'F O R D ' hood lettering ?

[jdcar32]

Chrome foil this small won't stick and my hand lettering is not good. Wondering about a decal source from other kits that might provide 'F O R D ' lettering for the hood. As far as that goes, hood / trunk lettering is usually an issue if a  p.e. set is not available. Ideas ?

[sidcharles]

there's a current thread about aftermarket lettering sources.

something you might consider is using a pencil eraser dampened with paint (not dripping) and stamp each letter.

search for that thread; it has some good responses.

Q: is this a police car?  fog lights have piqued my curiosity; thanks.

[Shark]

I have used the artist type colored pencils on similar situations. They make a bright silver. I sharpen it normally, touch it to my tongue to lightly moisten it, then go over the item to color with the side of the pencil tip.

[Can-Con]

A lot of the current Ford kits have hood lettering decals. 

The AMT '66 Mustang GT had 2 sets on the sheet. IIRC, all the Moebius Ford pickups have hood lettering decals etc.

Also there are a lot of Model Car Garage PE sheets with the hood lettering. Doesn't have to be specifically for the '49 to have lettering that would work for that lettering.

[jdcar32]

7 hours ago, sidcharles said:

there's a current thread about aftermarket lettering sources.

something you might consider is using a pencil eraser dampened with paint (not dripping) and stamp each letter.

search for that thread; it has some good responses.

Q: is this a police car?  fog lights have piqued my curiosity; thanks.

that's a good tip, I may try it. I added the fog lights 'cause I thought the car needed some color, they were a typical add on then.

[peteski]

I think the best solution would have been to apply patch of Bare Metal foil to the lettering after the primer coat, then spray the top color, then remove the paint from the raised lettering exposing the metal foil.

There are members on this forum who have successfully done that and it looks really good. @StevenGuthmiller is one of them.

[mcs1056]

I saw a video wherein the builder wetted a business card with paint and used that to touch just the tops of the emblems. 

[Bills72sj]

6 hours ago, peteski said:

I think the best solution would have been to apply patch of Bare Metal foil to the lettering after the primer coat, then spray the top color, then remove the paint from the raised lettering exposing the metal foil.

There are members on this forum who have successfully done that and it looks really good. @StevenGuthmiller is one of them.

I too have used the foil UNDER paint method.

[Straightliner59]

I'm not sure if you can really see the emblems below the taillights, here, but...I had intended to use the foil under paint to do them. I forgot the foil, before the paint. So...I foiled them, afterward, and trimmed them as closely as I could, then flowed some of my remaining paint around, and over the emblems. It actually worked out pretty well. It's difficult to tell that I was forgetful!

[StevenGuthmiller]

16 hours ago, peteski said:

I think the best solution would have been to apply patch of Bare Metal foil to the lettering after the primer coat, then spray the top color, then remove the paint from the raised lettering exposing the metal foil.

There are members on this forum who have successfully done that and it looks really good. @StevenGuthmiller is one of them.

I’ve been using this method for many years and I have had great success.

Even the smallest scripts and badges can be done using this method, and once completed using foil, you have the added bonus of being able to detail small badges very intricately with paint.

Something that can be very difficult to do with markers, pens or paint brushes.

Just my opinion, but once you understand and master the “foil under paint” technique, there is not much else that even comes close.

 

 

 

Steve