1320wayne Posted September 16, 2019 Share Posted September 16, 2019 (edited) It's time for change of pace. I've had this plan in my head for some time now and I'm ready to get started. I'm building a Rat Rod Rollback using a Jimmy Flintstone rat rod Peterbilt body as the base. The resin body comes with the interior, seats, and grill. The tires and wheels are also resin items. They were some extras from a resin cast 67 Dodge crew cab that I have for a future build. The rollback bed is from a diecast piece. The chassis is being kitbashed from multiple kits including an A100 and an F350 dually. The engine will be a 413. Edited September 16, 2019 by 1320wayne Quote Link to comment Share on other sites More sharing options...
Jantrix Posted September 17, 2019 Share Posted September 17, 2019 I will be following this. I've been planning a rollback for a while, but it will end up being larger than any display case I own. Looking forward to seeing where you take this. Quote Link to comment Share on other sites More sharing options...
espo Posted September 17, 2019 Share Posted September 17, 2019 This is going to be fun to watch. Quote Link to comment Share on other sites More sharing options...
gotnitro? Posted September 17, 2019 Share Posted September 17, 2019 Interesting.. Quote Link to comment Share on other sites More sharing options...
misterNNL Posted September 17, 2019 Share Posted September 17, 2019 Just off the rails enough to catch my eye. Looks very promising. I might have to pick up one of those bodies from JF and place the turbo 5.9 Cummins I have between the rear frame rails.(like I need another project eroding my brain and cluttering my stash!) Quote Link to comment Share on other sites More sharing options...
1320wayne Posted September 19, 2019 Author Share Posted September 19, 2019 More progress on the rollback. The chassis kitbash is coming along. Lots of saved parts from different sources. One good reason to never throw anything away. I also never throw away used pens because they can serve so many model building purposes. In this case I'm using two old bic pens for my exhaust stacks because the diameter is perfect and after cutting away the pen piece the tapered area makes for a perfect transition to the rest of the exhaust. I also extended the nose, which will eventually be made into a tilt nose. Quote Link to comment Share on other sites More sharing options...
misterNNL Posted September 20, 2019 Share Posted September 20, 2019 You might consider picking up the chopped Hummer that JF offers as a load for this project. That'd be very cool. Quote Link to comment Share on other sites More sharing options...
PatW Posted September 21, 2019 Share Posted September 21, 2019 Super job! Keep up the good work! Quote Link to comment Share on other sites More sharing options...
LouO Posted September 21, 2019 Share Posted September 21, 2019 Now this is going to very cool! Quote Link to comment Share on other sites More sharing options...
gotnitro? Posted September 22, 2019 Share Posted September 22, 2019 Nice work Quote Link to comment Share on other sites More sharing options...
DaveP Posted September 22, 2019 Share Posted September 22, 2019 Cool, did you extend the body yourself or purchase it like that? Quote Link to comment Share on other sites More sharing options...
1320wayne Posted September 23, 2019 Author Share Posted September 23, 2019 15 hours ago, DaveP said: Cool, did you extend the body yourself or purchase it like that? It comes like this. Quote Link to comment Share on other sites More sharing options...
1320wayne Posted September 23, 2019 Author Share Posted September 23, 2019 A few more small updates. I scratchbuilt a headache rack out of brass and styrene. It will also be used to mount the exhaust stacks as well as a light bar on top. I cut away the front end to figure out where to hinge it at. And I pulled out a 3d printed roof rack that I recently purchased, not knowing where I was going to use it. Now I know. Quote Link to comment Share on other sites More sharing options...
Modelbuilder Mark Posted September 23, 2019 Share Posted September 23, 2019 Eager to see where this goes. Quote Link to comment Share on other sites More sharing options...
1320wayne Posted September 26, 2019 Author Share Posted September 26, 2019 A bit more. Started on the framework for the rollback bed, got some primer on the bed and stacks and decided that the light bar would best fit on the cab. Quote Link to comment Share on other sites More sharing options...
lou s Posted September 27, 2019 Share Posted September 27, 2019 I like it ? Quote Link to comment Share on other sites More sharing options...
misterNNL Posted September 28, 2019 Share Posted September 28, 2019 On 9/22/2019 at 11:03 PM, 1320wayne said: A few more small updates. I scratchbuilt a headache rack out of brass and styrene. It will also be used to mount the exhaust stacks as well as a light bar on top. I cut away the front end to figure out where to hinge it at. And I pulled out a 3d printed roof rack that I recently purchased, not knowing where I was going to use it. Now I know. You might consider adding some steps up the back cab wall to access the roof storage rack and some accessory flood lighting for night recovery work. Quote Link to comment Share on other sites More sharing options...
1320wayne Posted September 30, 2019 Author Share Posted September 30, 2019 Working on the operating mechanism for the sliding and tilting bed. Quote Link to comment Share on other sites More sharing options...
wesa508 Posted October 4, 2019 Share Posted October 4, 2019 I noticed on an old post that at one time you made a set of resin Super Pak parts for the 1977 Plymouth Volare Roadrunner. Do you still make those? I would definitely like to buy a set or two if you do. Quote Link to comment Share on other sites More sharing options...
1320wayne Posted October 6, 2019 Author Share Posted October 6, 2019 On 10/4/2019 at 12:53 PM, wesa508 said: I noticed on an old post that at one time you made a set of resin Super Pak parts for the 1977 Plymouth Volare Roadrunner. Do you still make those? I would definitely like to buy a set or two if you do. Not me. Quote Link to comment Share on other sites More sharing options...
1320wayne Posted October 6, 2019 Author Share Posted October 6, 2019 More updates. Tires and wheels are painted and installed. Chassis has base color paint on it. Still need to weather detail it. Scratchbuilt running boards along with creating the tilt nose hinge and cut out the grill for added mesh grill. Also added a resin cast skull hood pull. Quote Link to comment Share on other sites More sharing options...
misterNNL Posted October 8, 2019 Share Posted October 8, 2019 On 9/19/2019 at 10:22 AM, 1320wayne said: More progress on the rollback. The chassis kitbash is coming along. Lots of saved parts from different sources. One good reason to never throw anything away. I also never throw away used pens because they can serve so many model building purposes. In this case I'm using two old bic pens for my exhaust stacks because the diameter is perfect and after cutting away the pen piece the tapered area makes for a perfect transition to the rest of the exhaust. I also extended the nose, which will eventually be made into a tilt nose. Did I notice that the whole rear frame and suspension section was flipped over in this sequence of photos? It dos look better that way, and much stronger. Quote Link to comment Share on other sites More sharing options...
1320wayne Posted October 13, 2019 Author Share Posted October 13, 2019 Got some paint and decals on the cab. I never throw anything away because you never know when it might come be useful. In this case some material from an old VCR that resembles scale expanded metal. I cut a piece to size for the headache rack along with making running board tread with the same material. I also scratchbuilt a front bumper. And a visor from the parts box. Quote Link to comment Share on other sites More sharing options...
espo Posted October 14, 2019 Share Posted October 14, 2019 This just keeps getting better all the time. What part of the VCR did you use for the Headache Rack ? Quote Link to comment Share on other sites More sharing options...
1320wayne Posted October 14, 2019 Author Share Posted October 14, 2019 8 minutes ago, espo said: This just keeps getting better all the time. What part of the VCR did you use for the Headache Rack ? The headache rack was made out of brass. The material that looks like expanded metal came from the VCR. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.