Haubenschild Posted February 25, 2012 Posted February 25, 2012 (edited) I got this kit yesterday. This build will put all my modeling skills to the test ( been building for around 8 months ) , all comments are welcome I started off by filling the sink holes and cleaning up the main parts of the body Here is a mockup before primer Edited March 2, 2012 by Haubenschild
Haubenschild Posted February 25, 2012 Author Posted February 25, 2012 Here are the engine parts ready for primer
Haubenschild Posted February 26, 2012 Author Posted February 26, 2012 The main body and wing have been shot with Tamiya fine white primer
Rmodeler Posted February 26, 2012 Posted February 26, 2012 Alright! I'm in! Found this great ref pic on Wikipedia of most of the business end: http://en.wikipedia.org/wiki/File:McLaren_M23_DFV.jpg
Haubenschild Posted February 26, 2012 Author Posted February 26, 2012 Thanks for the reference photo roger! , I will definatley use it!
Scale-Master Posted February 26, 2012 Posted February 26, 2012 I know it's a little late, but I have found it is easier to build the engines on these kits before priming/painting. At the rate you are going I would expect to see you doing another car that uses the same engine though...
Haubenschild Posted February 27, 2012 Author Posted February 27, 2012 I will make sure to do that next time Mark. The engine block has been assembled and shot with one coat of Tamiya TS-17 aluminum , after another coat of aluminum it will be dull coated
Mike Kucaba Posted February 27, 2012 Posted February 27, 2012 Interesting. I have this kit and popped for the PE set also.Formula 1 is somewhat foreign to me so I'll keep up on this.
Scale-Master Posted February 27, 2012 Posted February 27, 2012 Actually... I think it looks good with the shadows in that shot enough to maybe just go to the dullcote. But then it is just one picture, I'd hate to steer you wrong from one photo...
Haubenschild Posted February 27, 2012 Author Posted February 27, 2012 (edited) The interior was masked off and brush painted with Tamiya XF-16 flat aluminum. I probably should of shot the interior with gloss aluminum since the interior is quite shiny in pictures of the actual car and the fact that the finish is quite textured because of my subpar brush painting skills Edited February 27, 2012 by Haubenschild
Haubenschild Posted February 27, 2012 Author Posted February 27, 2012 (edited) The chassis has been masked off and sprayed with Tamiya aluminum paint The engine has been wierd , This is the first time I have wired an engine , the silver details were picked out with a sharpie ( I will clean up the silver mistakes with black sharpie ) Edited February 27, 2012 by Haubenschild
Haubenschild Posted February 28, 2012 Author Posted February 28, 2012 The wing and top half of the body have covered with 3 coats of Tamiya TS-26 pure white , after masking off the white , Tamiya TS-36 flourescent red will be applied. I know that TS-36 isnt the exact colour , but I dont want to wait 2 weeks for paint
SuperStockAndy Posted February 28, 2012 Posted February 28, 2012 Very cool Never knew they ran Ford engines.
Haubenschild Posted February 28, 2012 Author Posted February 28, 2012 Here are the same parts with 3 coats of Tamiya TS-36 flourescent red
Haubenschild Posted February 29, 2012 Author Posted February 29, 2012 (edited) The tape has been removed , It didnt come out as crisp as I wanted.. Doo you guys have any tips on masking? , I would really appreciate it , thanks. Edited February 29, 2012 by Haubenschild
Rmodeler Posted February 29, 2012 Posted February 29, 2012 (edited) The yellow Tamiya masking tape cuts a pretty fine line. Also there's this stuff I sometimes use called Parafilm. It's reeealy stretchy and will conform to just about any shape you put under it. http://www.micromark...ilm-m,7551.html Not cheap anymore i notice...lol Heres an idea that may or may not work. What if you waited until the paint is really dry, lightly sand down the rough edge, then take a thin strip of clear decal film which you've painted with the same fluorescent red and lay it over the edge, it might do the trick. Since the color breaks are all straight on that McLaren, it might work. I don't know if the paint will melt the decal film, gotta test that, but just thinking out loud ... lalalalala Oh PS: If you can rig up an X-acto knife with two parallel blades, you can cut nice even-width strips from the decal film. You just have to figure out how wide you want them to be before you make the knife. Edited February 29, 2012 by Rmodeler
Haubenschild Posted February 29, 2012 Author Posted February 29, 2012 Cool tip roger! , I will be sure to try it out!
Mike Kucaba Posted February 29, 2012 Posted February 29, 2012 Just curious,but what would be the actual red color for this. And I don't use this tip often,but the really best stuff for getting a tight line between colors is Bare metal foil. And I use to work for 3M and their best tape doesn't works well,but is cheaper.
Haubenschild Posted February 29, 2012 Author Posted February 29, 2012 (edited) I am not sure what the exact colour is , but I have heard that Hiroboy makes a red that is very similar to the red on the 1:1 Edited February 29, 2012 by Haubenschild
Roadkill2525 Posted February 29, 2012 Posted February 29, 2012 Liam, the flourescent red would be correct for the McLaren MP4 cars and the Penske Indy cars
Rmodeler Posted February 29, 2012 Posted February 29, 2012 (edited) The "rocket red" has changed over the years it was active. I know that the red and white paint for the Penske PC-18 was manufactured by PPG. But the red of the era McLaren you are building was far more orange looking in person. By contrast, the fluorescent red of a 1990s Senna McLaren was far redder and more similar to the Penske color. Edited February 29, 2012 by Rmodeler
Haubenschild Posted March 1, 2012 Author Posted March 1, 2012 (edited) I added the decals to the top of the body ( I will be using the decals for James hunts' car ) and yes I will fix the crooked # 11 decal Edited March 1, 2012 by Haubenschild
Haubenschild Posted March 2, 2012 Author Posted March 2, 2012 I assembled the transmission and added decals to the engine
Haubenschild Posted March 4, 2012 Author Posted March 4, 2012 Today I added a few more things to the engine , I will have to wait at least a week to get paint for the Headers though , which is kind of annoying
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now