[[Template core/front/global/utilitiesMenu does not exist. This theme may be out of date. Run the support tool in the AdminCP to restore the default theme.]]
  • Announcements

    • Dave Ambrose

      General Usage   05/10/2017

      If someone is acting badly, either in a forum or a private message, please report it. There are conveniently located buttons for sending the post to the moderators. 
absmiami

1924 Delage GP - a what ?

Recommended Posts

So, the lab-metal paste dried well and is sandable - but it was not  fine enough to grip the small surface imperfections

I ended up sanding most of it off and applied some more soft solder to the surface to fill in the larger surface pitting ...

working - just have to be careful not to apply too much heat to the metal 

IMG_0633.JPG

IMG_0632.JPG

Share this post


Link to post
Share on other sites

pix still loading wrong - oh well

the car has rows of copper rivets - like everywhere

working here on the rivets that attach the hinge on either side of the fuel tank cover

rivet rows lined up with scribed lines and a brass gadget that is bent from rod to locate the holes properly

holes are .021 with corresponding copper wire clipped in and sanded

rivets are close to scale and are just visible once all the sanding is done

IMG_0639.JPG

IMG_0638.JPG

IMG_0637.JPG

Share this post


Link to post
Share on other sites

okay - the pix are now saved properly and loading right side up - aren't computers great !

the patterns for the rivets are marked in hi-liter

makes it easier to mark the rows and patterns

and easier to photograph  ...

IMG_0644.JPG

IMG_0645.JPG

Share this post


Link to post
Share on other sites

working my way around  the  fuel tank cover with the rivets - just glue the copper wire in and clip close - but not too close - to the surface of the body

with the rivets in place in pic 3 - but not yet filed - has a sort of steam punk look - maybe try this on another project

in pic 4 the copper wire protrusions are filed and then sanded flush with the surface

got lots more of these to make - already broke one #75 drill bit ...

IMG_0646.JPG

IMG_0647.JPG

IMG_0648.JPG

IMG_0650.JPG

Share this post


Link to post
Share on other sites

I am glued to my seat on this one! Keep up the good work.

Regards

Brian Kroon

Share this post


Link to post
Share on other sites

You have the patience of a saint.  Watching this from a great distance.  And is there a bowing smiley?  :rolleyes:

Share this post


Link to post
Share on other sites

the great pix on the first page show that the driving compartment body-work is edged in  brass trim

in the deepest darkest depths of my workbench tool chest I located some brass  "L"  angle  bar

it's been sitting in a pile of misc brass and alu stock that I've had for years - well actually - decades

the stock is .050 in height/width - just over a scale inch - which is close enough

the brass was heated so I could bend it - using a grabber and pin vice on either end

then super-glued to the body in sections - the first sections are shown - I'll work my way around the opening with 6 or seven lengths of this stuff

then filed to shape

now back to those rivets ......

IMG_0652.JPG

IMG_0651.JPG

IMG_0653.JPG

Share this post


Link to post
Share on other sites

rivet rivet  ...

rivet rivet  ....

Q for 1500 GP  (and thanks for the compliment)

the brass trim around the driving compartment on the restored car appears to have a weathered or aged or slightly darkened finish

do you agree - do you know whether the restorer was able to use the original trim - I doubt it

probably took care to finish and present the trim in a "vintage" look - do you agree  ??

got some chemical darkening agent that I can use on the trim strip  ...

IMG_0654.JPG

IMG_0655.JPG

Share this post


Link to post
Share on other sites

so having broken my last  #75 drill it was off to the local hobby store for some more provisions

yes - there is still one lonely hobby store - specializing in trains - in Miami -

Ready to Roll - for you train fans - and they carry a good assortment of scratch-building supplies

for the remaining rivets on the body I'm trying some phosphor bronze wire - .020

the gadget in the picture  marks the metal at .100 intervals, and was made from this wire - holes drilled with #76 drill

gonna use some drill lubricant - so I don't break all of my #76's ...

these rivet holes will crawl around the cowl and down the length of the body  - as the body was riveted in this manner to the chassis

IMG_0656.JPG

Share this post


Link to post
Share on other sites
13 hours ago, absmiami said:

rivet rivet  ...

rivet rivet  ....

Q for 1500 GP  (and thanks for the compliment)

the brass trim around the driving compartment on the restored car appears to have a weathered or aged or slightly darkened finish

do you agree - do you know whether the restorer was able to use the original trim - I doubt it

probably took care to finish and present the trim in a "vintage" look - do you agree  ??

got some chemical darkening agent that I can use on the trim strip  ...

 

 

Yes, you're right, I doubt too ... so I agree ...

I'll ask to Patrick Delâge in Retromobile next friday ... but I remember that the story about this restoration/reconstruction was not very clear with the original used parts ... :wacko:

What a good job you do on this model with so detailled parts , I'm falling of my chair ...

Share this post


Link to post
Share on other sites

completing the brass trim around the driver compartment and drilling a bunch of holes for the rivets for the engine bulkhead and the chassis 

pic 3 shows the bronze wire product that I am starting to use for these rows of rivets

IMG_0658.JPG

IMG_0660.JPG

IMG_0661.JPG

Share this post


Link to post
Share on other sites

with the rivet holes drilled it's time to make and attach the lip along the bulkhead line that retains the bonnet

re-profiled the under-side of the cowling with a steel cutting tool

cut some .015 evergreen plastic strip to glue - epoxy - to the underside of the cowling

the tape along the edge of the strip is temporary - just there to help align the strip while gluing ...

IMG_0663.JPG

IMG_0664.JPG

IMG_0666.JPG

Share this post


Link to post
Share on other sites

with the strip glued in place I have to re-drill the rivet holes and glue in the wire for the rivets

most of the stems on the underside will stay there

they will help locate the bulkhead - which will probably be plastic with thin sheet aluminum glued to the front

busted a couple more drills this weekend - even with the drill lubricant ...

next is the rivets for the instrument panel frame - gotta do this together with the frame support so that everything is aligned ....

IMG_0667.JPG

IMG_0668.JPG

IMG_0670.JPG

Share this post


Link to post
Share on other sites

Andrew, I spoke with Patrick Delâge last friday in Retromobile.  So I have documents on the 2LCV to scan for you and I have the complete story of the restoration/re-construction of this car ...  please, send me your Email on PM ...

... and, for your information, I bought this fabulous book (and dedicated by the author) ...

bugatti-et-delage-a-la-conquete-de-l-europe-lyon-3-aout-1924-xixeme-grand-prix-de-l-acf.jpg

Share this post


Link to post
Share on other sites

bet Frederick has got some very helpful material .... looking forward to his post

meantime ... noticed that the shape of the cowl above the instrument dash needed correction

so I added low temp solder to the larger opening and removed some metal from the mechanic's side - I needed more balance ..

after some fettling, I've got a more symmetric shape, which will look better with the instrument panel installed - mocked up in the last picture

and with the panel taped in place I can run the rivets over the cowl and place the instrument panel frame

the instrument dash panel will be aluminum, probably glued over the plastic sheet mock-up

 

IMG_0671.JPG

IMG_0673.JPG

IMG_0672.JPG

IMG_0675.JPG

Share this post


Link to post
Share on other sites

small update

with the instr panel located I mocked up a support post inside the body - L shaped evergreen - to locate the run of the rivets over the cowl

and of course broke another #76   - got three left .....

still a couple more rows of rivets on the body and then back to the bonnet for more .... rivets

 

IMG_0678.JPG

IMG_0679.JPG

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now