Kit Basher Posted April 23, 2015 Share Posted April 23, 2015 I'm working on a 2009 Challenger, and could use some help with the window trim. I'm not talking about the black on the clear parts (windshield, etc.). My problem is the black plastic/ rubber that goes around the window openings on the body. I would like to spray it if possible. I'm thinking about spraying the black, masking it with BMF, and them spraying the body color. Or would it be better to paint the body, mask that, and then spray the black? Or are there other alternatives? There are a lot of areas on this car where black meets body color: all four window openings, grille, taillight area, rocker panels, air dam, and some areas under the hood. Suggestions please! Thanks much. Quote Link to comment Share on other sites More sharing options...
gbdolfans Posted April 23, 2015 Share Posted April 23, 2015 Hi Hugh,I have great success using a black Sharpie.They come in different sizes with different types of tips.Laying it on it's side is great for window trim,engine details,etc... Hope this helps,George Quote Link to comment Share on other sites More sharing options...
Austin T Posted April 23, 2015 Share Posted April 23, 2015 Personally I would use the sharpie,but if you do want to go with paint or the area is too big for a sharpie I suggest you use BMF for the edge of the area you want to paint and then make sure to mask of the rest of the surrounding area with tamiya tape or a similar substitute. Make sure of course to do this after the body color has dried. Quote Link to comment Share on other sites More sharing options...
MonoPed Posted April 24, 2015 Share Posted April 24, 2015 I sprayed the trim on my '15 Mustang. After the clear was cured up a bit, I masked with Tamiya tape, and and sprayed Tamiya acrylic through the airbrush. I did the '06 Mustang the same way. Quote Link to comment Share on other sites More sharing options...
Kit Basher Posted April 24, 2015 Author Share Posted April 24, 2015 That looks great Brian, that's exactly what I want. How did you do the masking? Did you put tape on and then cut around the openings? What Tamiya paint did you use, flat or semi-gloss? Thanks Quote Link to comment Share on other sites More sharing options...
935k3 Posted April 24, 2015 Share Posted April 24, 2015 It is allot of work but masking and airbrushing give the best results. Quote Link to comment Share on other sites More sharing options...
jwrass Posted April 24, 2015 Share Posted April 24, 2015 Nice work Brian!!!! Time well spent equals great results!!! Jimmy "RASS" Quote Link to comment Share on other sites More sharing options...
Kit Basher Posted April 24, 2015 Author Share Posted April 24, 2015 Has anyone tried doing the black first, then masking and shooting the body color? Quote Link to comment Share on other sites More sharing options...
MonoPed Posted April 24, 2015 Share Posted April 24, 2015 If I can run the tape along the edge of the trim without cutting it, I will, but if I can't, I apply the tape, and carefully trim with a fresh blade. I used semi-gloss black, but with the low psi and just barely pulling the trigger black to avoid runs and bleeding under the tape, it came out a lot more flat than semi-gloss. Quote Link to comment Share on other sites More sharing options...
Kit Basher Posted April 25, 2015 Author Share Posted April 25, 2015 Thanks, Brian! Quote Link to comment Share on other sites More sharing options...
Jonj238 Posted April 30, 2015 Share Posted April 30, 2015 I found some paint pens made by a company called Forney, at my local auto parts store. They have an end like a sharpie marker, but it uses paint and not ink. They come in a lot of different colors and work great. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.