Jump to content
Board will be offline for a little while tonight ×
Model Cars Magazine Forum

1/16th 69 Camaro ProMod 7/22/14 motor painted


Romell R

Recommended Posts

Brad Is it talent or am i truly krazy lol!!!

Stan your wait is over thx for the compliment buddy and welcome to MCM forums

Fellas I have a small update today I was able to re-build the heads I figured since there was so much flack about my heads when i first started them that they really need to stand out so I gutted them and built em right. Now they will have rockers, rods and springs. And now I will be able to show the car with or with out the heads. I hope you enjoy.

heres the heads before i gutted them out. I built actual exhaust tubes running thru them........

20140522_155348_zps73e7uud0.jpg

gutted im only using the front and sides....

20140522_164114_zpszqjt6c7r.jpg

here the exhaust tubes are added.....

20140522_164123_zpsyakfe9km.jpg

heres one of the almost finished heads with a rocker i made i wont install the rockers and springs untill the heads are painted...

20140522_191006_zpsblx4snkc.jpg

heres the back .......

20140522_195433_zpsqcco8hv9.jpg

thx for joinin me see ya real soon....... B)

Link to comment
Share on other sites

Thanks fellas for your support ( which is much appreciated believe me) .

Brad my fingers are like the fingers of a KunFu master who has honed his skill for 40+ years (lol Ive been waiting to use that one) lol... no blisters here Bro (now burnt fingers that's a different story)

Chris: thanks for the link young bro, what size did you purchase?

Well in my never ending serch to inprove my tunnel ram i added the nitrous ports this is where the actual nitrous nozzles with hook up, one on each side of the plentums (inside and out) so I started by drilling holes all the way through then i inserted small diameter tube into the holes just till the tip comes out on the inside then soldered it in place. it was then cut off and ground to the correct size.I also added two throttle linkage supports. most of it is cleaned up now and ready for paint (w)hich will happen after i get the weld beads.

here you see the holds drilled thru the plentums.

20140601_095056_zpsenfid5yq.jpg

Here the smaller tubes have been soldered into place.....

20140601_095117_zpsnxtnfr4b.jpg

Here the tubes have been cut and shaved , I noticed the metal work have a gouge in it that needed to be filled so thats why you see the blob of solder on the side. (cant use bondo or putty on brass) it will be ground down and smoothed with jewlers files.

20140601_140759_zpsbszlgu2o.jpg

Here the gouge has been fixed and the two throttle support brackets can be seen.

20140601_141841_zpsuzwrlybz.jpg

just a little clean up needed,,,,,

20140601_231053_zpsc2zvfeae.jpg

Thanks for joinin me see ya soon..... B)

Link to comment
Share on other sites

Thanks Jarrod I just so happen to have one on me now.......A picture that is.

I cleaned up the tunnel ram then gave it a light coat of primer. I do this to show any imperfections then i go back and work on them I see a few here that ill address now.

20140602_120528_zps9fedbeel.jpg

Link to comment
Share on other sites

I just want to say what great talent you have and workmanship you have and skill to do all this work ! bravo my friend you are a great builder in the little toy world. I bet if you added oil & fuel it would run . thank you for showing how it all came together . I wish I had the time and talent ! clay

Link to comment
Share on other sites

Thx Glen i cant wait to see this one finished too.....

I modified my oil pan by adding the pump ports, I also notched it for the filter it not done but close.

20140606_193948_zpsst1yx5ty.jpg

Inside......

20140606_193914_zpsyx11gedn.jpg

20140606_194000_zpssvo8adni.jpg

started prepairing the carbs for detailing.....

20140606_194058_zps2gkhqqcz.jpg

And heres my proof that I can build a box stock kit lol...

20140606_194743_zpsrsaqcxrk.jpg

thx for joinin me .................. B)

Link to comment
Share on other sites

Hey fellas Ive known for a while that my right head was shorter than the left so i need to add to it. I soldered another end on and filled the gap with solder then shaped and smoothed it. now the valve covers fit just right.

here you can see the material added to the right side, i had already done some shaping.

20140608_113232_zpsakt06kpp.jpg

a lil more shaping and the top has been ground out.

20140609_215156_zps6leieokb.jpg

see the valve cover fits just right now. (man I cant wait to get some paint on these ugly parts)

20140609_215534_zpsxvo7h5ep.jpg

Thanks for joining me see ya again soon....... B)

Link to comment
Share on other sites

  • 1 month later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...