint build up that the knife blade with want to jump off track on you. That's where patience comes into play. Don't be in a hurry with the BMF work. Take your time and take lots of brakes, it will pay off in the end. Also in case you haven't figured it out yet, remember that the first 1/4 inch edges all the way around of the BMF sheet doesn't have very much if any sticky backing and isn't really usable. Hope I am not out of line offering you some tips on using BMF. Just trying to help. Quote Link to comment Share on other sites More sharing options...
Mike C Posted March 31, 2017 Share Posted March 31, 2017 Nice model but I know what you mean about BMF. It is a skill. You need a polished glossy surface for it to stick well and give a smooth look, it's thinner than a layer of paint. And you need a fresh, sharp blade and a steady hand. There's a new product you might want to try but you still need to be a skillful modeler to apply. It's called Molotow Liquid Chrome. Just google it. Actually you should be able to find it on YouTube as there are a few videos on it. Quote Link to comment Share on other sites More sharing options...
Eric Macleod Posted April 1, 2017 Author Share Posted April 1, 2017 Ron, I will look forward to following your thread. You have probably figured out by now that some scratch building will be needed for the flipper panel and area behind the back seat. Jim and Mike, the advice about the Bare Metal foil is greatly appreciated. I'm trying to improve my basic skills as a means of becoming a better modeler. That will no doubt make for more satisfying models. Your help us greatly appreciated. Thanks for looking guys.Eric Quote Link to comment Share on other sites More sharing options...
Classicgas Posted April 1, 2017 Share Posted April 1, 2017 Nice boat. Your skills with BMF will improve over time. Quote Link to comment Share on other sites More sharing options...
CometMan Posted April 3, 2017 Share Posted April 3, 2017 Nice work, Eric! That color was very popular through most of the '60's-early '70s, but don't see too many Lincolns in it! Well done. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.