Brutalform Posted February 14, 2020 Share Posted February 14, 2020 (edited) Got bored with the 65 Galaxie. Just not feeling it, so back on the shelf it goes. Couldn’t wait to get started on this Moebius AWB. I plan to add a little more detail to the Hilborn injection system, using some black wire. I’m using this photo from the Max Perf book, as a reference. This system will use the long tubes, because from what I’ve read, the long tubes were used on the automatic cars, and the short on the four speeds. Smiths car started out as a four speed, so this is the route I’m taking. Edited February 14, 2020 by Brutalform Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 14, 2020 Author Share Posted February 14, 2020 I drilled the manifold fuel block so I can run fuel lines to each separate tube, and a main fuel supply line to the under hood fuel tank. After the holes were drilled in the tubes, each line will get a hollow bolt head, where the line fits the tube. That will be later as I do the engine final assembly. Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 14, 2020 Author Share Posted February 14, 2020 Body has the panel lines deepened, primed and painted Tamiya Pure White. After masking is done Tamiya Deep Metallic Blue will be laid down. No clear, as I read these cars weren’t perfect looking “show cars”. Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 14, 2020 Author Share Posted February 14, 2020 Wanted to use a PE grill, so you can see through the front just like the 1:1 car. So I had to cut some of the stock grill piece out. More later... Quote Link to comment Share on other sites More sharing options...
'70 Grande Posted February 14, 2020 Share Posted February 14, 2020 I, (like many), will be watching this one closely! You're off to a great start! Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 14, 2020 Author Share Posted February 14, 2020 Also got the wheels done. These are the decals I’ll be using. Quote Link to comment Share on other sites More sharing options...
250 Testa Rossa Posted February 14, 2020 Share Posted February 14, 2020 Looking good! Quote Link to comment Share on other sites More sharing options...
wrenchr Posted February 14, 2020 Share Posted February 14, 2020 Nice, that grill looks looks killer, going to need to get 1 or 5 of those. Quote Link to comment Share on other sites More sharing options...
High octane Posted February 14, 2020 Share Posted February 14, 2020 Great project Tom as I just love dem Mopars! Quote Link to comment Share on other sites More sharing options...
espo Posted February 14, 2020 Share Posted February 14, 2020 I like the subject of your build. I have two questions for you. You have done your research on this and my question has to do with the doors. Your picture of the real car shows what looks to me anyway is that the drivers door is a sedan door. I'm looking at the white colored metal surrounding the glass. The roof is a Hardtop Roof and the quarter side glass looks like a Hardtop glass and the rear portion of the roof is definitely a Hardtop in shape. As I recall many of these cars were cobbled together with what ever they may have had around the shop. While looking at your new grill, and realizing your still mocking up things at this point, the grill looks flat and the 1:1 grill was raised at the center bar and curved back from there to the top and bottom edge of the grill. opening. The wheels look good and I like your engine and fuel injection set up. Quote Link to comment Share on other sites More sharing options...
afx Posted February 14, 2020 Share Posted February 14, 2020 Is the PE grille come in the kit or is it aftermarket? Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 14, 2020 Author Share Posted February 14, 2020 Thanks everyone. JC the PE parts are from MCG. David, the grill will bend very easily to resemble the real grill. I notice on the real car there is a body color support directly behind the center of the grill. Right now, I am painstakingly removing the center from the kit supplied grill, trying to get the chrome trim that surrounds the grill off in one piece. Hopefully if it all works out as planned, it will hold the PE grill in place, acting like a frame. Good thing I have a couple extras lying around just in case this one gets messed up. As for the door trim, there is a piece molded in the clear side window that separates the door and rear glass. It could be painted white to match the car, and then add some strip styrene around the top. Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 14, 2020 Author Share Posted February 14, 2020 A couple of pics to better explain... Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 14, 2020 Author Share Posted February 14, 2020 Got the kit grill separated from the trim. Now just a little more cleaning up with a file, and getting the grill slightly bent like the on the car. Quote Link to comment Share on other sites More sharing options...
gtx6970 Posted February 15, 2020 Share Posted February 15, 2020 Tuned in Quote Link to comment Share on other sites More sharing options...
250 Testa Rossa Posted February 16, 2020 Share Posted February 16, 2020 Looks awesome! Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 18, 2020 Author Share Posted February 18, 2020 Did very little on the AWB. I didn’t realize I didn’t have anymore racing harnesses for the interior. I ordered a few sets from ProTech, for this and the other couple AWB cars I plan on building. Got the roll bar built and cut apart the dash, at least. Quote Link to comment Share on other sites More sharing options...
swede70 Posted February 19, 2020 Share Posted February 19, 2020 It looks real nice - very trim. Thanks for sharing... Mike K./Swede70 Quote Link to comment Share on other sites More sharing options...
slusher Posted February 19, 2020 Share Posted February 19, 2020 Really nice work! Quote Link to comment Share on other sites More sharing options...
dino246gt Posted February 19, 2020 Share Posted February 19, 2020 Aww.... I wanna see more!!! I love this project! Quote Link to comment Share on other sites More sharing options...
1320wayne Posted February 20, 2020 Share Posted February 20, 2020 Your progress looks great. You are also correct in that this was a 4 speed car. I see that your color choice is deep metallic blue. The actual color on the car was a teal blue color. Dupli-color BGM0440 Bright Aqua Metallic is an almost perfect match. Quote Link to comment Share on other sites More sharing options...
1320wayne Posted February 20, 2020 Share Posted February 20, 2020 Also, there is a seller on Ebay that I've purchased many decals from. Very reputable seller. I believe he goes by the name of Repols. He does a much better set of decals for this car. Fremont decals are good but this other set has the correct foil lettering, pinstripes, correct colors and the message that is printed across the trunk. Quote Link to comment Share on other sites More sharing options...
Draggon Posted February 20, 2020 Share Posted February 20, 2020 Chris Walsh is rpols6. He has a facebook page too. Good guy. https://www.facebook.com/groups/1859313104091231/ https://www.ebay.com/sch/rpols6/m.html?_nkw=&_armrs=1&_ipg=&_from= Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 21, 2020 Author Share Posted February 21, 2020 (edited) 21 hours ago, 1320wayne said: Also, there is a seller on Ebay that I've purchased many decals from. Very reputable seller. I believe he goes by the name of Repols. He does a much better set of decals for this car. Fremont decals are good but this other set has the correct foil lettering, pinstripes, correct colors and the message that is printed across the trunk. I wish I knew about these decals. I had the car masked originally to have the front fenders and hood remain white, just like the 1:1car. Then I realized these decals I bought don’t have any of the gold foil trim. So I decided to just paint the fenders and tip of the hood all blue. It would have looked bad without the gold trim to separate the white and blue. Your decals even has the “Plymouth” for the hood and mine does not. Oh well... In to the purple pond it will go, if I can score these decals. Probably will end up cutting the Hilborn tubes, and building the stick shift version. Edited February 21, 2020 by Brutalform Quote Link to comment Share on other sites More sharing options...
Brutalform Posted February 21, 2020 Author Share Posted February 21, 2020 Didn’t see any on the Bay, and I don’t have FB. I messaged the seller to see if he could help me out. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.