mirage1980 Posted November 14, 2019 Share Posted November 14, 2019 Hi i'm a italian modeller end i decided to modify a Pocher F40 model and imagine how it could be today. The main muse is a revisitation of the F40 designed by designer Samir Sadikhov. My intention is to maintain almost all of the pocher kit, modifying it to make it similar to the designer's project, similar because I will also use mine. Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 this is the scrap, given to me, from where I started. Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 cutting work begins  the works on the front proceed, the shapes become more and more similar to those of the drawing, however, I decided to leave the two air intakes on the hood instead of one as proposed by the designer ...   Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 I continue to give the new shapes on the upper part of the front hood, I gave the first coat of putty and sanded.  I cut across the highlighted points  Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 once the general lines are obtained, the crowning works begin. As a method I adopt the system of applying brass rods to have the curvature guidelines, by doing so sanding I will have the curve line as a reference . in the fenders I remove the excess from the inside ... Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 I continue to model... Â Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 I started to rebuild the lower part of the front, again with the brass rod technique I found the right curve by welding the two ends (with cyan and bicarbonate) in the same point ... Â Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 here I dedicated myself to the wheel arch radius considering the new wheel footprint and also calculating the new ground clearance. Â I gave the first draft on the front, at the end I will mount the carbon splitter that I will realize once I finish modeling the whole body ... Â Â Â Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 I made the small central ribs. The procedure is always that of the rough coat with reference brass rod and final application of plasticard from 0.3. it's just sketched  Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 I continue to sketch the sides.. ... I welded the bonnet because of the shapes the gas filler will be on the top so only the inner part will open. Then the usual technique with the brass rod to recreate the shapes. Â ... to finish I recreated the side of the wing with cyan + bicarbonate ... resistance test of the compound. Â Â Â Â Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 I sketched the new lines of the hood ... I continue to give the shapes, today's work has consisted of giving harmony, with the right ribs, to the roof and the bonnet .. Â Â Â Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 (edited) I started to shape the back ... I continue to form the back, for this part I used a profile for pvc tiles that has the right camber that I needed, and then adapt it to the model ... Â Â Â Â Edited November 14, 2019 by mirage1980 Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 Â I recreated the housing for the drains... I continue to sketch the back... Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 first coat of putty ... Meanwhile today I have finished giving the shapes and the lateral ribs with the usual technique of the brass rod, it was quite difficult to make the two equal sides because unlike the front bonnet there is the obstacle of the passenger compartment ... Â Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 I modeled the side panels this is the final shape. Â Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 (edited) I continue to sketch the back... first coat of putty ... Â Â Â Edited November 14, 2019 by mirage1980 Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 14, 2019 Author Share Posted November 14, 2019 Meanwhile today I have finished giving the shapes and the lateral ribs with the usual technique of the brass rod, it was quite difficult to make the two equal sides because unlike the front bonnet there is the obstacle of the passenger compartment ... Â Quote Link to comment Share on other sites More sharing options...
avidinha Posted November 16, 2019 Share Posted November 16, 2019 Very impressive work so far. Can't say that I'd be brave enough to cut up such an expensive model. Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 16, 2019 Author Share Posted November 16, 2019 Thanks, it was a model that gave me a lot of damage. Seeing that tribute was love at first sight ... Quote Link to comment Share on other sites More sharing options...
Codi Posted November 17, 2019 Share Posted November 17, 2019 First let me say simply "grazi" Luca for posting here and sharing your talents. The photos / explanations you've shared are simply phenomenal.  I love to scratch build but this is talent beyond anything I possess.   Will certainly follow along as you progress.  Cheers, Tim Quote Link to comment Share on other sites More sharing options...
iamsuperdan Posted November 17, 2019 Share Posted November 17, 2019 Most impressive. Looking forward to more updates! Quote Link to comment Share on other sites More sharing options...
Deuces Posted November 18, 2019 Share Posted November 18, 2019 Where in Italy are you from????..... I was born in a little town called Arpino..... Quote Link to comment Share on other sites More sharing options...
bobthehobbyguy Posted November 18, 2019 Share Posted November 18, 2019 Impressive work. Great start. Very ambitious project. Fantastic body work. Quote Link to comment Share on other sites More sharing options...
wisdonm Posted November 18, 2019 Share Posted November 18, 2019 Very impressive scratching. How do you control the thickness of your cyan + bicarbonate parts? Quote Link to comment Share on other sites More sharing options...
mirage1980 Posted November 18, 2019 Author Share Posted November 18, 2019 thanks to all of you guys, actually I'm ahead with the work, today I have some time to post the progress so as to align myself with the current state. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.