bbowser Posted November 9, 2017 Share Posted November 9, 2017 I did this as a slump buster. Was disappointed when I opened the box and found no decals, just stickers. Surprisingly they went down pretty well and conformed to curves better than I expected. I am looking forward to the full detail kits of the Ford and Chevy, I have not picked up either yet. Comments welcome, thanks for looking. Quote Link to comment Share on other sites More sharing options...
MarkJ Posted November 9, 2017 Share Posted November 9, 2017 Great job , Bob . I'm not sure, but I think those stickers have a top layer you remove after you apply them that cleans them up a bit. I found this out when I was using the upper grille sticker as a template for the one I'm building at the moment.. Maybe somebody can voice in on this if it is the case. Quote Link to comment Share on other sites More sharing options...
martinfan5 Posted November 9, 2017 Share Posted November 9, 2017 Nice work on the slump buster Quote Link to comment Share on other sites More sharing options...
MarkJ Posted November 10, 2017 Share Posted November 10, 2017 I tried another sticker on an old 63 chevy body and yes I believe they want you to remove the outer film from the stickers and then clean off the gooey stickum between the image and the outer film with 70 % isopropyl alchohol. This makes the sticker look more like a decal. see the pictures below. just get the outer film loose with your fingernail and pull it off with a tweezers it sticks pretty hard but the image does look better with the outer film removed. Quote Link to comment Share on other sites More sharing options...
bbowser Posted November 10, 2017 Author Share Posted November 10, 2017 Thanks Mark, I'll give that a try. I may end up peeling them all off and getting a real decal set anyway. Call me a sadist but I like decaling a stock car! Quote Link to comment Share on other sites More sharing options...
MarkJ Posted November 11, 2017 Share Posted November 11, 2017 Ok, Bob. Sounds good. Sorry I kind of hijacked your thread but I think a lot of guys might not have known about removing the outer layer of the stickers. It leaves a much smaller edge and if the body was cleared after the process the stickers would really look like decals. Quote Link to comment Share on other sites More sharing options...
bbowser Posted November 11, 2017 Author Share Posted November 11, 2017 No problem Mark, always open to suggestions, especially from as gifted a builder as you. And it's Bruce BTW Quote Link to comment Share on other sites More sharing options...
MarkJ Posted November 11, 2017 Share Posted November 11, 2017 No problem Mark, always open to suggestions, especially from as gifted a builder as you. And it's Bruce BTW Sorry bought that Bruce, I used to work with a guy named Bob Bowser and I guess I had a senior moment. Thanks. Quote Link to comment Share on other sites More sharing options...
donb Posted November 12, 2017 Share Posted November 12, 2017 Nicely done Bruce. Looks really goof Quote Link to comment Share on other sites More sharing options...
towman1271 Posted November 12, 2017 Share Posted November 12, 2017 looks great Quote Link to comment Share on other sites More sharing options...
Silver Foxx Posted November 15, 2017 Share Posted November 15, 2017 A nice looking build , well done . Quote Link to comment Share on other sites More sharing options...
Old Coyote Posted November 16, 2017 Share Posted November 16, 2017 A very nice build Bruce .............. quite impressive ! Quote Link to comment Share on other sites More sharing options...
slusher Posted November 19, 2017 Share Posted November 19, 2017 Really nice build Bruce! I have similar kits for slumps... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.