Plastheniker Posted April 15, 2019 Share Posted April 15, 2019 Hi, after finishing my topic 1935 Auburn Speedster - The Abysmal Lindberg/Pyro Kit Completely Reworked http://www.modelcarsmag.com/forums/topic/125494-1935-auburn-speedster-the-abysmal-lindbergpyro-kit-completely-reworked/ it was clear that my Auburn Speedster and a future model of the equally iconic Cord 812 would have to stand side by side (as close relatives so to speak) in my display cabinet. Considering that the Monogram kit of the Cord 812 is more than 50 years old its quality is really outstanding. Nevertheless when building the kit some improvements are necessary IMO: The characteristic chrome trim on the bonnet is omitted and should be added if at all possible The fit of the headlight covers should be reworked The kit tires have no reasonable tread Following the assembly instructions leaves a salient gap between body and rear valance (part #52) because the rear bumper support and the chassis are moulded as one single part. Cutting off the rear bumper support from the chassis, closing the gap and fixing the rear bumper support later as a separate part is a better solution. The moulded wipers don't look convincing IMO the surfaces of the flexible exhaust heat protection tubes look too smooth Many Cords show a pair of typically shaped fog lamps not replicated in the kit The chrome trim on the soft top should be added Regarding the interior at least the moulded door handles/windowcranks and the clumsy horn ring should be replaced On the real car the lowered side windows still show the upper edge of their chromed window frames but the model's door tops don't even have slots for side windows The real car has chromed wheel covers with (fake ventilation?) holes. On the model these holes are shallow and rather vague, so drilling them out looks much better than accentuating them with black paint This said in marked contrast to the abysmal Lindberg/Pyro Cord this inexpensive kit is still highly recommendable and deserves to be reissued again and again. 1 Quote Link to comment Share on other sites More sharing options...
sjordan2 Posted April 15, 2019 Share Posted April 15, 2019 This could also be made into the Tom Mix parade Cord with its interesting cowboy touches. It’s also a good reference for converting the AMT 1/12 2-seater into a cabriolet with a back seat (cut away the convertible storage panel seam, make a back seat and make some simple cuts on the top for the rear vent windows; otherwise, the body and wheelbase are the same). Quote Link to comment Share on other sites More sharing options...
Classicgas Posted April 15, 2019 Share Posted April 15, 2019 Simply stunning. Quote Link to comment Share on other sites More sharing options...
Richard Bartrop Posted April 15, 2019 Share Posted April 15, 2019 Very nicely done, and how little you actually had to do to it speaks volume about how good the kit really is. Quote Link to comment Share on other sites More sharing options...
89AKurt Posted April 15, 2019 Share Posted April 15, 2019 Awesome summary, and model build! Hope I can find this thread later, if I ever get around to building Tom Mix's Cord. Quote Link to comment Share on other sites More sharing options...
echo Posted April 16, 2019 Share Posted April 16, 2019 You did really nice work to make the model stand out. Exceptional model. Quote Link to comment Share on other sites More sharing options...
robertw Posted April 16, 2019 Share Posted April 16, 2019 That looks nice. It makes me want to dig mine out of the stash and start it right now rather then later. Quote Link to comment Share on other sites More sharing options...
peekay Posted April 16, 2019 Share Posted April 16, 2019 Outstanding work as always, Jürgen. I love the colour and all the improvements you've made. Monogram's 1941 Lincoln is also a great kit from this series - similar quality to the Cord kit. Quote Link to comment Share on other sites More sharing options...
David G. Posted April 16, 2019 Share Posted April 16, 2019 Beautifully done Jürgen. I'm always impressed by your work. David G. Quote Link to comment Share on other sites More sharing options...
ChrisR Posted April 16, 2019 Share Posted April 16, 2019 Awesome! Quote Link to comment Share on other sites More sharing options...
Matt Bacon Posted April 16, 2019 Share Posted April 16, 2019 That looks brilliant, as ever Jurgen. An Art Deco classic, for sure. How did you do the flexible exhaust tubing? And how does the real thing breathe? Are there some actual slots somewhere in the gaps between that chrome "grille" trim? Great job, and I love the colour... best, M. Quote Link to comment Share on other sites More sharing options...
ewetwo Posted April 16, 2019 Share Posted April 16, 2019 Beautiful! Quote Link to comment Share on other sites More sharing options...
mredjr Posted April 16, 2019 Share Posted April 16, 2019 Great job!! Quote Link to comment Share on other sites More sharing options...
Richard Bartrop Posted April 16, 2019 Share Posted April 16, 2019 2 hours ago, Matt Bacon said: That looks brilliant, as ever Jurgen. An Art Deco classic, for sure. How did you do the flexible exhaust tubing? And how does the real thing breathe? Are there some actual slots somewhere in the gaps between that chrome "grille" trim? Great job, and I love the colour... best, M. Yep, those slats are what are supposed to ventilate the engine compartment. Even so, overheating was an issue. Quote Link to comment Share on other sites More sharing options...
stevehansen Posted April 16, 2019 Share Posted April 16, 2019 Beautiful job on a beautiful car!!! Quote Link to comment Share on other sites More sharing options...
1959scudetto Posted April 16, 2019 Share Posted April 16, 2019 12 minutes ago, stevehansen said: Beautiful job on a beautiful car!!! x 2 : Excellent build as always, Jürgen ! Quote Link to comment Share on other sites More sharing options...
Plastheniker Posted April 16, 2019 Author Share Posted April 16, 2019 Thanks for the comments so far! 7 hours ago, Matt Bacon said: That looks brilliant, as ever Jurgen. An Art Deco classic, for sure. How did you do the flexible exhaust tubing? And how does the real thing breathe? Are there some actual slots somewhere in the gaps between that chrome "grille" trim? Great job, and I love the colour... best, M. Yes there are ventilation slots but on almost all pictures they are invisible except on this one: Replicating flexible exhaust tubes is quick and easy: The cores of the four exhaust pipe tubes were bent from 3(?)mm soldering wire. I rolled 0.5 or 0.8mm soldering wire and wrapped this flat wire round the cores. After aligning the flat wire I secured it with very litle super glue where it was least visible. Last I polished everything with metal polish; leaving the dark polish residue in the wire gaps adds more depth. That is all. There are two ways to roll soldering wire: You can improvise an inexpensive rolling device usuable for rather thin soldering wire by fixing a small, hard wheel (hard plastic or metal, available at hardware/house improvement stores) under a piece of chip board. With the weight of your body roll over the soldering wire on a hard surface and you get a thin, bright, very flexible strip of metal that can be glued easily with super glue. Rolled wires of any kind, i. e. also thicker soldering wire, brass and copper wire, so-called silver wire, even hypodermic needles, are extremely useful for numberless purposes when detailing, converting and scratch building. I used them on virtually all models during the past 20 years. For making rolled wires of exact thicknesses/widths I made one of the best investments of my modeling life. It is called bending machine. It is meant originally for making equal, kink-free curves in sheet and strip stock. When I bought mine I was not sure if the considerable amount of money would pay off. It really did. Quote Link to comment Share on other sites More sharing options...
Peter Lombardo Posted April 17, 2019 Share Posted April 17, 2019 Yeah, this is a very well done build, just beautiful in every way considering the sad condition of the kit...... such an important car in the evolution of the automobile deserves a first rate kit.... at least you made this kit into a model worth celebrating . Very nice ....... p.s., love the color. Quote Link to comment Share on other sites More sharing options...
NOBLNG Posted April 17, 2019 Share Posted April 17, 2019 On 4/15/2019 at 10:31 PM, robertw said: That looks nice. It makes me want to dig mine out of the stash and start it right now rather then later. Yes, Thanks for posting this Jürgen. You did a beautiful job and I appreciate the tips! I recently bought this kit at a flea market and It just moved up in the priority list. Quote Link to comment Share on other sites More sharing options...
Dominik Posted April 17, 2019 Share Posted April 17, 2019 On 16.04.2019 at 5:31 AM, robertw said: That looks nice. It makes me want to dig mine out of the stash and start it right now rather then later. agreed. One of my very old builds waiting for a Restauration. really really beautiful and in my view perfect! Quote Link to comment Share on other sites More sharing options...
ChrisBcritter Posted April 17, 2019 Share Posted April 17, 2019 (edited) My late father's favorite car, ever since he saw one in Paducah, KY as a boy. He built the Monogram kit back in the '60s which I still have. After all these years, I never noticed the lack of windows in the doors! Beautiful job, Jürgen. On 4/15/2019 at 2:29 PM, Plastheniker said: The real car has chromed wheel covers with (fake ventilation?) holes. Real ventilation holes; they line up with holes on the wheels. Edited April 17, 2019 by ChrisBcritter Quote Link to comment Share on other sites More sharing options...
Jim N Posted April 17, 2019 Share Posted April 17, 2019 Great job. Really spectacular work! Quote Link to comment Share on other sites More sharing options...
tkzwolf Posted April 18, 2019 Share Posted April 18, 2019 Gorgeous! Quote Link to comment Share on other sites More sharing options...
olschoolkid Posted April 18, 2019 Share Posted April 18, 2019 Very nice build. I think these Cords were beautiful cars and you should certainly built an excellent example. Quote Link to comment Share on other sites More sharing options...
thatz4u Posted April 18, 2019 Share Posted April 18, 2019 Nice old "coffin nose", love the color... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.