Jump to content
Model Cars Magazine Forum

Tamiya 1/24 Mazda Savanna RX-7 - 1st Generation Rotary Rocket


Italianhorses

Recommended Posts

On ‎11‎/‎22‎/‎2018 at 7:23 AM, Tommy124 said:

Fully agree. When it comes to those super-fine double lines on the hood of a '69 Camaro, I'd go for BMF aswell. And it doesn't have that "time factor" to it...

Agree here too, Dann, Tamiya is a good tape. BUT: once you use it on Tamiya acrylics or TS colors and leave it for a longer period, the solvents will leave their mark on the paint, the longer - the worse. That's why I switched to a (guaranteed) solvent-free Tesa tape for these kinds of paints...

By the way, I always use a small hairdryer on a lower temperature setting to warm up masking tape before removing it from the painted parts. This significantly reduces the tape's adhesive power on the paint - and the risk of pulling off paint instead...

That sounds like an interesting technique, Tommy!...

Link to comment
Share on other sites

On 11/22/2018 at 7:23 AM, Tommy124 said:

Fully agree. When it comes to those super-fine double lines on the hood of a '69 Camaro, I'd go for BMF aswell. And it doesn't have that "time factor" to it...

Agree here too, Dann, Tamiya is a good tape. BUT: once you use it on Tamiya acrylics or TS colors and leave it for a longer period, the solvents will leave their mark on the paint, the longer - the worse. That's why I switched to a (guaranteed) solvent-free Tesa tape for these kinds of paints...

By the way, I always use a small hairdryer on a lower temperature setting to warm up masking tape before removing it from the painted parts. This significantly reduces the tape's adhesive power on the paint - and the risk of pulling off paint instead...

Where do you get TESA tape? I have some old rolls of their cloth tape I use for seatbelts. I have not found anyplace to get it. It seems to be sold to industries only. I just realized  you are in Germany where it is made. I cannot find an online place to buy it.

 

Dscf9676.jpg

Edited by 935k3
Link to comment
Share on other sites

On 25.11.2018 at 1:00 AM, 935k3 said:

Where do you get TESA tape? I have some old rolls of their cloth tape I use for seatbelts. I have not found anyplace to get it. It seems to be sold to industries only. I just realized  you are in Germany where it is made. I cannot find an online place to buy it.

Tesa products are widely available in German DIY stores, they have dozens of different tapes for any purpose. The (solvent-free) tape I was referring to is called "Precision indoor". https://www.amazon.de/tesa-Malerband-Qualität-Promo-Pack-Rollen/dp/B00B9DDB7G/ref=sr_1_1?ie=UTF8&qid=1543234412&sr=8-1&keywords=tesa+precision+indoor

Tesa cloth tape shouldn't be a problem though, found it on Ebay.com...

Link to comment
Share on other sites

On 11/24/2018 at 4:47 PM, Luc Janssens said:

So went to my parrents today and it was quite a search on the attic to find the model, anyway as I wrote originally built in '77 or 78, then after a few year playing with it, it got a color coat and decals I probably got from a defective kit at Verlindens shop model world...this one and an old Monogram 4x4 Van are the oldest built models I still have.

image.thumb.png.d72bf987a6546f994610670d3474af48.png

 

image.png

This is awesome! Keeping as is for the memories or rebuild?

Link to comment
Share on other sites

On 11/24/2018 at 10:20 PM, Daxman said:

I love the color!

I've always wanted to wire up LED lights. I need to look into it. That looks amazing.

These are actually light bulbs that came in the kit (this is box-stock build after all :)), not LEDs, but same principle, I guess. LEDs are better since they won't get warm as these bulbs do!

Link to comment
Share on other sites

On ‎11‎/‎24‎/‎2018 at 7:00 PM, 935k3 said:

Where do you get TESA tape? I have some old rolls of their cloth tape I use for seatbelts. I have not found anyplace to get it. It seems to be sold to industries only. I just realized  you are in Germany where it is made. I cannot find an online place to buy it.

 

Dscf9676.jpg

It looks great!, but the only problem I see, is the cut edge being a frayed white line.....that would drive me nuts...lol

Link to comment
Share on other sites

16 hours ago, Dann Tier said:

It looks great!, but the only problem I see, is the cut edge being a frayed white line...

Agree with you Dann. Plus I think the structure and thickness of the tape in use is a bit out of scale. I use white Leucosilk tape (medical tape for fixing bandages etc.) and color that up using a marker. Very easy to do. https://www.voelkner.de/products/266758/Soehngen-1009210-Leukosilk-5m-x-2-50cm.html

Edited by Tommy124
Link to comment
Share on other sites

  • 8 months later...

Its been a while, huh? Finally, an update on this one…

As some of you remember, this was started as strictly box-stock project for a contest but wasn’t finished in time. Since box stock was no longer a requirement, I decided to spice it up a bit.

Originally interior was supposed to be plain tan, so the tub was carefully masked and painted base color.

48485709717_9119316750_c.jpg

The rest of the interior panels was cleaned up and painted as well:

48485550996_1348e67273_c.jpg

Real car had some sort of plaid pattern on the seats, but replicating that would have been next to impossible with paint and I didn’t want to mess with designing and printing my own for a project that started as a simple box-stock build:

https://www.rx7club.com/attachments/1st-generation-specific-1979-1985-18/67500d1091087598-picture-request-sa22c-w-plaid-inteior-zzztttooo-img600x450-1085891053z04-149n.jpg[/img]

So, I cheated. Looked high and low for some similar pattern decals but couldn’t find any. So, I bought this plaid pattern decals for nails, it was a nice design and a similar color-scheme:

48485550956_c77dc408af_c.jpg

When they showed up, they were super glossy, self-made decals – I almost threw them in the trash as I wasn’t sure I could use them. They were also too small, and that meant I had to piece them up to cover both real and front seats. But decided to give it a try:

48485550681_e40b82f714_c.jpg

48485709437_471fb42a79_c.jpg

It turned out ok with lots of setting solution, and several coats of dull-coat to get rid of the shine. Here are couple more pictures with different lighting:

48485709512_97a332f0aa_c.jpg

48485709532_705e8d5dc9_c.jpg

Dashboard was also painted, detailed, and assembled:

48485550756_bb401ae0d3_c.jpg

Since original kit does not provide any gauge cluster decals, I decided to see what could be done about it. I knew that Revell did a RX7 kit, so I found a decal sheet from that kit on ebay and bought it. I figured I could also use decals for the badges, and wheel centers from it. Side not – Revell makes terrible decals.

48485709612_82ee776a88_c.jpg

But it worked fine for the gauges, and I also painted and detailed the rest of the interior panels:

48485709477_c1c3a032c6_c.jpg

48485709577_cf12c64e97_c.jpg

Toyed around with flocking the carpet, but I could not find proper color flocking to match the paint, and after mocking the interior realized that zero of that flocking job will be seen after assembly, so passed on that.

Assembled interior looks good. Wiring for the headlights is hidden under the seat and front floor panel. Door cards actually mount inside the body shell. I really feel bad for the rear passenger’s legs!

48485550596_e77189db7b_c.jpg

48485550646_7bab2cbc15_c.jpg

48485709317_204c9462ea_c.jpg

Link to comment
Share on other sites

Well, I guess nobody missed the thread after all, hehe.

Painted the wheels and exhaust parts in metallics, front suspension parts in black:

48485709247_4c76d5c3ba_c.jpg

Assembled the wheels, tires are narrower than the rims, and I suspect the rims are also a bit oversized – but they look fine:

48485709202_ca82bd65c6_c.jpg

Soldered the wires for the headlights to the power source, put the wheels on, and married the body to the chassis:

48505970147_20af5686e0_c.jpg

Didn’t want to spend much time with the underside, just dry brushed here and there – its mostly incorrect anyway so decided this should do just fine.

48505803071_0b5380440a_c.jpg

48505803111_555f3ef8ca_c.jpg

48505797771_530abed03b_c.jpg

Everything seemed to be in its place after assembly, but somehow the headlights do not sit flush with the body anymore!

48505797806_c225d758b5_c.jpg

I’ll have to figure this one out and see what needs to be adjusted. But they work just fine, so does the motor!

48505970022_4635eb0800_c.jpg

Overall, its taking shape, good stance too!

48505970117_d475f74db1_c.jpg

48505970062_d9e57740d3_c.jpg 

Link to comment
Share on other sites

35 minutes ago, Curt said:

Beautiful little "Rotary Rocket", Alex!  The working lights look like the real thing.  Now to add the fender mounted mirrors...

Oh, there is still plenty missing here...But I'm actually finishing it up as I type this, so should be done pretty soon!

Link to comment
Share on other sites

10 hours ago, Jonathan said:

Absolutely beautiful work!

Thank you!

10 hours ago, WizPorsche944 said:

Wow ! Do the pop up lights work off the motor ?

Nah, there is a tiny lever that you pull to pop them up, and press to lower them back in.

10 hours ago, CabDriver said:

I always enjoy seeing your work Alex, and would like to see it more regularly ???

Super clean and nicely done build as always - I like the interior and that color is great!  

Thanks. Hopefully I can contribute more often!

Link to comment
Share on other sites

On 8/12/2019 at 5:58 PM, FabbricaP said:

Stunning build. Love those plaid seats!

Thanks!

All right, I think its time to wrap this project up.
Headlights and inner fenders were adjusted slightly to allow for the light to go down flush with the bonnet again:

48533792377_b9a1f08f5a_c.jpg

Works in the raised/lit up position as well!

48533637811_41ae168580_c.jpg

Badges and license plate was taken from Revell decal sheet. Taillights painted with Tamiya clears and foil backing:

48533637781_c4768d3f1d_c.jpg

One interesting part is that there is a hole under the orange part of the taillight where the latch would go. Had to stick the foil right behind that piece:

48533637586_6e052a29a2_c.jpg

Wipers, badges, wheel caps, mirrors:

48533637636_5354e735f1_c.jpg

And its all done! Full photoset in the gallery soon!

48533793042_a28b0240a9_c.jpg

48533634006_21e1bbd5ae_c.jpg

48533633956_8299f9c460_c.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...