gasser59 Posted January 8, 2012 Posted January 8, 2012 (edited) The StraightLine Modelers group is doing a community project of gassers and I wanted to join in on this so here's my build. I picked up a cab body from a SLM member and am using the bed and some of the components from the AMT '40 Willys coupe and pickup kit. As you can see, the bed is taped together for the moment and I'm currently working on the working scratch built straight axle. This will help determine ride height. The picture shows the truck a bit too high at the moment. May need to either re-arch the front leafs or make new ones. Â Thanks for following along and comments welcome. Â Â Edited May 17, 2017 by gasser59
Dr. Cranky Posted January 8, 2012 Posted January 8, 2012 You've mocked it up with the right look, I can't wait to see more.
a/gass Posted January 8, 2012 Posted January 8, 2012 drop the rear for sure the front is close - to get the front correct the center of your engin crank (or bottom pully- harmonic balncer)cant be no higher than 24 mm (or 2 foot in real life) any higher and its a street freek or not track legal. hope this helps you some.
W-409 Posted January 8, 2012 Posted January 8, 2012 Looking really good so far. Front axle work is incredible. Great to see '41 Willys Pickups too, and with your building talents this is going to be really great. Can't wait to see more.
gasser59 Posted January 8, 2012 Author Posted January 8, 2012 (edited) Thanks fells especially Michael. I lowered the engine mounts a bit and I'm right at 24mm. Progress continues... Edited March 27, 2017 by gasser59
rustybill1960 Posted January 8, 2012 Posted January 8, 2012 Great Subject!! Like what I hear and see! Thank You for sharing Later Russ
Mooneyzs Posted January 9, 2012 Posted January 9, 2012 Brad... this is going to be a killer model my friend. I will be following this build for sure. I can't wait to see what you have in store with it.
eviltwincustoms Posted January 9, 2012 Posted January 9, 2012 Very cool build, I have always like the Willys be it a car or truck. Definitely will be peeking in on the progress of this one!
Jantrix Posted January 9, 2012 Posted January 9, 2012 drop the rear for sure the front is close - to get the front correct the center of your engin crank (or bottom pully- harmonic balncer)cant be no higher than 24 mm (or 2 foot in real life) any higher and its a street freek or not track legal. hope this helps you some. Great info! I always wondered what the difference was. Thanks very much. The Willys looks like a great project. Looking forward to seeing more.
Truck parts Posted January 10, 2012 Posted January 10, 2012 That is off to a great start. Looking forward to seeing it done.
gasser59 Posted January 13, 2012 Author Posted January 13, 2012 Been continuing working on the straight axle and its mostly done. Thought I would share with you how I do this with photos and a brief description. Below is the rough cut of the steering knuckle cut from 3/16" square aluminum tubing as well as the axle cut from 3/32" OD round tubing with the T in place. The T has had a piece of wire insulation inserted to take up some of the slack once the metal pin is installed at the end. This next pic shows the knuckle cleaned up, rounded off and the holes drilled out for the spindle and the pin. at this point, I've glued in the pin for the spindle tubing. I use X-Acto handles with the two cross slots in the head to hold my drill bits and drill these holes by hand. Up next is the 1/16" aluminum tubing has been added over the metal pin for the spindle. Next, I need to add the steering arm to the knuckle. Again, I use piano wire that has been shaved on the edge of my cut-off wheel on my Dremel Stylus. It also has a slight bend in it that faces away from the knuckle. Here's the steering arm glued in place with the rod end in place. In this case, I used plastic ends from the parts box, I think they're from a sprint car kit. This plastic piece was drilled out for the steering arm to fit into. Finally, here's the knuckle in place with a temporary pin holding it in place. Before attaching the knuckles, I used a polishing cloth to shine up the aluminum to resemble chrome. Final piece to make is to make the tie rod that connects the two knuckles together. Stay tuned and thanks for following along.
John Pol Posted January 13, 2012 Posted January 13, 2012 Wow nice job so far what do you use to glue it altogether with? John Pol
Jon Cole Posted January 13, 2012 Posted January 13, 2012 Such quality work is humbling. Thanks for sharing this.
gasser59 Posted January 13, 2012 Author Posted January 13, 2012 Thanks for the comments fellas. I use green label Zap-a-Gap exclusively on my metal to metal and metal to plastic parts.
brett Posted January 13, 2012 Posted January 13, 2012 Excellent little tut Brad, thanks for sharing it
gasser59 Posted January 14, 2012 Author Posted January 14, 2012 After work, I was able to fabricate the tie rod from stainless stell tubing from RB Motion and another piece of 0.015 diameter piano wire that's bent at the ends to go into the steering arms. The hole in the steering arms were filled with another piece of wire insulation but much thinner. This should allow the wire ends to pivot without coming out.
JB_Hobbies Posted January 14, 2012 Posted January 14, 2012 Great start! nice job on the front end too! JB
gasser59 Posted January 16, 2012 Author Posted January 16, 2012 A bit more progress over the last couple of days. Front axle is done, the chassis is painted and the Cragars and some of the engine components have gotten a shot of Alclad. I changed all of the tires and am happy with these. The pie crusts were too short for the ride height. Still deciding on an injection system. May go with the Enderle as shown here but it seems a bit out of scale. Its sitting upside down for the picture. As always, comments welcome and thanks for following along.
eviltwincustoms Posted January 16, 2012 Posted January 16, 2012 (edited) After work, I was able to fabricate the tie rod from stainless stell tubing from RB Motion and another piece of 0.015 diameter piano wire that's bent at the ends to go into the steering arms. The hole in the steering arms were filled with another piece of wire insulation but much thinner. This should allow the wire ends to pivot without coming out. Great Job with the moving parts very nice ingenuity you got going on... Ok, so I have to ask, and maybe this is obvious for others. Me being captain obvious, I just have to ask. LOL you bought SS rod from RB motion, why didnt you purchase the Rod Ends and some scale hardware and washers? This way the turning functionality would be butter smooth and not catch when it rotates due to the bent wire. Edited January 16, 2012 by eviltwincustoms
gasser59 Posted January 16, 2012 Author Posted January 16, 2012 OK, Cap'n Obvious. I already had the tubing and ran out of rod ends. They're on my to-do list.
eviltwincustoms Posted January 17, 2012 Posted January 17, 2012 OK, Cap'n Obvious. I already had the tubing and ran out of rod ends. They're on my to-do list. Thanks Brad, I needed a laugh at the whole "Captain Obvious" thing this morning. I hear you about running out of these darn little things.... having to purchase more and then the waiting part just kills you.
gasser59 Posted January 19, 2012 Author Posted January 19, 2012 (edited) Ain't that the truth. Doesn't help either that I haver several builds going on right now. Something I try to avoid. Edited January 19, 2012 by gasser59
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now