Scale-Master Posted June 25, 2022 Share Posted June 25, 2022 (edited) 1991 Le Mans winner. This is a 1/87th scale LeMans Miniatures resin kit produced in '91. The bodies on all the kits in this series I've seen were pre-painted, which makes touch up of the fluorescent colors a bit of a challenge. (And it does need touching up.) The kit is packaged like a multi-blister Hot Wheels card and the clear vacuum formed plastic was super brittle. So the first step for me was to cut out the windows and headlight covers from the exact same material to see where that went. Thankfully the kits usually provide two sets of those parts. The clear was equally brittle as the packaging and the windshield split in two places while I was cutting the side windows out. So I used the second pull for the windshield. The headlight covers were surprisingly the easier parts to trim to fit. Before installing the clear parts the interior and headlight buckets needed to be painted. The clear fits pretty well especially considering the size. The kit even provides a decal for the dashboard. Edited July 2, 2022 by Scale-Master Quote Link to comment Share on other sites More sharing options...
Pierre Rivard Posted June 25, 2022 Share Posted June 25, 2022 Decal? I can't even see the dashboard! 1/87 scale...brave man 1 Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted June 26, 2022 Author Share Posted June 26, 2022 The tires are soft and rubbery, which on the other cars I've built in this series works out as a nice feature. But these rims are a larger diameter and the tires look to be the same stock as used on the smaller wheels. Unfortunately they don't stay concentrically round when stretched over the wheels. Additionally they began to split after being on the rims overnight. So I machined a new set of tires. 2 Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted June 26, 2022 Author Share Posted June 26, 2022 The resin wheel centers for the front fit very well. The photo-etched rears on the other hand took a good amount of sanding and shaving of the rims to fit as deep into the rims as they should. Decals are provided for the fronts. The Dunlop tire lettering is included too. Quote Link to comment Share on other sites More sharing options...
absmiami Posted June 26, 2022 Share Posted June 26, 2022 Don’t sneeze ! 1 Quote Link to comment Share on other sites More sharing options...
Pierre Rivard Posted June 26, 2022 Share Posted June 26, 2022 Don't even breathe! 1 Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted June 28, 2022 Author Share Posted June 28, 2022 This is the first decal for the body graphics. It took about 30 minutes to apply. 1 Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted June 28, 2022 Author Share Posted June 28, 2022 Four more decals applied. A good 90 minutes for them. The two around the headlights were more work than the first one. There are a few nice little PE parts for the rear end. This is the first to be installed. I still need to trim/touch up the decal before fitting the Gurney flap. Quote Link to comment Share on other sites More sharing options...
drodg Posted June 29, 2022 Share Posted June 29, 2022 Well 1:43 is hard to work with because of the size of parts and quite frankly my eyesight at 65. I cannot imagine building this and you are doing an excellent job. 1 Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted June 29, 2022 Author Share Posted June 29, 2022 The two side graphic decals were laid out on the sheet on the wrong sides. The other decals are laid out on the sheet as they should go onto the car. After a little head scratching I figured it out. These were even more difficult to get to conform than the previous ones. Even on the correct sides, they were a bit short in the rear areas. Fortunately the kit includes a small section of green decal to patch with. It also provides a section of white dotted lines. It took two pieces of the green to fix each side. 2 Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted June 30, 2022 Author Share Posted June 30, 2022 The rear wing is PE, I think it's maybe made of nickel, it is not brass. It comes pre-stamped to give it an airfoil of sorts. The wing tips are brass PE. All the decals have been applied. There were a couple tiny green areas that I touched up with X-28 Park Green. I was pleasantly surprised at how close it matched these decals, but then it did a good job in the same application on the Tamiya kit of the same car… Quote Link to comment Share on other sites More sharing options...
porschercr Posted June 30, 2022 Share Posted June 30, 2022 Looks good. Trevor 1 Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted June 30, 2022 Author Share Posted June 30, 2022 The interior is one piece of resin. I cemented it to the PE chassis. The steering wheel is PE too with a pin for the steering column. Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted June 30, 2022 Author Share Posted June 30, 2022 Got the wheels, Gurney flap and wing installed. There's even a little PE tow ring for the front. 1 Quote Link to comment Share on other sites More sharing options...
Scale-Master Posted July 1, 2022 Author Share Posted July 1, 2022 Those mirrors were fun… The bodies are resin and the kit provided tiny thin PE posts. The resin parts were not painted and the PE ones were, but they were very undersized so I made new posts from thin strips of styrene. I found a fluorescent orange Tamiya paint pen that did not need a white base to cover well and brush painted the mirror parts. Chrome silver paint will have to do for the mirror faces… 1 Quote Link to comment Share on other sites More sharing options...
drodg Posted July 1, 2022 Share Posted July 1, 2022 Looks great. Wow 1 Quote Link to comment Share on other sites More sharing options...
absmiami Posted July 1, 2022 Share Posted July 1, 2022 Wait - where’s the detailed four rotor engine ?? Quote Link to comment Share on other sites More sharing options...
bbowser Posted July 1, 2022 Share Posted July 1, 2022 Unbelievable, makes my head hurt just to think about it. Well done. 1 Quote Link to comment Share on other sites More sharing options...
Mattilacken Posted July 3, 2022 Share Posted July 3, 2022 Beautiful work as always master! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.