Custom Hearse Posted October 29, 2009 Posted October 29, 2009 What is the best way to store 2 part putty so that it lasts longer? Every time I buy it, it seems to get hard inside the container. Should I store it somewhere cool, warm, or room temperature, so that it doesn't dry up as fast? Thanks!
Zoom Zoom Posted October 29, 2009 Posted October 29, 2009 2 part putty is a lot like bottles of superglue. They always dry out before you will use them. Body shops go through the putty quickly. It takes us years to go through a container. You might have success at putting it into smaller, sealed containers. Or not? I've thrown away countless bottles of superglue and probably a half dozen less-than-half-used containers of putty that dried up. The upside? You can now get a smallish tube of 2-part Bondo glazing putty at Pep Boys (looks like the same type/size as the tube of air dry stuff, but has catalyst, it's in a similar hang-tag type of package), about 7 or 8 bucks, much more likely to be able to use it up before it goes bad than a larger container.
Custom Hearse Posted October 29, 2009 Author Posted October 29, 2009 Thanks Bob! Unfortunately there isn't a Pep Boys around. I did buy a small container of Bondo brand 2 part putty yesterday. Maybe if I put it in the fridge like I do super glue, it'll last longer. I don't know where I would find containers for it...
modeltrucker Posted October 29, 2009 Posted October 29, 2009 You can try putting plastic wrap over the unused portion left in the can to keep it fresh. james in cleveland
Harry P. Posted October 29, 2009 Posted October 29, 2009 The smaller tube of Bondo is a good idea. Also, if you're talking about the traditional can of Bondo, try storing the can inside a slightly larger, airtight container... like a piece of Tupperware or similar. And make sure the lid on the can itself is tightly closed.
Custom Hearse Posted October 29, 2009 Author Posted October 29, 2009 More great ideas! Thanks guys! Here's the putty I bought from Auto Zone... Thanks again guys!
FujimiLover Posted October 29, 2009 Posted October 29, 2009 I never finished any projects I started with bondo. I think it's a waist for what we're doing. Good luck with it! I'd stick with MilliPut.
Custom Hearse Posted October 29, 2009 Author Posted October 29, 2009 I've never used the putty seen above before, I usually use Evercoat 2 part putty, But I thought I would try the Bondo brand this time. Never had a problem with it ever.
E St. Kruiser50 Posted October 29, 2009 Posted October 29, 2009 I've never used the putty seen above before, I usually use Evercoat 2 part putty, But I thought I would try the Bondo brand this time. Never had a problem with it ever. I've used EVERCOAT RAGE for ten years or more. Tried Bondo once, but it finished so badly I threw it away. Here's what I use to "REFRESH" my Evercoat fillers. It's nothing but pure resin in a quart can. Anywhere resin can be purchased, like at a craft or plastics store, you can find some. Doesn't have to be this brand, as long as it's resin. It may be called "Casting Resin".
Custom Hearse Posted October 29, 2009 Author Posted October 29, 2009 Thanks Dave! I never knew that existed. I'll have to find some... Then I'll have to bug you about how to mix it! Thanks again Dave!
E St. Kruiser50 Posted October 29, 2009 Posted October 29, 2009 Thanks Dave! I never knew that existed. I'll have to find some... Then I'll have to bug you about how to mix it! Thanks again Dave! NO PROBLEM MARSHALL - IT'S EASY TA MIX Ya just keep adding the "REFRESHER" to your filler until it's about the consistancy you want, take a bit out of the container, add a bit of catalyst, mix, and your ready to spread. Most brands "Set-up" faster than others, so I'd do several very small batches to see how much hardener to add, and how fast it sets up. Been usin' mine so long that it's like "Ridin' a bike" , ya "just do it" .
randx0 Posted October 29, 2009 Posted October 29, 2009 (edited) Marshall can you give a report on how that bondo works for you I generally stay away from bondo but lately I can't find evercote anywhere. I've used EVERCOAT RAGE for ten years or more. Tried Bondo once, but it finished so badly I threw it away. Here's what I use to "REFRESH" my Evercoat fillers. It's nothing but pure resin in a quart can. Anywhere resin can be purchased, like at a craft or plastics store, you can find some. Doesn't have to be this brand, as long as it's resin. It may be called "Casting Resin". Gee Whiz Dave everytime I think you have run out of tips BLAM you lay down the most useful info ever. I never even thought about using resin for thinning out body filler .one of my biggest problems with that two part stuff is it comes out a little too thick for me to do what I'm accustomed to. Edited October 29, 2009 by randx0
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now