Sign in to follow this  
Followers 0

Late Model Mustang Pro Sportsman

21 posts in this topic

Posted (edited) · Report post

Hello all,

This is my first blog, it may become obvious.

Had decided to build a late model drag car some time ago and was inspired by a few that I have seen in this forum.

I started with the Revell '06 Mustang GT because it had a flat hood. I also purchased the Revell 55 Chevy Pro Sportsman kit for the running gear.

The 55's running gear required little modification to make it fit the Mustang Body, but the cage is way wrong for my app. so I am in the process of scratchbuilding my own.

I will attempt to post a few pics from time to time to show progress, if and when I figure out how to do that..

I invite all comments and suggestions as I am somewhat of a rookie.

Thanks to all....

IMG_1417.jpg

IMG_1418.jpg

IMG_1419.jpg

IMG_1420.jpg

IMG_1421.jpg

IMG_1422.jpg

IMG_1423.jpg

IMG_1424.jpg

Edited by limoman39

Share this post


Link to post
Share on other sites

Posted · Report post

Just moved this to the drag racing section.

Realized that I had started my blog where no one could get to it.

Thanks to all the tips that modelers have given to this point.

More pics soon, been working on the cage a little.

Also, will be starting to build the Ross Gibson that I bought for this piece.

Rick

Share this post


Link to post
Share on other sites

Posted · Report post

Here a few pictures of the progress for the Mustang.

Thanks to all for the great tips for how to bend the styrene for the cage.

Added the seat and some belts from Modeling by Chris.

The Ross Gibson Engine is progressing slowly. Really like the detail of this

piece but being the amateur that I am it is a difficult build.

No worry though, I don't give up easily and will prevail.

Thinking I probably should have purchased the body from Reliable. But it might turn out ok.

Maybe the next one I will go the extra mile and use the good parts.

Rick

IMG_1444.jpg

IMG_1445.jpg

IMG_1447.jpg

IMG_1448.jpg

IMG_1450.jpg

Share this post


Link to post
Share on other sites

Posted · Report post

I've been watching without comment till now. This is far from amateurish.

It's looking top notch and the Gibson motor will be a great addition. I myself haveabout 6 of them and have yet to use one. But, I have a few scratchbuilt type drag cars coming up and they will get used.

This build is coming along very nicely

Bob F

Share this post


Link to post
Share on other sites

Posted · Report post

I hope that there is going to be a FORD engine in that Mustang and not a boat anchor Chevy :D

Share this post


Link to post
Share on other sites

Posted · Report post

Nice build. Keep the first hood scoop, it looks better on that stang.

Share this post


Link to post
Share on other sites

Posted · Report post

It's all Ford thru and thru promodmerc. Just like the builder...

The reason I changed the scoop was the other did not fit up with the windshield.

I'm kinda picky... :D

I have another too, I keep switching back and forth.

Thanks for the nice comments guys.

But I really am a rookie. The Blue Corvette you see in the backround was my first build in at least 30 years.

Built those in commemoration of a friend of mine that died last year.

Working on the Gibson, and steerable front susp now.

Slow going this week, work is killing me...

Trying to keep those Fords in the winners circle.

More to come soon.

Share this post


Link to post
Share on other sites

Posted · Report post

Ok Gang,

Here are a few more shots of the Mustang.

Been working mostly on the front steering.

My 1st step was to make my spindles and springs.

I used 3/32 alum tube for the spindles and some small wire for the springs.

As you will see it took a few tries to get the look I wanted.

IMG_1467.jpg

IMG_1458.jpg

IMG_1466.jpg

IMG_1466.jpg

Then I tried to come up with some sort of rack and pinion type of tie rod.

This is my best idea to this point, it could change.....

Again I used a piece of 3/32 alum tube and ran some small flexible wire thru it.

The wire has a solid core so I bent a 90 on the end and drilled a hole in my spindle steering arm to match the wire.

So far so good, I'll let you know when I get a little further along.

IMG_1468.jpg

IMG_1469.jpg

IMG_1470.jpg

IMG_1471.jpg

As you can tell from the pictures I have not made a lot of progress on the Ross Gibson.

The yellow wires that you see off to the right of the chassis in a couple pics are the beginnings of the plug wires.

After I get this front suspension finished I would like to get that motor done and installed.

Then I can finish up with the supports for the bay bars (the cage around the motor).

I'll try to keep this moving along... Maybe cut out the trunk lid and add some detail to the rear.

Plumb the fuel cell and nitrous tanks.

Still haven't decided on a scoop for the hood or a paint scheme for the body.

Thanks for looking

Share this post


Link to post
Share on other sites

Posted · Report post

Looks good so far limo, the first scoop does look better. If it doesn't fit right, MAKE it fit, it's only plastic. looks like you need to adjust the wheelbase a tad too. Oh, an to be honest with you, you ARE supposed to put your REAL name in your sig, unless of course,your parents actually DID name you limoman. It just makes for freindlier communication. :rolleyes:B)

Share this post


Link to post
Share on other sites

Posted · Report post

Thanks George,

The name is Rick....

Had a limousine service years ago back in O hi o.

Everyone just called me that and it kinda stuck.

Outta that now a days, living the dream in the world of Nascar....

Have a great day, stop by anytime my friend,

Rick :rolleyes:

Share this post


Link to post
Share on other sites

Posted · Report post

More than welcome Rick! :D For not havein done a model inna while, your sure doin a GREAT job on this lil rascal! There aren't too many newer Mustang Pro-Stockers(at least I haven't seen many)out there. Yours looks like a 10 second machine easy!!! Don't stop now Daddy-O, she's lookeen goood! :D:D

Share this post


Link to post
Share on other sites

Posted (edited) · Report post

WOW its coming together really good I'm working two mustang kits, some what with the same thing in mind. I'm getting a one of my kits from reliable resin i cant wait to see how your stang comes out.

Edited by JOSH T

Share this post


Link to post
Share on other sites

Posted · Report post

It's all Ford thru and thru promodmerc. Just like the builder...

The reason I changed the scoop was the other did not fit up with the windshield.

I'm kinda picky... :lol:

I have another too, I keep switching back and forth.

Thanks for the nice comments guys.

But I really am a rookie. The Blue Corvette you see in the backround was my first build in at least 30 years.

Built those in commemoration of a friend of mine that died last year.

Working on the Gibson, and steerable front susp now.

Slow going this week, work is killing me...

Trying to keep those Fords in the winners circle.

More to come soon.

IMG_0208.jpg

Hi rick my name is Josh I'm alittle green to this to. But here a picture of the one I'm putting together i my self like the other scoop just a little cutting here and filing there then it went in like the factory should have put in.

Share this post


Link to post
Share on other sites

Posted · Report post

Thanks Josh,

Looks like your Mustang is coming along nicely.

I need to get back on mine after the Holiday.

Been very busy at work.

I'll post more soon....

Rick

Share this post


Link to post
Share on other sites

Posted · Report post

Really nice progress, going to be a killer build,...

Share this post


Link to post
Share on other sites

Posted · Report post

That's looking great, Rick. I love all the detail you're putting into it...

Share this post


Link to post
Share on other sites

Posted · Report post

Looking Great!!

Share this post


Link to post
Share on other sites

Posted · Report post

Thanks for the nice comments, I have changed directions again, the front suspension did not come out right when I finally got the body on the chassis. So I have made tie rods and a new front linkage system. Pics to follow.

Share this post


Link to post
Share on other sites

Posted · Report post

Very cool!

Share this post


Link to post
Share on other sites

Posted · Report post

it looks really neet

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0