Jump to content
Model Cars Magazine Forum

Recommended Posts

Posted

Even More Power!

I needed more room for the Big Hemi, so I cut out the engine compartment.

DSCN6743M_zps06e925ac.jpg

That should do it...

DSCN6747M_zps7759468f.jpg

More Coming... B)

Posted

Filling In...

I cut 2 lengths of plastic strip and glued them in the sides of the Engine Compartment.

DSCN6784M_zps81abf20a.jpg

Here is McScaren on the Chassis with the new Engine Compartment. Just enough room for the Big Hemi.

DSCN6786M_zps93907725.jpg

More Coming... B)

Posted

I always enjoy watching these creations fall out of your head and into reality. B)

Thanks Adam!

So glad you are enjoying it... B)

Posted

The Spoiler!

I decided to make a Spoiler for McScaren. I started with a piece of sheet plastic.

DSCN6792M_zpsf00d4564.jpg

Next I cut the Sheet Plastic down to fit. Then I sanded the bottom edge of the Spoiler so when I glued it on it was on an angle.

DSCN6799M_zps20e832e6.jpg

Rear View.

DSCN6804M_zps23aab37d.jpg

More Coming... B)

Posted

Nose Brace!

I added a couple plastic strips to the inside of the Nose. This will make a good Gluing Spot for the Chassis later.

DSCN6826M_zps03a8280b.jpg

Here it is with the Chassis in place.

DSCN6829M_zpsa81b4622.jpg

I am going to make a new windshield so I puttied up the old windshield grooves.

DSCN6836M_zps1e92aaa4.jpg

More Coming... B)

Posted

FLAIRS!

I cut the Fender Flairs off the ZZZZZ-28 Body so that I could add them to the McScaren Body. After a lot of Cutting & Fitting, I got a pretty good fit on the Rear Flairs.

DSCN6838M_zps115350b0.jpg

Pretty good fit on the other side too.

DSCN6843M_zpsefd57244.jpg

More Coming... B)

Posted

Front Flairs!

After a little Cutting and a lot of Fitting I found the right position for the Front Flairs. Here is the first one glued in place.

DSCN6851M_zpsaebeb555.jpg

Here is another view. I will be definitely be doing some more fitting and Cutting on this Flair...

DSCN6856M_zps5e5d0862.jpg

Rear View. Here are all four Flairs in place.

DSCN6858M_zpsa6bc7c4a.jpg

Tire Check! Here is a quick mock-up with some Deals Wheels Tires. I decided to use the DW Tires instead of the Die Cast GTP Wheels & Tires, because they are sooo Wide.

DSCN6865M_zpsc5d8487d.jpg

More Coming... B)

Posted

We Need More Vents!

I trimmed the excess from the Tops of the Front Flairs and the Backs of the Rear Flairs.

DSCN6867M_zps5d7b80f1.jpg

Next I trimmed a little more off the Front Flairs...

DSCN6869M_zps373eeea2.jpg

Then I filled in part of the Tops of the Front Flairs to form 2 more Vents.

DSCN6872M_zps7416afcd.jpg

After a little clean up, the cut-off Rear Flairs formed 2 more Half-Moon shaped Vents.

DSCN6878M_zpsc11e3a24.jpg

More Coming... B)

Posted

Side Panels!

I am going to build up the Side Panel with pieces of sheet plastic. This is the first piece, a triangular shape that fits between the Front & Rear Flairs.

DSCN6891M_zps17232ad0.jpg

Here is the second piece, the lower panel.

DSCN6892M_zpse4c20595.jpg

The third piece fits between the edge of the Front Flair to the bottom edge of the Side.

DSCN6894M_zps8cf2e46c.jpg

More Coming... B)

Posted

Holes & Gaps!

I cut 2 pieces of plastic to fill in the Nose Sides. Then I shaped them with a Drum Sander Bit in the Dremel Tool and Sanding Sticks.

DSCN6902M_zps786633be.jpg

Then I fit 2 Moon Shaped plastic pieces in the holes on the rear fenders and glued them in place.

DSCN6903M_zps7844703a.jpg

Applied some Putty.

DSCN6908M_zps6f465d85.jpg

Then I sanded it down with 220 sandpaper.

DSCN6910M_zps96bb0818.jpg

More Coming... B)

Posted

Prime Time!

Here are a few photos of McScaren after a couple coats of DupliColor Gray Filler/Primer.

DSCN6913M_zps730ad925.jpg

Rear View.

DSCN6918M_zpsd50804b0.jpg

Side View.

DSCN6921M_zps7ae0742b.jpg

More Coming... B)

Posted

2 More Scoops!

After the Primer dried I applied Putty to problem spots.

DSCN7010M_zps142589e5.jpg

Then I sanded the body smooth. Next I added the McLapper Side Scoops.

DSCN7014M_zpsb1309f00.jpg

I sprayed on a light coat of Grey Filler/Primer and let it dry in the Dehydrator. Then I sprayed on a couple coats of Flat Black Primer.

DSCN7022M_zps47fd143f.jpg

Rear View!

DSCN7028M_zps3d278c9b.jpg

More Coming... B)

Posted

Diamond Dust!

I sprayed on a couple coats of Testors Diamond Dust and let it dry in the dehydrator.

DSCN7030M_zps737e8a13.jpg

Top View.

DSCN7033M_zps5fef8994.jpg

More Coming... B)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...