Jump to content
Model Cars Magazine Forum

chevy 5700


Recommended Posts

What is going to be the final goal with the build? Replica stock? Custom? For a stock build, the Ford frame would be the closest to get a basic start. It should be noted, this cab will not build a factory 5700, there were no factory crew cabs from GM until the early '70s. It could be an aftermarket conversion, though.

To help with the dimensions, here's a few links that will help you out.

http://chevy.oldcarmanualproject.com/chevyresto/59tld11.htm

Here's the basic layout of the '55-'59 LCF chassis

http://chevy.oldcarmanualproject.com/shop/1955truck2/55ctsm0012.htm

More frame dimension info

http://chevy.oldcarmanualproject.com/shop/1955truck2/55ctsm0202.htm

One more thing, if you're going stock, all '55-'59 LCF trucks were equipped with V8 engines. The 2bbl smallblock would be the correct engine, the one from the AMT '55 or '57 pickups will fit the bill perfectly, but the trans will need to be changed.

Link to comment
Share on other sites

No problem. Old Chevy and GMC trucks, especially the '55-'59 models, are my favorite vehicles. I even have one, a '55 3200, as my daily driver.

One more site you may want to check out, Stovebolt.coms Gallery. http://www.stovebolt.com/gallery/gallery%2056%2059.html There's several LCF trucks in there, some restored, some not. Might help give you a good ideas on weathering your build, especially where those trucks tend to rust.

Link to comment
Share on other sites

The Titan should work fine, but the LCF was not available as a Tandem axle from the factory. There were aftermakret conversions for them, most using a "dead" rear axle, meaning that only the forward rear axle drove, and the rearward axle was basically there to support the weight. Not sure what suspension is under the Titan kit, but a Hendrixson walking beam, which is found under most AMT semi truck kits, would be most accurate.

Link to comment
Share on other sites

Im going for kinda of like the guy had a tree fall on his truck and had a 5700 caab behind his shed. So he just put this on to replace it. I was thinking of the bison or even a transstar 4300

Edited by blazefox
Link to comment
Share on other sites

No sense in worrying about how the factory did it with the cab you want to use.A ford chassis has huge beams,taller than a titan,but would give you the compact cat 3208.I think go with the titan,for the suspension,the best spoke wheels in kits,and the 8 cut down to a V6 should fit under the hood.

The titan comes with spare parts that you could get some interesting building choices,it's custom so any thing goes.

I'm with Richard about using a 2 ton opal for a chassis closer to stock .

Link to comment
Share on other sites

I'm with Richard about using a 2 ton opal for a chassis closer to stock .

The Opel Blitz chassis would be no where close to stock for that truck. About the only part that might work for a stock build would maybe be the rear axle and springs, the rest is incorrect for a US spec GM truck after 1946. Even for the earlier trucks, much would need to be changed to make it correct.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...