chepp

.

Sorry for the delayed response. I mostly use Tamiya X prefix acrylic paint and these Badger paints: Stynlrez primer (black, white, gray) -- The brand means it's made for styrene, vinyl and resin surfaces. Model Flex, Minitaire I also have a stash of long-out-of-production model railroad water-solubles such as Polly Scale. I use the water-soluble term to describe what probably are acrylics (but don't always have that description on the label) that can be thinned with water. Other generic names are water base and water cleanup. However, for Tamiya I use their X-20A for thinning. For Badger and others I use this home-brew thinner formula: 6 oz. distilled water, 4 oz. universal acrylic thinner, 0.75 oz. retarder and 2 drops of Kodak Photo-Flo. However, when I use up my current brew I'll probably use Vallejo Airbrush Thinner 71.161. For airbrush cleaning, I use tap water followed with Badger Spray-Thru Airbrush Cleaner.

Back to the original question, for paint in bottles (brushing and airbrushing) I've almost exclusively only purchased water-soluble ones in the past five+ years while continuing to use spray can (solvent based) but buying fewer spray cans than before. I still have some solvent-based bottle paints that I mostly use for brush painting but sometimes for airbrushing. I'm "using them up" as I transition to water-soluble ones. My reasoning for going to water-soluble ones is that I'm concerned about health issues that might result from the fumes of the solvents. For airbrushing either kind I wear a NIOSH filter-mask to protect against both the fumes and micro-particles. I tend to avoid the cheap craft paints unless it's a special color, such as pearl yellow. Instead, I usually buy Tamiya or Badger brands.

Both the photo on the cover of the box and on the instruction sheet show a post sedan but the kit is clearly a hardtop.

Thanks! I don't have a sub so I bought a single copy -- $11! It's an entire issue of weathering techniques. The price is kind of steep but it was worth it to see step-by-step examples with explanatory text. For example, I'd heard of chipping fluid but I had no idea about what it was until seeing this.

Thanks again for the kind comments. However, I mistakenly jacked up the rear too much. Since it's a curbside model, a quick cut to my snap-in rear axle holder brought it down to still have a California rake but one that is much more traditional.

Thanks for finding and posting this. That radical kustom '58 Ford must have been something to see driving in traffic! After 12:40 the video shows a fellow with revolvers doing some quick-draw shooting at cans -- who was he?

Thanks, all, for the kind words. As always, I'm open to constructive criticism, too. Here's my build thread on a different forum: https://trakinscale.proboards.com/thread/20012/1961-pontiac-ventura-kustom .

Thanks! Well, just a vague idea for the Riv as a sectioned topless speedster with a short windscreen and tonneau covering most of the interior. I'm building a series of 1/25 rods and customs that could have been built in 1:1 from the late '50s to the mid '60s. The operative word is "could" because although I'm using traditional era-correct parts and mods I have the benefit of hindsight to look like I was predicting the future such as the big beak on this '61.

Thanks! Actually, they are chrome but they do look clear from some angles. Here's a video that shows the car, and interior, rotating that shows it better:

Here's a curbside kustom I've just finished. It started as a Moebius 1961 Pontiac Ventura hardtop. Bbbbb-but, a '61 doesn't have that roof. You're right. It's from a '63 Riviera. Paint is Tamiya Clear Green over metallic silver and areas of pearl white with various colors of fogging.

Here's a military modeler's DIY: https://d6combat.com/diy-washes-contrast-paint/ I haven't tried it but it appears to be OK. I use Kodak Photo Flo (prevents water spots on water-rinsed photo film) for making "wet water" on diorama scenery* -- it performs the same function as dish detergent except that it doesn't have degreasing, fragrance, etc. ingredients. *It keeps thin water/glue solutions from beading up, it is not used to simulate water.

PM'd

I've just discovered this thread and have some other projects in the works. Something just "called" to me about a week ago, though, and I ordered the chopped/filled body and stock firewall from Drag City Castings. All I'm sure of is that it won't be a modern street rod with air suspension, billet nor rubber-band tires...and it won't be a rat rod, either.