nitrojoe Posted January 15, 2007 Share Posted January 15, 2007 ok, tell me some idea's how to make my own wheel tubs for model kits that have stock rear tubs that i want to make into drag cars. Quote Link to comment Share on other sites More sharing options...
Stingray69 Posted January 15, 2007 Share Posted January 15, 2007 Well first off you're going to have to figure out how big of tires you want. 9 times out of 10 you will have to narrow the rear section of the frame for a set of slicks to fit. This usually can be done cutting off the rear portion of the frame, adding a new crossmember, and then a new narrower rear sub frame. After thats done you can make your tubs. I personally like to use metal because its easy to form and it holds it shape. With plastic you'll need a heat source to get the tubs to hold there shape. One trick that helps in the process is to make a template first... index cards work well here. Once you got the template to fit ok transfer it to the metal or styrene. You'll still need to trim a bit to get a good fit. Once one side is done its only a matter of tracing the pattern again. Don't be surprised if this takes some trial and error... it'll take plenty of paietence. This is a set of "mini" tubs I built for an Outlaw 10.5 Corvette i'm working on... there's still some work that needs to be done on them (notice the tubs aren't perfectly flush with the body, that drives me nuts!!) but hopefully this will give you a clearer picture with the explanation above. Another option you have is to find an already "tubbed" kit. The Revell 67 Chevelle Pro Street is great for this or the AMT 70 Superbee Pro Street. These kits already have the work done its only a matter of getting them to fit by trimming the tubs. You can also just cut off the rear portion of the frame and mold it to any other frame you want. Hope this helps some!! Quote Link to comment Share on other sites More sharing options...
bob paeth Posted January 18, 2007 Share Posted January 18, 2007 In making trailer fenders I inadvertantly came upon the solution for wheel tubs also. After all they both have the same shape, just that one goes on the inside and the other goes on the outside. The process takes a bandsaw or very careful work with a coping saw. All you need to do is find a piece of wood, a 3/4 X 4" X 4" for instance and trace the wheel on the surface of the wood. Then cut along the line. When finished you will have two pieces. The saw blade will give you a gap when the two pieces are put together again. Then take a piece of styrene and "sandwich" in between the two pieces and force them together. Heat your oven to 350 degrees. When the oven reaches temperature, put your project in and give it about 15 minutes. Then, take it out and let it cool. You now have a wheel tub ( or fender ). Repeat again for the other tub ( or fender ). bob :shock: Quote Link to comment Share on other sites More sharing options...
astroracer Posted January 19, 2007 Share Posted January 19, 2007 Another option is swapping chassis. Kit bashing. Many of the Pro-Street, Pro-Mod and Pro-Stock kits have nicely done chassis which will fit under other cars with little to no modifications. Find a kit which is similar in shape and wheel base and you will be on the right track. As an example: I started building a Pro-Mod style '71 Satellite. I used the Revell Red Hot Pro-Stock Thunderbird chassis under it. It fit like a glove, even the roll cage, with only the addition of some sheet stock in the rear wheel wells to flush it out to the wider Satellite body. Mark@MAS www.mas-parts.com Quote Link to comment Share on other sites More sharing options...
ViriiGuy Posted February 14, 2007 Share Posted February 14, 2007 I know this is a little late, but a good way I have found to tub out wheel wells is to use prescription pill bottles. A buddy of mine gave me this tip a while back. Find a pill bottle that is a little bigger than your wheel, cut it to width, and then cut it in half. You will have wheel wells for both sides of the model VG Quote Link to comment Share on other sites More sharing options...
bobss396 Posted February 22, 2007 Share Posted February 22, 2007 Try harvesting the wheel tubs out of a stock car kit, those are pretty big and you could probably razor saw what you want out of it fairly easily. Bob Quote Link to comment Share on other sites More sharing options...
41CHEVY Posted March 15, 2007 Share Posted March 15, 2007 :idea:I went to the local home center (HOME DEPOT) and got a scrap piece of the 1 1/2" thin black plastic pipe.It's got a very thin wall and can be glued with Zap or any other type of "crazy glue" or Plastruct liquid works fine. Paul Quote Link to comment Share on other sites More sharing options...
mark wheat Posted August 26, 2014 Share Posted August 26, 2014 i use a soda can i cut it open first then flatten it out then take a small piece poster board roll it & trim it to fit with scissors &before i roll it i polish it out Quote Link to comment Share on other sites More sharing options...
Jantrix Posted August 26, 2014 Share Posted August 26, 2014 Try a pill bottle. Quote Link to comment Share on other sites More sharing options...
scalenut Posted September 14, 2014 Share Posted September 14, 2014 the 5hr energy drink bottles work great for the pegasus 22 size wheels Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.