Matt Bacon

I have the K&R XJ13. It's nicely detailed and makes up into an excellent replica that really looks the part. You need to know, though, that they are large white metal kits -- no plastic anywhere except for a vacform "glasshouse". You need to be happy cleaning up and building with white metal parts, and handling what's a pretty big and heavy model as you work on it. No doubt, though... when they're finished, they have real heft and "presence". bestest, M.

I have been hard at work with the cigarette foil (after a wander round the neighbourhood with eyes peeled to find some last night -- if you build cars, any time you see a discarded packet, grab it, take out the foil and bin the packet like the previous owner should have but you're glad they didn't...) I put the rear suspension bits in now -- the instructions would have you wait until all the engine pipework and cabin interior are in place, which to my mind is a recipe for undoing lots of hard work as you wrestle the upper wishbones into place! A triple whammy from Revell to watch out for here... 1) The instructions are badly drawn, and miss out that big ridge running fore and aft that you can see at the outboard edge of the opening in the wishbone 2) The parts have their numbers reversed on the instructions -- that ridge needs to go underneath, other wise it interferes with the springs which need to come out at an angle to reach their sockets in the wisbone 3) The pins that mount the wishbone are too long, so they don't fit horizontally out of the box As always, trial fit and adjust is the answer. The springs fit into sockets in the bottom side of those two blue and silver parts you can see on the pillars outboard of the rear of the engine (that's not clear on the instructions either). If you trim the pin on the wishbone that goes into the open slot towards the front of the car rather than the socketed one at the back, you can achieve a firm press fit by shaving a bit at a time until it slots in place. It's very hard to see whether you've got the wishbone horizontal in both planes. Bizarrely, Revell have moulded two fine lines on the interior surface of the wheel well, which are almost but not quite where you'd want them to be to line up the wishbone in two axes against them. Unless of course the instructions are wrong again and the wishbone SHOULD be angled... Getting started with the pipework. Owing to snappage as I was finely adjusting the relative positions of the pipes, I had to pin the outer pipes with to the inners with wire. This turned out to be a great idea, and I'd advise doing it from the beginning! I superglued the pin at one end, and used "Serious Glue" at the outer pipe end, so the pipe was free to rotate a bit for a few minutes. I also left the connection to the silencer as a press fit, so I had a bit of "wiggle room", but otherwise firm support. It's a testament to whoever designed this kit that with the mounting points held firmly, and that small amount of freedom of movement, the pipes dropped into their sockets on the turbos with minimal wiggling required. Four down, 12 to go... (there are two thinner exhaust pipes that thread between these, two intake boxes to the sides which connect to the front of the turbos, and two "overhead" air pipes which go on last, inboard of the turbos, and each one has to connect to two turbos...) Now I'm going to leave those pipe to set firmly for a few hours, and take a good look at the body for any polishing out of dust specks that's needed... bestest, M.

Thanks, guys! I've been playing around with some settings on the camera, just to see what happens, and used this as a test subject. You can see the colour properly, and get the impression of the wing in place. It looks lower and sleeker than I expected... Wheels done. Contrary to what I expected, you can actually make out the brake callipers, if you look REALLY hard. As so often in this kit, their are little touches of detail that are amazing -- you can actually read the "BBS" logo on at least two of the wheels. Shame that the plastic sagged a bit and filled with flash in places around the "spokes..." I hope these will help some intrepid future modellers battling this beastie. The spring, drive shaft and frame are a really tricky fit. You need to make sure that the frame is firmly rooted and square onto the undertray (which meant, in this case, removing some really weirdly located ejection pin towers inside the "shoulders" at the base of the frame which should fit neatly over the inner corners of the moulded wishbone). The drive shafts need to go well up into the sockets in the frame. And I had to slim down the upper spring locating pin considerably to get enough room for manoeuvre so that the spring didn't foul the drive shaft and lever the whole thing apart. The fit of the upper wishbones is really unclear from the instructions. I have no idea what, if anything, is going to fit onto those two pins on the top edge of the frame, but it ain't the wishbones. They clip into place with no inboard/outboard positive location, so just make sure the wheel carriers are vertical. The steering link goes with the ends angling towards the front. Oddly, although the shaft on the wheel carriers have "flats" to orient the wheels, the brake disk collars that fit onto them don't... And this is where I'm at tonight. I wanted the engine and exhaust silencer to be really firmly fitted to give me some solid anchor and reference points as I start trying to get all the tubing plumbed in around the engine, so they are glued in with "Serious Glue". The lolly stick lets me clamp the engine down firmly with tape while avoiding any pressure on the turbos lurking underneath... bestest, M.

I'm going to say real. Beautifully looked after and in concours condition, but real... bestest, M.

Brake discs waiting to go in. Look carefully, because you will never see these again, once they are inside the wheels! ...and now I have a shiny blue thing. The Zero 2K is "dust free" now, and I'll stick it in the airing cupboard to cure hard overnight. The rear spoiler bay and diffuser section are Zero's "Graphite Grey" -- I think it's carbon, probably, but on the pictures I have there's no visible weave pattern at all. bestest, M.

Thanks, guys! It all comes together pretty quickly now... et voila! My owner has decided on a non-prototypical walnut gear shift knob, for a bit more colour in the grey, grey and grey cabin... Now, back to the body and engine (one day I'll build a model in the order the instructions suggest, but... this is not that day) bestest, M.

Interior under way... A thing I did notice in pictures is how shiny (OK, "plasticky") the leather in the interior looks. Revell have also made some nice texturing on the seats. Outside, under lights, I know the shadows and highlights are overdone, but once they are inside a small and rather gloomy cabin, I still want the impression of texture to be visible. The dash is quite symptomatic of this kit. It has only two parts, yet OOB there's a big rectangular gap to the left of the binnacle which almost looks like a socket to glue something into. There's nothing there in the real thing though (or the kit parts), so I filled it with plastic strip and made it go away. On the other hand, there's some beautifully detailed engraving on the dials and controls, which comes up a treat when you paint and drybrush it. There's a decal, but I had no confidence of getting it to settle down over the detail, and I figured I could paint a better "burr walnut" veneer than the pixelated version on the decal. The wood effect is hard to see because the highlights from the gloss mask the grain, but I used Vallejo Woodgrain (transparent browny-red) over Cavalry Brown. A bit of research showed plenty of white labelling all over the instrument panel, which busys it up nicely. Won't be long before the cabin is finished now... bestest, M.

I have made a blue thing: Some small areas of other colours to add, and then it will be on with the SHINY... bestest, M.

Thanks, guys.... it's not the easiest of kits, but it's certainly not horrendous. The level of detail is pretty impressive, though it takes some work to clean up the parts because the mould is getting slightly tired. I'm progressing steadily in several areas, but only this to show for it so far... That's about it for the engine now. The exhausts and turbos are fixed using very strong, but flexible, "Serious Glue" which should allow a bit of room for manoeuvre when it comes to attaching all the pipework, of which there is a LOT. All I've added is a throttle linkage and return spring -- a bit overscale but it'll busy things up under there -- and the blue hoses coming out of the sides. To start work on the pipe work, I'm using the engine bay as a temporary jig. I want to get the pipework glued together into usable chunks before painting and then assembling permamanently. As well as these exhaust pipes, there are some smaller diameter secondary exhausts that have to fit parallel and around them, and then the air intake hoses that come over the top inside the turbos. All are provided, which is pretty impressive. The fit isn't brilliant though, which is less so... Template for masking up the window in the firewall behind the cockpit. It's not all glass under there, so I needed two identical, symmetrical masks. I made this out of cardboard, folded so both sides were identical, and then drew around it to create two masks from kabuki tape. A fair bit of swearing later, they were on opposite sides of the window... Body in primer. I should get the French Blue on tomorrow, now I've got the wing sorted as well... bestest, M.

Not something I'd build, either, but I think you can always learn more about modelling or pick up ideas from any dedicated modeller in any genre. Most of the techniques I use on car interiors come from figure painting, for example... bestest, M.

Announced a couple of days ago. Dedicated track car (think the Fxx or LaFerrari FXXK program) that they will build 24 of, and the inheritor of the One-77's mantle as by far the most bonkers car that Aston Martin has ever produced. 800 BHP from a 7-litre V12 without any of that turbo nonsense... bestest, M.

I'd buy it like a shot -- I've already got the colour matched paint from Zero, after all... bestest, M.

A great article in last month's Octane promoted this to the top of the build pile! It'll join the XJ220 and soon-to-be-built NSX in an "early 90s supercar" corner of the garage... The Revell kit is very nicely detailed, generally, but the mould is suffering, and this is NOT a car that likes to be packed in a flimsy box and sat on a shelf for years. Airfix/Heller do the whole cabin as a transparent piece that sits on top of the body, whereas Revell has gone for a roof and the flimsiest A-pillars ever committed to plastic. The body shell is also flimsy, and warped on my example, so I've assembled various "working" bits into one, much more solid, shell. The opening bonnet shows you little except the battery, but fixed in place it beefs up the front end nicely. And while it would be nice to have an opening engine cover, both it and the roof were warped. Fixing it shut lets me use the window between the cabin and engine bay as a solid "bulkhead" which pushes the roof and engine cover nicely back into shape... not quite figured out how the "wing" works yet. Heat shields covered with cigarette foil. They'll need a bit of fettling, but the texture is perfect... Wheels stripped of chrome. Lots of flash in the holes, so these are the "best of eight" -- I had a spare set from a donor kit I bough just for the tyres for £5, but the originals demonstrate how tired the mould is. It seems bizarre that they would chrome them in the state some of them were in, but there's obviously no intermediate quality check... The engine is nicely detailed, if a bit over complex -- I don't see a need to have the cylinder head in three stacked parts, especially when they don't fit very precisely, which can end up with your cam covers not aligned and not parallel, if you're not careful. If I was building another one, I'd set up (unglued) the base/sump part of the engine on the bearers in the big chassis part, and then glue on the block/head parts to the base, fine tuning their fore and aft alignment in the chassis, until I was sure that they run directly front to back, and then add the induction manifold and check that for alignment, all while the glue is soft. The blue detailing is prototypical, but there's a bit more to do to the throttle actuator rods yet... bestest, M.

I don't know who mark Taylor is either, but I agree with him. Make sure your plastic and primer coat have no imperfections, and then repeated light coats of Tamiya acrylics will do the job. Leave the paint for at least 24 hours in an airing cupboard or dehydrator, and it'll "shrink back" as it cures to leave no sign of surface texture. And if you want to, a polish with Novus "Fine Scratch Remover" polish will bring it to a lovely lustre: bestest, M.

Thanks, guys... don't worry, Gerry... I've decided what I'm going to do. This one will have to be built "closed up" There's a big window to see the engine detail through, but the opening engine cover is part of the problem -- there's not enough structure around the cabin to hold everything in place unless it's fixed. It'll look OK, I'm sure! bestest, M.

...has anyone built one of these or got a "known good" one in the stash that they could take a look at? I'm just starting one, and I'm a bit worried at the state of the main body parts. I assume that they should be kinda symmetrical, but the engine cover and the main cabin seem to be a bit "sideways". In particular, the spindly "A" pillars are very curved. Looking at my references, they probably should have some curvature, so they may be OK... I think, whatever, that I'll be gluing the engine cover in place to help "solidify" the body... there's a big clear window in there so you can see the engine properly, and the value of the "working" feature seems limited... If anyone can give me a solid read on what the body SHOULD look like, I'd be very grateful! bestest, M.

Hi, Shay... it's this stuff: http://www.hiroboy.com/catalog/product_info.php?products_id=3534 It's a bit weird to spray, but as you can see, it does the job very well! bestest, M.

Thanks, gents! ...and here's Harry's: bestest, M.

A nicely detailed, straightforward curbside kit that really captures the look and stance of the pugnacious original. Zero Paints colour matched Giallo Ginestra and 2K Clear Coat. Why not red? Because I nearly bought one of these in my mid-20s, until I discovered how much it would cost to insure (that and the fact that the "seller" didn't have ANY of the paperwork for the car, which worried me even more than the insurance). Still, it's one of the few models I've built of a car that there's any possibility of me owning, ever... Those of you who followed the build will know all about the paint; if you didn't, the clear coat solvent managed to leach the red dye from the bodyshell plastic right through the primer and the yellow base coat, and turned orange. This has been stripped, sealed with oxide paint sealer, and then primed and painted a second time. The only other tricky bit was getting the chassis inside the body shell, which is a "once and for all" deal, with some extreme flexing of the body required... bestest, M.

Thanks, chaps... I'm calling this done now. Better pictures to follow when I can break out the "studio" (and find a feather to clean the inside of the windscreen!) What a great little kit, even if I could have done without the red plastic bodyshell! bestest, M.

So, that was one of the more nerve-wracking episodes of putting the body on the chassis. Talk about "tight fit"... Now all I have to do is figure out how to dislodge the small flakes of yellow paint that have pinged off the body or chassis and static-electricity-ed themselves to the windscreen and side windows. I need a feather! bestest, M

Thanks, chaps... slow but steady progress... A couple of hours masking, ten minutes spraying, and 30 minutes clean up! And what's this interloper on the bench? One I'm saving for later... bestest, M.

Thanks, all... This has taken a while, but now I'm back where I started! Stripped, sanded, coated with sealer (the greeny-yellow stuff), primed again in white, shut lines washed in black with Citadel wash, and finally repainted in the Zero yellow base coat. It is rougher than it would have been if I'd got it right first time, here and there, but it's a balancing act between getting it completely smooth and sanding away the surface detail you want in some places... ...and just in case anyone was wondering why I like the Zero 2K system, despite the fact that it's poisonous and a real faff to clean up after, this is it. I've done no polishing at all on the roof or bonnet here. Not even had to take out the odd dust mark... Bearing in mind that there's satin black trim to go all over the place, but especially around the windows, I'm pretty happy how this has turned out straight out of the spray booth. There's no red bleed anywhere, except for one small and inexplicable circular spot on the rear bumper... bestest, M.

I know what it is, too... .... it is truly, spectacularly, irredeemably AWFUL. Now I just need to give it a name. bestest, M.

The i8 and 918 "Weissach" look fantastic. They took the easy way out with the i8 colour scheme... I'll be building mine more like this: ...but the 918's easy. Just swap the black for gloss white, and I'm done... bestest, M.