gks1964 Posted March 24, 2020 Author Posted March 24, 2020 I thought that was what it was. . I do have a PL Charger and was looking at that piece earlier, I needed someone such as you to clarify! Before making a mistake. Thanks Tim. Gerald
gks1964 Posted March 26, 2020 Author Posted March 26, 2020 Was able to make a casting of the items that I scratch built! Turned out pretty good, pic is bad sorry?. Gerald
gks1964 Posted March 28, 2020 Author Posted March 28, 2020 (edited) If anyone is interest in a resin casting of the bath tub intake I built ? I have less than 10 left. Send me a PM. Before they hit ebay! Gerald Edited March 28, 2020 by gks1964 ADD PHOTO
gks1964 Posted March 31, 2020 Author Posted March 31, 2020 I couldn't take the look of the first oil pan I built, so I remade! Think this looks much better.
DonW Posted March 31, 2020 Posted March 31, 2020 I found this. Wonder what happened next. Your build of it is great!
gks1964 Posted March 31, 2020 Author Posted March 31, 2020 5 minutes ago, DonW said: I found this. Wonder what happened next. Your build of it is great! BET it wasn't too good!!!!!!
yellowsportwagon Posted March 31, 2020 Posted March 31, 2020 2 hours ago, gks1964 said: I couldn't take the look of the first oil pan I built, so I remade! Think this looks much better. That looks really good man
gks1964 Posted April 3, 2020 Author Posted April 3, 2020 (edited) Actually got something accomplished today in between casting parts. I fitted the oil pan 2.0 to the block and front cover to make sure all fits The bottom of the block needed flattened out for the surfaces to mate properly. Also removed the oil pump and oil filter, will be replaced by new parts. Edited April 3, 2020 by gks1964 addition
gks1964 Posted April 7, 2020 Author Posted April 7, 2020 Anyone know of a source of small throttle return springs? I used to have some but I can't find them. Gerald
Force Posted April 8, 2020 Posted April 8, 2020 (edited) I usually make them myself, take a very thin wire and coil it tightly around a piece of a thicker wire, stretch it out a bit and make a loop at a right angle at both ends and you are done, takes about 5 minutes to do. Here is one I did. Edited April 8, 2020 by Force
gks1964 Posted April 12, 2020 Author Posted April 12, 2020 Got a little done. Added the engine mounts, air box frame to the firewall, made the cover fir the shifter platform. Also added the seat frame, rear firewall and fire bottle brackets. I've been try to build some upper control arms, with mixed results! Gerald
gks1964 Posted April 13, 2020 Author Posted April 13, 2020 One last test fit of the engine! Tim's advice about checking the fan clearance of the front frame member is real tight. Take his advice and check, recheck and double check! He also advised to leave the front engine cage bar off until the engine is installed, that is spot on. Thanks Tim great advice. Gerald
gks1964 Posted April 16, 2020 Author Posted April 16, 2020 (edited) Need help with radiator colors, most of the pix that I have of them are B&W? Is the core of it copper or aluminum? Gerald Edited April 16, 2020 by gks1964
gks1964 Posted April 29, 2020 Author Posted April 29, 2020 Got most of the engine wired and plumbed. One last test fit before the chassis gets painted.
gks1964 Posted April 30, 2020 Author Posted April 30, 2020 9 hours ago, yellowsportwagon said: Dude that looks killer man Thanks Tim! I think looks good. I may build another carb and cast it for the future. If anyone is interested here's a drawing of the 426 firing order.
Force Posted April 30, 2020 Posted April 30, 2020 (edited) It looks like your carburetor is based on the Revell/Monogram carburetor from the Pro Stock kits and I must say that I don't like them that much. I have been around Holley Dominators plenty and they doesn't really look like the Revell/Monogram carbs wich I think are quite crude, there are much better ones around. But...this one will be under an air box so it might not be that visible. Edited May 1, 2020 by Force
gks1964 Posted May 1, 2020 Author Posted May 1, 2020 2 minutes ago, dawgvet said: Really enjoying this WIP! Your engine looks great! Thanks!
gks1964 Posted May 1, 2020 Author Posted May 1, 2020 5 hours ago, Force said: Me to. I like your attention to details. Thanks!
gks1964 Posted May 8, 2020 Author Posted May 8, 2020 Anybody know if this car used seat belt reel behind the seat? If so any pix anywhere?
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now