CrazyCrank

Thanks for this huge praise, Bugatti Fan 😎

Thanks a lot for your kind words, Big Messer And to reward you:

Thanks a lot, Absmiami, for your wishes, and for liking my work

Hello everybody I've put in place the fuel filler cap Of course, all the parts I assembled for this fuel filler trap aren't supplied in the kit ! I 3D designed and printed them ! Work on the grille grilles: Indeed, I intended to improve a bit the two parts Revell supplied for the chromed grill... Those parts are very disappointing because the spaces between the chrome blades of the grill are not empty ! So, I begun to sand them from the back, carefully, until I almost reached the braces, by rubbing them on a 180-grain file. Then, I finished the job with the point of a scalpel blade, little by little. At least, I sanded carefully the blades using a thin strip of 400-grit sandpaper. WIP: And hereunder is the final result after 4 stressing hours : These modified parts took a bleach bath, and were supposed to be painted chrome later. BUT, as my mind is trained to track every defect, I (un)fortunately noticed that the kit parts for the grilles are inaccurate ! 😮 In fact the amount or horizontal blades on the kit parts is 4, while on the actual car, it's 6 ! 😡 So, it remained no other option than manufacturing new grilles ! I designed them in Fusion 360 I 3D printed in resin this design and got a nice result: The parts were painted chrome using GreenStuffWorld airbrush chrome, over a gloss black base (from ALCLAD) and I got excellent results : That's all for now ! Stay tuned for next episode

I'm very happy you received these rewards....your models and you definitely deserve it ! Congratulations 😎

I understand your great interest for this gorgeous model. I 'm a French modeler, and I recently crossed the pond, almost only to touch this model with my eyes in Canada ! It was worth the travel ! and François is also very welcoming ! CC

Thank you Mattilacken for this great comment. Yes it's tricky, but within everyone's reach with a little determination and patience

Thank you so much for this praise, Pico 😎

Hello everybody Sorry for not posting anything for almost a year; I've had serious health problems again in the meantime, and have very little time available. So I'm picking up where I left off, and the next few posts will take you through to the completion of the assembly. Improvement of the steering wheel: The kit part has good shapes, but all is too thick, so, I began thinning the part, using a scalpel. On the picture below, you could see the beginning of this job: on the right only, thinning has begun. Unfortunately, I forgot to take pictures of the achieved job. After priming and painting: You could notice on this last picture that I've added some grooves between the 2 "horizontal" struts on the left and on the right side as well. I took inspiration of this photo: Purists will notice that there is 13 grooves each side on the real steering wheel and that I added only 9 ! Why ????....Because I can't count past 10 😂..... more seriously : because I made this mistake ! shame on me ! Clear coating: I had in my stash some spare metal transfers from my Tamiya Mercedes Benz 300SL, and, particularly, a chromed ring, a bit too wide, but would do the job to represent the ring on the BMW 507's wheel centre. I've still to paint semi-gloss black the vertical struts of the steering wheel situated between its horizontal ones, and add at each end of them a fine chromed strip (Hasegawa mirror finish), taking inspiration of the previous picture of the actual. car. The steering column : - I've cut off the indicator control lever, on its right, much too thick ! - And replaced it by a scratched one, using 0.3 mm piano wire and at its end, a droplet of UV curing resin, plus a tiny washer (PE part from Tamiya MB 300 SL detailing kit) - A little touch of ivory paint at the end of the indicator lever, for covering the resin and... that's it ! The ref. photo is the same My interpretation: Assembly and some additional details: And, having received my rivets, I placed six 0.5 mm flat head rivets on the top of the dash: I just placed the wheel near the dash to take the picture : The handbrake handle has been chromed and is now in place: I've added the superior knobs which heads are painted te same color than the bodywork. I cheated and used Hiroboy 1:24 toggle switches. They are metal made. I drilled two 0.4 mm holes at the right places on the dash and inserted the switches into them. Then, a little drop of white on the heads, and ....that's it. Maybe they are a little bit oversized if you look at them from profile view, but at the naked eye, it looks pretty nice. Making of a BMW key ring: It's amazing how little things can take so long to get done 😮 I 3D drawn and printed this: A pretty disk with an eyelet , and on the disk, 4 sections of the same size, 4 "pie slices", that are slightly dug in the disk, and in which I could "pour" some blue and white paint, without overflowing too much. 3D drawings: The 3D printed parts The key ring painted silver plus the slices, 2 blue, 2 white 1 And then, several layers of Gauzy agent, to create a nice shine and give thickness. On this picture, the Gauzy agent hasn't yet dried and look a bit "milky". Once fully dried, it will be totally transparent (Initially, I used transparent nail UV resin to give the best shine and relief, a bit like a curved glass. It worked perfectly but the slightest manipulation of the UV cured part led to dulling the resin, so...) I've also printed some ignition keys. It remained to do the more delicate job: linking ignition key and key holder with a very thin metal wire to simulate the chain, without breaking the eyelets of the key holder nor/or the ignition key (My first key ring made with UV resin has been broken during this process) The keyring is now attached to the ignition key 😎 It took a long time because I had to start over several times. Either I broke the eyelet on the key, or the eyelet on the keyring, during the delicate operation of creating a chain between the two with 0.15 mm wire. As a result, each time I had to either repaint a key, or - and this took longer - repaint and varnish a keyring! The total length is about 7 mm: 2.2 mm for the keyring, 3.5 fr the ignition key and the rain for the chain My eyes won't be able to work on this 1:24 scale for much longer ! And it took its place on the dash: That's all for now, guys. Thanks in advance for your comments and criticism 😎

Once again, François, you've produced something absolutely "marvellous" ! CrazyCrank, from MTRL

Dropped my jaws on the floor, again ! 👍

Hello everybody Today, I'll show you how I made and assembled all the dashboard components - part 1 - The dash was semi-gloss clear coated - The decals have been placed, not without difficulty because those ones were very fragil. Used a lot of Microscale Microsol to soften them, but damaged a little bit the central one (not visible at the naked eye) - Once dried, I sprayed a finale layer of 1K Gravity clear over the decals .... et voilà ! Next I 3-D drawn and printed a new handle for the handbrake (the lever I thought it was a starter, placed under the dash on the left side) It will be painted with Molotov Chrome I 3-D drawn and printed the different knobs of the dash and radio They will be painted ivory. I 3-D drawn and printed a new passenger handle (placed on the right side of the dash, on the right of the glove box). It will be painted matt black The meter's glasses have been improved using drops of Gauzy agent put on the decals. Once dried, it's fully transparent and shiny I've scratched the gauge's bezels, the elements of the fake glove box hinge, and the chrome frame of the speaker and radio with Nickel-Chrome 0.25 mm wire I've already glued the bezels of the 3 meters and fabricated the fake hinge for the glove box. All those little bits of Nickel-Chrome 0.25 mm rod have been glued using Gauzy agent (from AK), instead of Micro Liquid Tape, because it's much less thick, dries faster and if much more transparent. The thin mesh of the radio speaker, at the top center of the dash, was simulated inserting in the hole a rectangular piece of thin mesh (0.1 mm It has not the right number of rows (30 would be needed to be accurate) but looks good imho. The grill is in place, and the meters's bezels as well: Then, I painted chrome all the dash knobs that I'd resin printed. And next, I brush painted ivory the buttons, under magnifying glasses I had also painted chrome he passenger handle, because on its top end, there is as well a chrome bezel, and I've painted the handle Nato Black (AK 11360), which looks like a black leather. The result is really nice : The dash knobs an radio buttons were placed on the dash. To highlight them, they have been painted light ivory instead of Pearl white, as the body. We can see, on the closest photo, their chromed bezels The handbrake handle was painted chrome and put in place: Stay tuned if you like, and thanks for watching and criticising. ?

I do love your highly detailed engine bay ?

Hi guys The dashboard I showed you painted with the new wheels isn't the kit part. In fact the kit represent a BMW 507 Series I when Elvis's one was a Series II, which has a different dashboard, amongst many other features. So, I hadn't any other option than make a new one...and what's more appropriate to do this job than 3D design and printing ? Hereunder the kit dashboard, and a picture of a series II dash: My drawing in Autodesk Fusion 360 All that stuff has been sliced, 3 pieces in 103% and 3 in 104% ( @Spiny ? ) And the 3D printed final part: I presented it on the windscreen, because it's no impossible to follow the assembly instructions which ask to fix the dash on the cabin. The new part will be attached to the windscreen frame:

In fact, as it is in the first post of this thread, she's not finished ? Indeed, I've added the little detail that makes THE difference: You should know that when The King finished his military service in Germany, he brought his car back with him to America. He was already famous and his female admirers regularly left lipstick marks on the pearl-white bodywork of his BMW as they kissed it fanatically. So much so that, fed up, he had it repainted red! ! A model-maker friend of mine was able to produce 1:24 scale decals on his dedicated printer, based on a ‘lipstick kiss’ design I provided him with, and, because I thought it"s funny, I've affixed several of these decals to the bodywork and windscreen here and there, as a nod to the history of The King and this incredible car. Let' see below some pics: Enjoy