semijoe Posted September 25, 2013 Posted September 25, 2013 (edited) finally able to get started on this build, ive been wanting to do this for along time. I believe ive done enough research and download enough pictures to get start like all my builds it wil be r/c with a working arm . ive scale this out to be a 1/10 which is really big, somt times I think I take in to much fumes . lol ive measured this out to be around 790mm, tires are 126mm using 2.2 rims theres going to be a lot of 3 steps forward and many steps back . im going in 1/2 blind on this and don't know what walls I will be hitting. im assuming around 400 hours , so this will be great winter coming build . well enjoy the movie and lets get started ive cut the frame rail, I some what know where the axles go, I need to make the lower hull 1st. ive started by intergrading the rails in the hull, starting from the front Edited September 27, 2013 by semijoe
semijoe Posted September 26, 2013 Author Posted September 26, 2013 so far everything is located at the right height and right place , I do have to make some new frame rails as these are alittle short . but in the mean time I will work with these to see rear everything else goes . running from the front leaf to th axle is a stabilizer , I have to make these and the mounts
Mike Kucaba Posted September 26, 2013 Posted September 26, 2013 WOW!!! and I've been whining about building in 1/16th!!!
semijoe Posted September 26, 2013 Author Posted September 26, 2013 stabilizers and front hangers are done
semijoe Posted September 28, 2013 Author Posted September 28, 2013 transmission is in place and front drive is installed , working my way back , the transmission is a rc4wd r2 single speed with a 55 turn motor, I cut new frame rails at the correct length this time at 29.5 inches
semijoe Posted September 29, 2013 Author Posted September 29, 2013 had a chance to work on this alittle today ive added a crossmember in front of the transmission, added 55 turn motor and start with the slats on the side of the rails
semijoe Posted September 30, 2013 Author Posted September 30, 2013 next I made a transmission cover , heres the basic piece. next I have to sand and detail alittle , and drill some mounting holes
semijoe Posted October 1, 2013 Author Posted October 1, 2013 I usde a high torque servo and mounting it to the frame ,then I made a steering box
semijoe Posted October 1, 2013 Author Posted October 1, 2013 lower fender post are mounted and I found some 5 inch foams, heres alittle tease
semijoe Posted October 2, 2013 Author Posted October 2, 2013 today I made opposite side steering box , added about 100 micro screws everywhere and started on the sides push bars
semijoe Posted October 3, 2013 Author Posted October 3, 2013 wahoo! tires and rims are in ive started on the walker beam suspension, there is a lot of parts in volved , but heres the basics
semijoe Posted October 4, 2013 Author Posted October 4, 2013 time to work on the rear suspension, 1st I drilled and tapped some holes in the yota axles, ive added a ball end next ive add the ball ends to the belly and added 2x links, this will keep the axle leveled next Ive added a cross stabilizer drive shafts installed and a glimpse at it with tires on it
semijoe Posted October 7, 2013 Author Posted October 7, 2013 Incredible craftsmanship! Joe, you do amazing work!! Just awesome!! thanks guys !
semijoe Posted October 7, 2013 Author Posted October 7, 2013 today I started on the side nerf bars/protection rails
semijoe Posted October 7, 2013 Author Posted October 7, 2013 cross members are glued and screwed, top rails are done, next I need 6 more fender post and then the chassis is ready for primer
semijoe Posted October 8, 2013 Author Posted October 8, 2013 the lower chassis is done , all running gear works good , everything is made to come apart and now its primed
semijoe Posted October 9, 2013 Author Posted October 9, 2013 ive started on the upper hull, I wanted to do in a one piece, but again some where down the line I would need to take apart, but the cap/roof will be one piece . in side the hull I made 1/8 metal ribs, will cover with .040 plastic for interior
semijoe Posted October 10, 2013 Author Posted October 10, 2013 I made a tire rack, the out is plastic but the inner parts are metal. it will hold with no problem
semijoe Posted October 11, 2013 Author Posted October 11, 2013 made the exhaust, was hoping to use the Tamiya big rig, but wrong, this is 2x the size, the main exhaust is 1 inch pipe . crazy big man . next is the windows
semijoe Posted October 14, 2013 Author Posted October 14, 2013 started on the rear door made the inner door made the outer door working hinges and door latch is made
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now