MoparWoman Jamie Posted September 13, 2013 Author Share Posted September 13, 2013 Th double mark lines in the rear, one is for the interior, the second one closer to the center is the tilt downwards one of the floor pan from the rocker/interior level Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 13, 2013 Author Share Posted September 13, 2013 A few exterior mock ups Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 13, 2013 Author Share Posted September 13, 2013 Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 13, 2013 Author Share Posted September 13, 2013 In this one, you can see how far I tilted the center floor pan piece forward The mock up with the tail panel held in place Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 13, 2013 Author Share Posted September 13, 2013 The floor pan.. I'm hoping to maybe have a metal floor pan stamp by the weekend I hope you all enjoyed the progress update photos, all comments about the project is welcome, an I'll try to answer any questions best as I can if I see them Quote Link to comment Share on other sites More sharing options...
beeRS Posted September 13, 2013 Share Posted September 13, 2013 Some amazing work there on getting the sub-chassis right. Great scratch building skills. Keep up the great work. Quote Link to comment Share on other sites More sharing options...
doggie427 Posted September 13, 2013 Share Posted September 13, 2013 WOW !!! Quote Link to comment Share on other sites More sharing options...
Belugawrx Posted September 14, 2013 Share Posted September 14, 2013 absolutely amazing work I will follow Quote Link to comment Share on other sites More sharing options...
Car Man Posted September 14, 2013 Share Posted September 14, 2013 nice car but not so nice finger nalis Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 16, 2013 Author Share Posted September 16, 2013 Hi you all, well I'm working on the rear roof pan that is just under the rear seat. My wife when she was at the local hobby shop the other day. She picked me up some extra chassis's that was broken here an there that was also charger chassis. So I been working with the one as a parts donor. I just about got the pass side rough out in shape. Anyways, I'll let the photos do the talking here. LOL Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 16, 2013 Author Share Posted September 16, 2013 Had to lower the tranny hump 1mm down Yep, had to slipt it as well and bring it in about 2mm Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 16, 2013 Author Share Posted September 16, 2013 I removed to much so had to fill in some I was cleaning some glue off the back piece here Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 16, 2013 Author Share Posted September 16, 2013 Checking to see how things look and if they line up Yep. now I had to chop the pass side part to bring it in 2mm about Now after I got the other area done, was time to take care on the pass side outer piece now. Sine I going to redo the wheel wells with more correct ones from the other chassis. I cut into this one. I am keeping all piece to glue back together though so I can maybe use them later down the road Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 16, 2013 Author Share Posted September 16, 2013 New piece of floor pan in the making here Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 16, 2013 Author Share Posted September 16, 2013 I hope you have enjoyed the update here. All comments towards the project is welcome. Any questions ask, I will try to answer best as I can if I see the question. Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 20, 2013 Author Share Posted September 20, 2013 I been busy with this one. Since the last update. I did get quite done to the one side. I got the area in primer, got the other side done as well. It's till in rough stages yet. Yes, the driver side area is a mm to tall.. I took care of it though later on Here I'm staring to work on the driver side floor pan area next to the frame rail Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 20, 2013 Author Share Posted September 20, 2013 All button up now Had to lower a few areas Started to add some detail to the rear floor pan area under the rear seat area Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 20, 2013 Author Share Posted September 20, 2013 Here is a better photo of the underside Primer time again Right after those photos was taken, I corrected the rear wheel well height on the driver side, plus I also felt the drain holes in the area under the rear seat area was too small so I engraved the circles a little bigger. I hope you all enjoyed the update, all comments towards the project is welcome Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 23, 2013 Author Share Posted September 23, 2013 Okay, heres an update. Filled the center area with superglue Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 23, 2013 Author Share Posted September 23, 2013 Some sanding to shape things up Okay I gave it a good coat of primer.. okay okay, I layed it on Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 23, 2013 Author Share Posted September 23, 2013 Still have this side to reshape yet Okay, sanded things down to level a few things out Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 23, 2013 Author Share Posted September 23, 2013 Okay, here is some details. The small holes is the drain plugs, the real floor pans also have these to. I still have to add a few more yet plus make a few other od and ends too that will attach to the metal version of the model pan down the road. Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 23, 2013 Author Share Posted September 23, 2013 I got to work on this area yet Did a little more sanding As you can maybe notice, I bought the center rear area forward 1mm from where it was at before I still have to add the ribs yet on all 3 panels yet and also make the locking lip on the very front area piece as well. Then make all the little plates, plus add the square piece to the tunnel hup. Then I can move to the wheel wells and rest of the trunk pan. I hope you all enjoyed this update, comments towards the project is always welcome. Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 24, 2013 Author Share Posted September 24, 2013 Okay, spent last evening engraving details Keep in mind, this all is still rough stage yet Some little scalping Bolt plate holes was drilled out or marked out Quote Link to comment Share on other sites More sharing options...
MoparWoman Jamie Posted September 24, 2013 Author Share Posted September 24, 2013 Here you can see the panel accents or what ever they are called Primer time to see what areas I still need to work in yet I hope you all enjoyed the update, any comments towards the project is always welcome. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.