98 dodge one ton 4x4 dually

[redneckrodder]

its a 3/4 ton 4x4 used axles from revel 3/4 ton 77 chevy plow truck might add the plow mounts based on the monogram dreamrides svt color is krylon short cuts red pepper might have a 12 valve in it

-redneck

Edited August 30, 2014 by redneckrodder

[Platerpants]

good start

[redneckrodder]

thanks I wont be getting a whole lot of work done until I can build the 12 valve and order a new windshield I can build a flatbed gooseneck for it gunna just be an all around haulin truck

Edited September 17, 2013 by redneckrodder

[PappyD340]

NICE!!

[redneckrodder]

goin outside to build a new workbench then work on the dodge any info on how to build the 12 valve would be helpful thanks

-redneck

[Platerpants]

goin outside to build a new workbench then work on the dodge any info on how to build the 12 valve would be helpful thanks

-redneck

its highly requested but you dont see much if any of them being built.

[redneckrodder]

got some work done made a headliner out of red felt I had and pained the frame flatblack

[redneckrodder]

prepping to paint the bedliner will post pics in a bit

[pyrophoenix83]

any new picks of this truck i have the same truck but i wanna see how you did the 3/4 ton axles

[redneckrodder]

No i dont have any pics right now because it decided to be an extended cab and ive been to busy to go get another dodge kit and want to take my girlfreind somewhere nice soon but i will tell you how i did the axles it may not be exact but i used the axles from the revell 77gmc plow truck and lastnight i corrected the front axle because the diff should be on the drivers side and im lucky enough to have a 1:1 98 1500 in my backyard

[redneckrodder]

Any opinion on color schemes for a shortbox extended cab cummins ??

-redneck

[pyrophoenix83]

i would do dodge blue and i have the same kit but im trying just getting back into it. i would try and do stacks on it if you do a cummins in it

[redneckrodder]

Im thinkin about stacks or a tip

[cavemanx]

A shorty 3/4 ton? Never seen one. Do they even exist?

[Platerpants]

nope but people have done those kind of conversions

[Trailer Trash Kustomz]

I resin cast a1st gen 5.9 cummins diesel.

[redneckrodder]

I resin cast a1st gen 5.9 cummins diesel.

how much ?

[Trailer Trash Kustomz]

$22 shipped in lower 48

[redneckrodder]

22huh what all is included

[cavemanx]

Just the engine I think... Not worth it to me, but I'm not you.

[Trailer Trash Kustomz]

Heres a few pics and I have a twin turbointrcooler setup for it as well.

[redneckrodder]

how accurate would it be for a 98 you said its firstgen right how much is it without the transmission

[redneckrodder]

Would anyone happen to have the amt snaptite duallybed or anyone cast the rear dually fenders

[redneckrodder]

been awile so not much work has been goin on with the dodge because I haven't got another kit but I might just order the new body but I found dually bedsides in resin on ebay for 12 bucks considering makin an ebay account and buyin em

[RodneyBad]

I'd think you'd be better off finding a kit.

That Resin piece looks like a cheesie cheese cast.

Or POS for short..