62rebel Posted January 7, 2012 Posted January 7, 2012 no pics needed. it's the same '55 Nomad that's been there; well; except for the back of the rear seat. and ALL of the performance/custom parts. well; except for the drag front crossmember; it's still there. none of the "El Camino" conversion parts are there; the rest of the tube front axle is gone; not even a second set of wheels or tires. this might be the only '55 Nomad in circulation at the time, and as such, if you want a showroom stock one, you're in luck. the rest of the parts are actually pretty cleanly molded except for the chrome wheels; they have some flash issues that will pose trouble when cutting them off the sprue. no wonder that RC2 didn't bother printing the box contents on the bottom of the box.
Eshaver Posted January 7, 2012 Posted January 7, 2012 (edited) Sad............................................................................................................................................................... Edited January 27, 2018 by Eshaver
Edsel-Dan Posted January 7, 2012 Posted January 7, 2012 Have they returned the front Brake backing plates to the tooling yet?? They lost them when they added the inserts to this tooling for the Sedan.
62rebel Posted January 8, 2012 Author Posted January 8, 2012 no, there are backing plates but the instructions call them out as intended for the rear axle; odd, considering that the rear axle is still on the chrome tree and the backing plates are not.... which, in a convoluted way, tells me that they may as well be used on the front. the omission of the finish panel for the back seat aggravates me... duplicating that rear deck pattern on a piece of styrene isn't going to be easy. i'm tossing in the performance parts from the '55 sedan that i didn't use on the gasser.... and the better set of wheels as well. the front seat confuses me, since in the sedan AMT seemed to put in at least SOME effort to make it look presentable. as a STOCK kit, it doesn't disappoint me that much. but, knowing what USED to come in the box, it ticks me off just a hair.
Edsel-Dan Posted January 9, 2012 Posted January 9, 2012 The rear plates were always there There were 2 sets. neither were chrome I got lucky in the rear seat panel I had a scrap interior that I cut a section out to make the insert I added the chrome/aluminum surround with Evergreen strip
1972coronet Posted January 9, 2012 Posted January 9, 2012 It'd be nice if Round2 could restore the original tooling and toss-in their superb "pie crust" pad print tyres ...
Rob Hall Posted January 9, 2012 Posted January 9, 2012 Wasn't there a Boyds or Rides issue a few years ago also? I don't know how complete it was... I have the original issue and one from the '80s.
62rebel Posted January 10, 2012 Author Posted January 10, 2012 it's odd, again; that the Nomad still has witness marks for the guidelines for cutting the rear wheel wells out, and the '55 Sedan does not have them.....
Rob Hall Posted January 10, 2012 Posted January 10, 2012 it's odd, again; that the Nomad still has witness marks for the guidelines for cutting the rear wheel wells out, and the '55 Sedan does not have them..... I don't know if the sedan kit ever had them...it was tooled up at least 25 years after the Nomad was.
Junkman Posted January 10, 2012 Posted January 10, 2012 (edited) Since when is the back of the rear seat missing? I have a WIP from what I believe is the issue from the red box with the pastel green model, and it's missing from that one, too. I thought the kit is just incomplete. Man, I wish they'd re-issue the 1/16 scale one, too. Btw. I really like your phrase 'half-reissue'. Very funny and very appropriate. It should make it into popular folklore and used to slag the manufacturers. Edited January 10, 2012 by Junkman
dodgefever Posted January 10, 2012 Posted January 10, 2012 It'd be nice if Round2 could restore the original tooling and toss-in their superb "pie crust" pad print tyres ... Agreed. I'll be giving the "half-reissue" a miss.
Edsel-Dan Posted January 11, 2012 Posted January 11, 2012 The front Brake drum backing plates & rear seat insert were lost when AMT tooled the body & interior for the Sedan. Upon re-issuing the Nomad those part never returned. I bought the "W-M Value-Decorated" aka Pro-Shop version of the Nomad and they were not in the box. Hopefully Round2 will get the notice about the missing parts and fix this kit soon.
deathskull59 Posted January 12, 2012 Posted January 12, 2012 or couldint you just cut the rear seat off of the nomad inter. and make it in to a sedan delivery instead. since their is no part for it and you cant make it in to the elcamino custom any more. like in the amt jonny lighting kit. becus. in that kit had all of the custom parts.
Chuck Most Posted January 12, 2012 Posted January 12, 2012 Wasn't there a Boyds or Rides issue a few years ago also? I don't know how complete it was... I have the original issue and one from the '80s. That had no stock tires (it might have had the stock wheel covers and inner wheels- NOT sure). It did have all stock and custom parts, it just had some really poorly done big-inch wheels included.
jparsons1969 Posted February 29, 2012 Posted February 29, 2012 I was really pumped to put this model together. This is the Boyd Coddington model kit. But like you said, the rear panel of the back seat is missing and looks really retarded that way. I had some major fitting issues while assembling the body to the chasis and had to move the engine toward the front just enough that it made the the driveshaft not connect to the transmission. Needless to say I was pissed. Also had a very brittle king pin break while assembling the tie rod, but got it rigged up anyway. I had to get up and leave the kit several times so I wouldn't smash it to pieces. Overall the kit looks pretty good until you flip it over and see a non-functioning drive shaft.
Guest Johnny Posted February 29, 2012 Posted February 29, 2012 I was really pumped to put this model together. This is the Boyd Coddington model kit. But like you said, the rear panel of the back seat is missing and looks really retarded that way. I had some major fitting issues while assembling the body to the chasis and had to move the engine toward the front just enough that it made the the driveshaft not connect to the transmission. Needless to say I was pissed. Also had a very brittle king pin break while assembling the tie rod, but got it rigged up anyway. I had to get up and leave the kit several times so I wouldn't smash it to pieces. Overall the kit looks pretty good until you flip it over and see a non-functioning drive shaft. A little bit of sprue the same size as the drive shaft will fix that right up.
Edsel-Dan Posted March 1, 2012 Posted March 1, 2012 Or Evergreen/Plastruct tube the same diameter. Cut the drive shaft in 2 near the center, and splice in the tube. Or just lengthen the pins on both ends.
Jantrix Posted August 20, 2012 Posted August 20, 2012 I just picked this up on a trade and I'm unfamiliar with it. Whenever I see this kit on a store shelf, the box always features a stock build up so I was a bit surprised to see the gasser parts and an optional El Camino style top for it. As I don't see many build ups of this kit, so I figured I'd ask. Any quirks or problems with this kit I should know about before I start the planning process? Good, bad, ugly? Thanks.
Gluhead Posted August 20, 2012 Posted August 20, 2012 It's a real old tool but as you can see it's a notch above the typical amt of that time. The body definitely benefits from a good block sanding. If you're careful about test fitting and take the time to do all the cleanup necessary, it can build up pretty nice out of the box. I've never built one up with the gasser parts...they seem a little on the hokey side to me, but would probably be okay if you went the extra mile on them. I know I've used some of the parts to kitbash other gasser chassis together. I've never been a fan of the el camino roof but some have pulled it off alright, if you're into that.
ChromeIt Posted August 20, 2012 Posted August 20, 2012 I am currently working on one of these - mine is the "Johhny Lightening" version which has a small die-cast hot-wheels style version included in the box so I'm not sure if it is exactly the same as yours, but I think it is since it also includes the "El Camino" roof part and gasser front end as you mentioned. I haven't started actually building it, it's still in the painting stage so I can't tell you too much yet. But I did discover that the back for the rear seat seems to be missing in my kit. Other than that, in my test-fitting of the various parts, all seems well with mine.
Casey Posted August 21, 2012 Posted August 21, 2012 (edited) *dead link deleted* Edited January 13, 2018 by Casey
Monty Posted August 21, 2012 Posted August 21, 2012 It's an old tool, but it has several features that I thought were neat touches: poseable steering, front height adjustable via kingpin placement, & IIRC, the tailgate swings down. I normally don't even bother with the "custom" body pieces on most old AMT kits because I think they're garish, but the custom grille on this is subtle yet effective. OTOH, the engine looks slightly small (don't know if it actually is or not) and the chassis has a single, molded-in exhaust. If you're building the drag racer or a serious street car, you'll want to find a way to carefully remove that.
kobuzz Posted August 21, 2012 Posted August 21, 2012 Here is one of my projects using that kit. Building the gasser version.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now