Let's see where this goes......Porsche Trike........

[ajwheels]

The 6 cylinder heads............

And here they are fitted to the cylinder barrels........

[ajwheels]

Cam housings and covers...........

Installed on motor, top view.............

Bottom view, with oil-return tubes..............

[ajwheels]

The oil cooler loose.......

And then installed..........

[ajwheels]

The cam chain housings and covers...............

[ajwheels]

Cooling fan and fan housing........

Fan and housing set upon the motor.................

This is all temporary, as these parts will be installed after the engine goes into the frame.............at least that's the plan................

[ajwheels]

Here are a few images with the fan shroud, fan pulley and engine case vent cover thing.................

[cobraman]

Lookin' great !

[ajwheels]

Trial fit of the distributor, intake manifolds and throttle bodies............

Further detail pieces will probably wait until I get closer to putting this into the frame.................

[ajwheels]

Just about time to bring the pieces together and figure out the remaining details.............

[monkeyclaw]

I don't see any mention of scale....what scale are you working in? And could I get the same engine printed in 1/12 scale??? I would really like to use the non turbo engine for a monte carlo rallye car in 1/12 scale...............feel free to PM me with any details..............matt

[ajwheels]

Matt.......the scale here is 1/16...........a bit small for some of this detail, but workable if patient...........

PM sent..........

Tony

[ajwheels]

Now this is the fun part for me...........here are images of most of the rear end put together............

[Custom Hearse]

This is truly awesome! The details are sharp, and the look is wicked cool! I will definitely be checking in on this build!!!!!!

[ajwheels]

Here are the rear brake pieces installed....................even the brake pads..............

[Pro Wrench]

I wish I knew more about 3D printing. The amount of detail in this is unbelievable. This is a very cool build.

[ajwheels]

Thanks for the comments............Derick, hope that hand gets better, that hurts me just thinking about it...................and Curt, there is a lot of info out there about 3D printing........it's getting more accessible every day.........it does open up a whole lot of possibilities.................pretty much endless possibilities, really...............

Tony

[ajwheels]

Here are a few images of the engine in the frame..............

[ajwheels]

The Porsche motor, having a dry-sump oiling system, will need an oil tank.................this one will fit nicely under the seat area..................

[Foxer]

This looks amazing with the engine in place! Just a Porsche engine with a seat!

That yellow color just looks right!

[ajwheels]

A few images with the fan, fan housing and shroud re-installed on the engine...............

[Austin T]

What kind of tank are you gonna put on there?

[ajwheels]

Austin...........the tank will be a fat, early-style Harley Davidson type...........twin filler caps with an instrument pod on top.............at least that is the plan so far.............there is an image that shows it back on post 36 of this thread.....................

[Ira]

BEAUTIFUL WORK TONY!!!

[GrandpaMcGurk]

Thanks for the comments............Derick, hope that hand gets better, that hurts me just thinking about it...................and Curt, there is a lot of info out there about 3D printing........it's getting more accessible every day.........it does open up a whole lot of possibilities.................pretty much endless possibilities, really...............

Tony

3-D printing is not only more accessible but the technology just keeps getting better & better.....it's hard to believe that Tony's trike is only 1/16th scale!

[ajwheels]

Thanks, Ira, I appreciate the good word.............

And Don's comment about this being 1/16 scale, well, it's a bit small for my drifting eye-sight and fat fingers, however, I took a shot at flaring some aluminum tubing for the ram tubes on the throttle bodies............then installed the intakes on the engine.........