skulls Posted January 18, 2012 Share Posted January 18, 2012 I am just wondering if anyone might know a way to make some sort of functional hydraulic rams, just bacically somthing that can be positionable but strong enough to stabilize some weight. I am looking to see if I can scratch build a car carrier trailer in the near future and well with all the hydraulic rams they have on those trailers I want to do the same but maybe make them strong enough to be positionable and still hold the weight of a car model on them. Thanks james Quote Link to comment Share on other sites More sharing options...
cavejohnson Posted January 18, 2012 Share Posted January 18, 2012 Hmm. I did a small replacement ram on a die cast auto transport that was 1/25th. I used some aluminum hobby tube (I guessed the size). As for making it positionable I stuffed a bit of Mystik No.2 high temp grease in the tube and that created a nice substitute. Quote Link to comment Share on other sites More sharing options...
cavejohnson Posted January 18, 2012 Share Posted January 18, 2012 (edited) I guess I should add that my setup used what looked like a piston. So when you extended it, it allowed grease to move into the bottom of the tube for support, when it was compressed it made a bit of back pressure but after a couple of seconds it would stablize. Edited January 18, 2012 by cavejohnson Quote Link to comment Share on other sites More sharing options...
Tony Bryan Posted January 18, 2012 Share Posted January 18, 2012 To have working rams is relatively easy, and to have them hold weight is also easy, here is what I have done in the past I machine the piston of the ram just a fraction smaller than the inside diameter of the cylinder than I require, then I insert a pin on each side these are then filed down to suit the cylinder, so they are a tight fit, the ram then relies on fiction to work, with some fine tuning you can get them very close to being what you want and hold the weight that you want it to hold I have made them in styrene tube, and used a drill to shape what I want them to be, (hold the parts in the chuck here is the pin that is filed down ready for a test fit, you can also machine a groove and use "O" rings as you are applying friction to the inside of the rams/cylinder Here is some better ones that I had some white metal fitting made these did hold a 600mm boom up The grease option sounds like it would be ok, but could end up messy, then again, would add some real detail, good idea there, the radio antenna, so also a great idea, but these create a lot of force on the fittings that you attach, and on the model when you are adjusting them as they are tight, the antenna has to stay up right, and are generally chrome, which is a hard surface to get glue to stay attached to The RC guys have full working hydraulics, with pumps, valve banks, and rams, they are expensive Hope this helps Quote Link to comment Share on other sites More sharing options...
skulls Posted January 19, 2012 Author Share Posted January 19, 2012 Wow, thank you so much guys for the input. Tony those rams you made look amazing, and just like everything else in this hobby, it looks like it will take a bit of time and alot more patience. Quote Link to comment Share on other sites More sharing options...
cavejohnson Posted January 19, 2012 Share Posted January 19, 2012 My setup looked a lot like Tony's, except I don't have any means to make a precise friction piston. I did have both ends sealed up and after 2 years it still works and no grease has escaped. I use that No. 2 to grease fifth wheels and then spray it to create a crust of sorts so it doesn't make a mess. Quote Link to comment Share on other sites More sharing options...
skulls Posted January 26, 2012 Author Share Posted January 26, 2012 I think I will give it a try, nows its just a matter of going to pick up some stock at the hobby shop. Again "cavejohnson" that is a really great idea with the grease, I will give it a shot and it should hold the weight that I need on it. Quote Link to comment Share on other sites More sharing options...
Truck parts Posted February 3, 2012 Share Posted February 3, 2012 The rams look great Quote Link to comment Share on other sites More sharing options...
ewaskew Posted February 3, 2012 Share Posted February 3, 2012 On real car hauler's the main support beam that the cylinder's push up and down have hole's in them. Once you have the ramp where you want it you stick the safety pin in one of those hole's and let the cylinder down until the pin bottom's out. If you do this on your model it adds detail and you don't take a chance on the cylinder's not holding the weight. Quote Link to comment Share on other sites More sharing options...
skysoldier46 Posted November 16, 2012 Share Posted November 16, 2012 I did a scratchbuilt well drilling rig that has working hydraulics for the drill tower. It's in one of the threads here, I didn't use any grease for effects tho but the tower does raise and lower with no problems. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.