adabiri2 Posted January 9, 2013 Share Posted January 9, 2013 Just wanna get some suggestions. Never tried it before clear coat, got a sheet of contengency stickers comin from SLIXX decals. Heard they were goin out of business, shame!! Quote Link to comment Share on other sites More sharing options...
Swamp Dog Posted January 9, 2013 Share Posted January 9, 2013 sometimes i clear coated over my decals and sometimes i don't..but i always put them on with micro set.. Quote Link to comment Share on other sites More sharing options...
cobraman Posted January 9, 2013 Share Posted January 9, 2013 I clear after. Slixx has decided to stay in business I believe. Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted January 9, 2013 Share Posted January 9, 2013 I would do both. decals work better on a gloss surface and clear on top after the decal seals it in As do I. The clear coat before gives you the ability to polish to a smooth surface to avoid silvering. The clear coat after protects the decals. I have decals degrade on older models where I didn't clear over, in particular, white colors yellowing. I would clear coat even contigency stickers as it would not be that noticeable if you apply a thin layer. And many modern race cars have wraps. Quote Link to comment Share on other sites More sharing options...
High octane Posted January 9, 2013 Share Posted January 9, 2013 I use clear coats BEFORE applying my decals as there's no need to protect them from rain, snow, sleet, hail, or ice as I keep my built models in a display case in the house. Modern race cars use wraps, but I build 60's race cars and wraps were not available then. Quote Link to comment Share on other sites More sharing options...
Harry P. Posted January 9, 2013 Share Posted January 9, 2013 This is a QUESTION, not a tip or tutorial. It should have posted in the QUESTION AND ANSWER section. Is this really that hard to understand? Quote Link to comment Share on other sites More sharing options...
Tom Geiger Posted January 9, 2013 Share Posted January 9, 2013 I usually don't clear at all. For most of my building I usually have weathered surfaces or at least used vehicles where clear coat would be an unrealistic shine. One thought on clear coats, regarding both decals and Bare Metal Foil, is that the clear coat gives everything the same tone. In real life, the paint, the chrome (even the difference between chrome and aluminum / pot metal trim) are different. Many decals on cars actually are stickers that sit on top of the paint and have more of a matte finish on them. I remember one time seeing a Nascar car that had everything buried under mile deep clear that looked totally unrealistic. So I would be doing my decals and BMF after my clear coat. Quote Link to comment Share on other sites More sharing options...
MsDano85gt Posted January 10, 2013 Share Posted January 10, 2013 It can go both ways I put decals on my finished paint, on some kits (molded in color kits)I place all my decals then shoot some clear over everything makes the plastic shine and protects the decals Quote Link to comment Share on other sites More sharing options...
Mike_G Posted January 12, 2013 Share Posted January 12, 2013 If your color coat is smooth there's no need to clear before decaling Quote Link to comment Share on other sites More sharing options...
Longbox55 Posted January 13, 2013 Share Posted January 13, 2013 I remember one time seeing a Nascar car that had everything buried under mile deep clear that looked totally unrealistic. That could depend on what era and whose car is being replicate, and what specific race it was intended to run at. Before the wraps became popular, it was not uncommon for teams to clearcoat over the sponsor and contingancy decals at the superspeedays (mainly Daytona and Talledega). This was to seal down the edges of the decals to allow for smoother airflow, and to prevent them from getting pulled up during the race. One team I know did this was RCR. I will agree, though, that a mile deep clearcoat would definitly be unrealistic on a racecar. On another note, if you're building any of the recent Round 2 releases, the decals have a flat finish, so if you want shiny, you just about have to clear over them. Quote Link to comment Share on other sites More sharing options...
CadillacPat Posted January 13, 2013 Share Posted January 13, 2013 If you lay your paint down smooth and correctly your Decals will apply and adhere correctly without any silvering. If you Clear before you lay down Decals they will appear to float above the surface of the paint. CadillacPat Quote Link to comment Share on other sites More sharing options...
Mooneyzs Posted January 13, 2013 Share Posted January 13, 2013 Count me in with the ones who clear over their decals. I have never had any trouble with my clear affecting the decals. Then again I am using automotive urethane clears. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.