BMW 507 Cabrio 1957 - Elvis Presley's one - Revell old kit 1:24

[CrazyCrank]

Evening gentlemen 

Well, the shaping of passenger's door is finished .

The last layer of putty has been sanded and the door is now ready for priming... which for sure could  reveal some imperfections that I'll have to fix !

   

 

I've again improved a bit  the inside panels of the doors:

- They have two door pockets that you can open while pulling a leather strip.

- On the kit, these "handles" are represented, but there's a lack of realism, because the strips are tightly fitted against the panel.

- To give them more relief and realism, I've cut with a 0.15 mm Tamiya PE saw the bottom part of the strips, and lightly and carefully bend them towards the inside of the tub

   

 

The driver's door has furthermore undergone the same modifications as the passenger's one.

Its 2 panels have been cemented together with Epoxy putty, and this  must dry at least 24 hours before I can fill the gaps between them.

 

In the meantime, I think I should have a go on the hood and the mechanism which retain it when it's opened...

The 2 doors fit perfectly and close smoothly, as I planned and hoped it would be 😎

 

 

And now, some shots of the whole bodywork at its current state:

   

 

 

Stay connected if you like, guys and thanks for watching 

 

 

Edited October 8, 2022 by CrazyCrank

[CrazyCrank]

Evening chaps 

Well, I do think that the preliminary work on the bodywork is at last finished this evening:

The doors have been adjusted and fits quite perfectly with the body. They open and close smoothly and all the gaps have been filled as much and well as I could.
The fuel trap opens correctly , as well has the trunk lid.

It remained for me, in order to be totally happy, to articulate the bonnet as it is on the true car.
- I haven't modified the system Revell supplied, even if it is not the reflect of the reality, because that would have been possible but very risky to do it.
- nevertheless, I've enhanced it, because with the Revell system, the bonnet wasn't correctly retained on the body and often detached from it.
- But the best I've done is to add the opening and retaining linkage that exist on the real car !
 

Let's see what it looks like on different photos :

   

 

So, it consists in 2 parts. The lower one is  a slide rail; in which can slide the upper part.

The 2 parts are articulated:

- the lower one with the bodywork

- the upper one with the  bonnet

Revell's kit supplies a part which could be a slide rail, but which is planned to be attached on the body AND on the bonnet, so tat no movement is possible.

It is supplied to be used to represent the car with bonnet opened !

I've used this plastic part that I've cut, removing its upper part (about 5 mm)
And I've closed the rail, glueing on it a piece of clear 0.18 mm sheet.
At last, the upper part of the system has been fabricated using a  1.0 mm wide (0.2 mm thick) Nickel-Silver strip, that I drilled 0.6 mm on its upper end. The hole allow a 0.5 mm steel wire that I've fixed on the bonnet frame with CA glue, to thread into it.

I've modified the fixing point of the Revell kit part (the plastic rail) on the body, cutting the plastic pin, and drilling a 0.7 mm hole into the stand in order to be able to thread into it a sewing needle

 

And all this work gives that:

   

 

Short videos to show you how it works :

 

Hope you enjoy  

See you soon with the first primer layer on all bodywork parts 😎

[afx]

Great work Thierry on hinging/articulation of the panels.

[CrazyCrank]

11 minutes ago, afx said:

Great work Thierry on hinging/articulation of the panels.

Many thanks, @afx 😎

[CrazyCrank]

Morning gentlemen 

You could believe you've finished the preliminary job on the body, but it remains always an something to do you had forgotten !

Indeed, in my "haste", I forgot to modify the air intake grill that is just in front of the windscreen, and its housing on the body, which is not hollowed out !
So, I did this job this morning.
I've removed the 3 parts of the grill that are supposed to represent mesh, keeping only the chromed frame.
I've also thinned the part, sanding it from below, because it was too protruding from the body once in place.
The meshed parts will be added later with some spare mesh from my Tamiya Mercedes 300SL or Revell 300SLR,,,,I've not yet decided.
I've hollowed out the grill housing on the bodywork.

The kit's grill, before and after the job:

   

The chrome will be removed with bleach, an he grill carefully sanded in order to decrease the thickness of the frame before painting.

The grill housing on the body, before and after the job

 

   

The new grill in place on the modified body:

You have just to imagine how it will look like with mesh by underneath 

 

See you later 😎

 

[Oldcarfan27]

Fun thread. Thierry, you've got great detailing skills!

I like the retracting hood support. 

[CrazyCrank]

1 hour ago, Oldcarfan27 said:

Fun thread. Thierry, you've got great detailing skills!

I like the retracting hood support. 

Thanks for this compliment.

And  regarding the hood support: "#metoo"

 

[CrazyCrank]

Evening gentlemen 

I began last week to work on the engine.

It's a nightmare !  the fitting of engine's block parts is problematic, there' s a lot of burrs on them, abysmal gaps between parts etc...
So a lot of filing, sanding, filling etc was needed.
But it was worth the efforts !

On the top part of the engine block, between the cylinder heads, Revell has molded two looms ("flute " ?, I want to mean "cable distributor/channeler") that are used on the real car, to channeling the spark plugs cables.
Obviously, on this kit, no spark plug cables are supplied ! you have to scratch them for yourself if you want to represent them...of course, it's my case !
So, I've removed the molded looms  , that will be replaced by 1.0 mm aluminium tubes, slightly flattened and drilled where needed. 
Those new looms will allow to represent correctly the ignition system.
Therefore, I had to drill on the cylinder heads 8 holes for the 8 sparks plugs of this V8 engine.

What I made easily, taking inspiration of these photographs for placing the holes :

The second photo has been taken by the mechanics who restored Elvis' BMW 507

The actual state of my engine after this job and painting:

   

 

 

Then I've added to the engine block:

- the rock-arms covers (painted steel and polished)

- the gearbox, which has needed a lot of sanding and gap fillings

- I've painted the oil pan the same color of rock-arms covers: steel.

- I've fabricated the oil gauge housing and its dipstick, that were not provided in the kit

 

I took inspiration of this photo:

 

Making of:

- drill a hole in the oil pan with  0.8 mm bit, at an angle of about 30° relatively to the vertical, from top towards bottom

- drill two 0.8mm holes in a plastic rectangular parallelepiped of 2.5x2x1.5

- Insert in the holes 2 sections of 0.8 mm aluminium tube.The front one will simulate the oil drainer and is vertical, the rear one is slightly bended at its bottom end, which will be inserted in the oil pan hole

- Make the dipstick with 0.18 mm nickel-chrome wire, bended to get the correct shape. And a short section of 0.5 mm brass tube has been cut out and the dipstick threaded into it...

- The hole set as been assembled, glued together, primed, painted semi-gloss black, except for the dipstick that has been painted red,  and the while set has been clear coated semi-gloss as well.

 

Some photos of the process:

   

 

   

   

 

It remains to paint rubber black the oil drainer, and I could next go on with the looms and the cabled spark plugs.

Stay tuned for next steps 

 

[noname]

This is fun to watch. Love the reality you are building into this miniature car. Inspiring!

[JohnB]

Huge Elvis fan here, can't wait to see the finished project. Awesome work

[slusher]

I been watching impressive work!

[CrazyCrank]

Morning chaps

 

A lot of progress since my last post!...but I will only post a small part of it today, so as not to bore you!

I've fabricated 8 spark-plugs and their cables.

I used:

- black electrical micro wire 0.27 mm diameter, 6 medium sections and 2 large

- 8 sections of 0.5 mm brass tube, 4 mm long each

- 8 sections of 0.8 mm aluminium tube, 0.5 mm long each

- The alu parts have been threaded on the brass ones, placed  a little before the centre

- the black wires have been threaded at one end of the brass tubes

- the brass tube above the alu section and this last one have been painted red (a mi 50/50 of gloss and flat reds)

- the brass tube under the alu section has been painted white, to simulate the ceramic part of a spark plug

A last this 8 elements have been placed into the 8 holes of the engine block

 

   

 

   

The looms have been fabricated with 1 mm aluminium tube, 2 sections of 12 mms, in which of each one I've drilled 3 holes.

Why only 3 holes and not 4, since there's 4 cylinder on each sides ?

Because the front spark plugs cables doesn't go through the looms, they come directly from the distributor !

The looms have been glued in place with 3 droplets of fluid CA.

 

 

At last, the 3 rear spark plug  cables of both sides of the engine have been cut to the right length and the cables inserted in the holes of the looms

 

 

   

 

   

 

 

The  alternator supplied in the Revell kit (BMW 507 series 1 ) seems to be a series 2 one ! , but, when Elvis's BMW has been restored, they have used a different distributor, on which the cables are plugged on the top of it.

 

 

So, I can't use the kit part, and I've designed a good one with Fusion 360

 

 

 

I took the opportunity to design as well a coil, because this visible part when the bonnet's opened, has not been supplied by Revell !!!

 

   

 

But that's not all. I also began to work on the other kit parts of the engine.

It took 2 hours to clean them and make them acceptable, particularly the pulleys and bel systems.

But I've had to modify others because they were not accurate or incomplete .

That was the case for the exhaust manifolds and for the alternator.

 

The exhaust manifolds supplied by Revell have the right shapes BUT on the real ones, there is 3 fins on each one, which, imho, are there to reduce the heating, offering additional surfaces for air cooling when the car runs

 

I intended to reproduce them adding tiny strips of 0.18 mm styrene 

   

 

   

 

The distributor is molded with another part of the engine, and is very basic. Its pulley is inaccurate, there's not the cooling propeller, so I added it, from scratch with 0.18 mm styrene sheet, magnifying glasses and a lot of patience

   

 

 

That's it !

What !!! that's all ?....well yes , at the moment 😉

Edited November 7, 2022 by CrazyCrank

[CrazyCrank]

Afternoon guys 

Busy last week to fabricating the second  end of the 8 spark - plug cables and the cable which goes from coil to distributor
6 spark-plug cables come out of the distributor to join the looms
2 other spark-plg cables, the front ones, are already connected to the engine block by the spark-plug and have the other end free, theses ends will connect directly on the distributor top va connectors
The coil cable is free at one end, which be inserted in the coil, and the other end connects on the distributor via a connector.

So, I fabricated 7 connectors with their cable and 2 connectors without anyone.

What did  I use for that ?:

- A short section of 0.8 mm aluminium tube (0.6 mm,inner diameter) , about 1 mm, drilled on the center, perpendicularly, 0.6 mm

- A short section, about 1.5 mm of 0.5 mm brass tube, 0.3 mm inner diameter

- A section of 0.25 mm black electrical wire

- A section of 0.4 mm steel wire

- UV transparent resin.

- Fluid CA glue-

- Insert the 0.4 mm steel wire in the 0.6 hole of the 0.8 alu tube....glue

- Put a droplet of UV resin at the opposite side of the alu tube, near the brass tube... UV cure

 

In total, the wiring of distributor, coil and spark plugs required:

- 2 alu looms (flutes)

- 1 3D printed coil

- 1 new 3D printed  distributor

- 15 sections of black 0.25 electrical wire

- 8 0.5 mm sections of 0.8 mm alu tube

- 8 sections of 2 mm of 0.5 mm brass tube

- 9 sections of 1.5 mm of 0.5 mm brass tube

- 9 sections of 1mm of 0.8 alu tube

- 9 sections of 0.4 mm steel wire

- 3 drill bits 0.3 mm and 1 0.5 broken

So 62 tiny parts to assemble together !!! and probably a dozen of hours !!...not to mention that it remains to paint the connectors (rubber black)

Pictures:

   

 

   

 

   

 

   

 

I made some progress on the engine, glueing the starter motor on the block, painting and assembling the pulleys and alternator, and the exhaust manifolds.

 

   

 

I also painted the distributor, brick red for the top and semi-gloss black for the bottom.
I've re-drilled the 9 holes on its top with 0.6 mm drill bit, to allow an easy fitting of the connectors's pins.

AND THEN, I made a test, trying to insert on it the 9 connectors I fabricated previously, and also to order up the cables to make them come out to the rear and about the same direction.....

NOT GOOD.... NOT GOOD AT ALL !

 

Why ?
- There's no room enough to place correctly the connectors, whose horizontal portion is a bit too long
- Despite I worked carefully and thoroughly , the connectors have not EXACTLY the same size, and the final aspect is not aesthetic.
- At last, some connectors are a bit too tall and I fear that the bonnet couldn't close entirely.

So, I tried a new approach !
- I created a new design for the distributor, placing correctly on its top 9 connectors (same shape, same size, same height), whose horizontal portions were pre-drilled at 0.4 mm.
- I printed it and looked  how this turned out:
The draft looked good, and the most back connectors had a good drill, but the centre one and the most frontal ones hadn't. It was the case for the 6 distributors I printed simultaneously.
SO, NOT GOOD...But encouraging !

And my last and absolutely presumptuous and crazy attempt is the following:
- I designed a third distributor, with better shaped, more accurate and resembling to the true one.
- I placed on its top 9 pins 0.4 mm diameter,  0.5 mm tall.
- I designed also the connectors, vertical portion 0.9 mm tall, 0.9 mm diameter, pre-drilled at 0.6 mm, and horizontal portion 0.6 mm long, 0.5 mm outer diameter and 0.4 inner one....(I bought a microscope to see them after 3D printing)
- I printed 6 distributors, to get spare parts, and 36 connectors (4 times more than what I need, because several ones could be badly printed, and of course, taking in account their small size, it was sure that I would loose some ones)

 

And then ? and then ???... Zorro arrived ?....NO! but a kind of miracle occurred !
- The distributors look good.
- The lilliputian  connectors look good, 16 failed to be printed correctly, the holes of the vertical portion are neat and match the design, the 0,4 mm pre-drilled holes of the horizontal portions need to be unclogged.
- I did that for 13 connectors (7 lost) and manage to insert and glue  in 9 of them the 0.25 mm electrical wire, but it took me 2 hours under magnifying glass !

   

 

 

   

 

   

 

 

Little comparison between the first metallic connectors, on the top of the following photo, and the new ones, on the bottom:

 

 

I've also modified the design of the ignition coil, because I noticed, lately, that it it fixed upon a vertical stand, and not directly on the engine block

   

 

   

 

A last, I've also sprayed the final coat of fine Gravity Colors light primer on the body and the chassis.

I'll show you photos taken in day light later, because the day is now fading

 

Stay tuned and thanks for watching 😉

[absmiami]

Whats French for Determined ?

[CrazyCrank]

1 hour ago, absmiami said:

Whats French for Determined ?

"Déterminé"...as simple as this !

[absmiami]

I figured it started with a d ….

[Rocking Rodney Rat]

That's some amazing work going on! I love the hinges. -RRR

[CrazyCrank]

Good evening guys 

Still working on the engine, I go on now with the fuel lines, pump, filter and carburetors (with their air filters)

Since my previous post,  I've managed to enhance an engine part, which is badly represented in the kit:  the fuel pump (or filter ?)

The true one:

   

 

The kit part: dimensions 5 x4,4 mm

   

 

My interpretation:

   

 

The firsts 3D fuel pump came out nicely, but they are draft ones and the accuracy, for so tiny parts, can be improved by 3 printing them at 10 microns layers.

 

So, a second print was started....4 hours to wait !

In the meantime, I continued to study all the ref. photos, and I noticed that there is, on the top of the engine block, 2 motor lifting rings.

I've intended to reproduced them and to place them on the right locations, one on the front right, and the second on the rear left, taking inspiration of the photo below (Elvis 's BMW 507 restoration):

 

 

For this purpose, I used:

- 0.2 mm steel wire

- A sewing pin of 0.6 mm

2 times, I made a buckle, rolling up the wire around the needle, and I cut it delicately.

And I got 2 stuffs I introduced into 2 holes drilled at the right locations on the engine block

Then I painted them black, and...that's it !

   

 

   

 

The second print at 10 microns layers of the fuel pump came out very nicely..It was worth the 4 hours waiting !

The photo above does not justice to this part, which is in reality, even at the naked eye, very neat and accurate !

I've also designed a new carburetor, taking inspiration of a new and great picture I found by coincidence !

 

Of course, my design isn't true. It's an interpretation, given the fact that I haven't any blueprint, and only 2 or 3 photos taken at almost the same angle.

But it's still far better than the stuff supplied in the kit: a disk over a cube !

 

 

 

 

 

 

 

 

I've separated the carb and the disk-shaped air-filter, in order to be able, later on, to fabricate and install  more easily the fuel lines and the throttle linkage i

 

 

I'm currently printing a draft of these two parts at 25 microns layers, what will take 2 hours.

If the test fit is OK, I'll print them at 10 microns.

See you later, guys 

 

 

[CrazyCrank]

Morning   gentlemen 

I've completed the fabrication  of the air filters.

You remember  that they have a disk shape, 8.5 mm diameter for my replicas , and are on the real thing made of two plates, on top and bottom, which trap in between, the air filter itself.

And the peripheral of the "disk" is made of a perforated grid.

 

When I designed my air filters for 3D printing them, I've anticipated the fact I need to have a groove between the 2 plates, in order to place the perforated grid more easily (the groove acting as a rail to guide the grid strip)

I trained this evening with a spare air filter, not painted.

Theoretic Process:

- Cut off a strip of fine mesh, just the right height, the groove one in fact, 1.0 mm, and the right length, so for a 8.5 mm diameter disk, a length of  Pi x 8.5, so 26.7 mm

- Glue it with very small amounts of superfluide CA ( I used Loctite 420) around the "air filter", in the groove.

Making off :

- I had so, first, to cut of a rough rectangle of mesh from my big roll, and, without any willing and by pure chance, I was extremely lucky because my rectangle was exactly 27.0 mm wide !

- Then, to  get a regular strip of 1 mm width, I stuck long the edge of my mesh rectangle a strip of Tamiya masking tape 1.0 mm, as if I want to mask before painting.

- Then, I stuck  a large strip of masking tape along the first strip, the edges in "full contact".

- At last, I removed the fine strip and I cut off a 1.00 mm strip of mesh, with sharp scissors, following the edge of the remaining strip.

The final step was to glue the mesh strip in the groove, little by little, avoiding overflowing the glue outside the groove.

 

And I succeeded  

 

After that, it remained to repeat the process with two painted air filters, only a matter of time and patience !

   

 

   

 

   

 

   

 

 

And....that's it 

I think they look really very similar and I'm pretty happy with the result .

 

Next , I stuck the fuel pump (filter ?) in place, and the distributor as well.

 

   

 

And I began to work on the fuel lines of the carburetors, a challenging work at this scale.

I took inspiration of this photo (and many similar others)

 

I used:
- 0.25 mm Nickel-Chrome wire to represent the fuel lines
- some outer 0.5 / inner 0.3 mm diameters brass tube
- 1 drill bit 0.3 mm
- Soldering paste
- And Superfluide CA glue (Loctite 420)
- Short sections (2.5 mm) of thin Electrical black wire (0.5 mm diameter)

 

Process:
- cut off a short section of brass tube, about 0,75 mm (part 1)
- Thread it over an about 20 mm section of  0.25 NiCr wire ( part 2)
- Drill a 0,3 mm hole perpendicularly on a 2 mm section of brass tube (part 3)
- Thread in this hole the NiCr wire (part 2) and let the short section of brass tube which is threaded on it (part 1), slip until it touch the drilled brass tube (part 3)
- Solder
- Cut the excess NiCr wire which overcome of the drilled brass tube (part 3), sand and polish .
- You have now a brass "T", in which is threaded  1 long section of NiCr wire
- Unclog the holes of the drilled brass tube (part 3)
- Glue with superfluid CA 2 long sections of NiCr wire in the holes(Parts 4 and 5)
- You have now  a brass T with 3 branches of NiCr wire
- Cut 2 short sections of 0.5 mm black electrical wire, remove the cable core
- Thread them over the 2 horizontal branches of the T (parts 4 and 5)

 

   

 

And that's it !

It remains, obviously, to shape the NiCr wires correctly and to fix the piece you'll get between the fuel pump and the 2 carburetors.

 

 

And 10 days ago, I  finished to fix on the engine block the carburetors and their fuel supply !

It was no picnic !

I also simulated the throttle linkage of the carbs with small pieces of 0.2 mm NiCr wire,  shaped little by little.

   

 

   

 

   

 

   

 

On the pictures below, the air filters are not glued on the carbs, just put on, to get an idea of the final result.

They will be glued in place only when the engine is fixed on the chassis.

 

   

 

 

It seems to be coming to life, doesn't it ? 

Stay connected for next steps 😉

 

[absmiami]

Yes it is !

[Pierre Rivard]

Travail magnifique Thierry,

Always inspirational and a bit intimidating looking at your craftsmanship.

I just spent hours reviewing your Moss SLR w.i.p. on BritM because I want to learn before I tackle mine (thinking to do a Fangio conversion). If I can achieve 10% of your detailing magic I will be very happy!

Thank you for sharing your work.

[CrazyCrank]

On 11/27/2022 at 4:02 PM, Pierre Rivard said:

Travail magnifique Thierry,

Always inspirational and a bit intimidating looking at your craftsmanship.

I just spent hours reviewing your Moss SLR w.i.p. on BritM because I want to learn before I tackle mine (thinking to do a Fangio conversion). If I can achieve 10% of your detailing magic I will be very happy!

Thank you for sharing your work.

Merci Pierre

Thanks a lot 😎

[CrazyCrank]

Morning guys

 

As promised, here is the result of my  painting job for Elvis BMW 507's bodywork  

I do think the final color is very close to the original white pearl it arbors since its restoration , the same color as it had when Elvis bought  it.

I've been very surprised when I placed side by side my damaged and unpainted plastic body and the painted one, because in day light, the colors are very similar

 

 

It remains now to give it some layers of gloss clear coat.

This will be done in a few days.

And then, the assembly will be able to go ahead 

[adamelvis]

WoW, WoW, WoW !!!

TCB,

Adam

[CrazyCrank]

Morning gentlemen 

A lot of work on this since my last post.

The chassis has been clear-coated, semi-gloss on the whole  underbody but the trunk, and gloss on the inner and outer sides of the wheel arches and the underside of the trunk.

   

 

   

 

Don't take in account the molding marks in front of the radiator and on the top of wheel arche"s...they will be hidden once the assembly is done !

I began to paint and assemble the exhaust lines, and the rear axle.

A little bit of weathering remains to do on these.

   

The transmission shaft has been painted (gloss black) and is temporarily put in place, waiting to be glued on the rear of the gear box, at its front end, and to the differential housing at its rear end.

About the rear axle, it remains to to add the shock absorbers, but those supplied in the kit are ....how could I say it ?.... awful !

 

So I decided to scratch them:

- A 3D designed and printed part for the upper part

- And  a true metal stuff for the lower: I haven't decided yet whether it will be a nickel-plated brass rod, or a polished and varnished aluminium one. I"ve to sleep on it !

 

The horns supplied in the kit, that have to be glued on the front of the radiator, are very bad pieces of ugly plastic, twisted and unrealistic, so;, I designed them as well !

The kit part:

   

 

My 3D one:

 

At least, the radiator has been modified, by the addition of a very thin piece of mesh on both sides

 

A little bit of progress  with the completion of the rear axle.

Finally, for the shock absorber's pistons, that must look like polished steel, I decided to scratch them with a rod of brass, that I nickel-plated, and they look great, even if their is a bit low (1.0 mm instead of 1.3 on the kit part)

The upper resin part has been painted red and gloss clear coated.

   

   

 

The horns have been primed and painted semi-gloss black, and are now glued in place in front of the radiator .

 

The front shock absorbers are those of the kit, but have been enhanced with some painting:

 

I used a very nice chrome (Gravity Color Mac Laren chrome set), sealed with Alclad Aqua gloss

Front axle assembly achieved, not without a lot of difficulties, since the instructions are very poor, and the drawings not explicit.

But it's done, and it works

 

   

 

   

 

  

 

It remains to give the front axle a little bit of weathering, because the restored car has already be driven on several roads, and I'll use some road dust pigment and polished metal pigment to highlight the reliefs of the axle components.

Of course, it will be done at the very end of the  build.

The chrome exhaust tips still need to be made.
The parts supplied in the kit are of poor quality, incorrect size and are solid, whereas tube is required.
They will therefore be turned on the the lathe in brass rod, then nickel plated.

 

The engine has been placed and glued in the chassis, and of course connected to the transmission shaft.

 

   

   

Don't pay attention to the dust and stains on the bodywork at wheel arches level, I know I've to tidy up the engine bay !

I've tried to make a test fit with the radiator and it appeared that it's not possible to position it vertically for two reasons:
- one: the fan is too protruding and hit the rear side of the radiator
- two: the lower edges of the radiator hit the wheel arches, what prevent it as well to set vertical

So, I've had to make a delicate surgery:
- cut off the fan, and decrease the thickness of its hub, on the rear, from about 1 mm
- trim out the lower edges of the radiator

And now, all's OK, or so (on the photo below, the radiator bend slightly forward because it's not glued and the weight of the horns is unbalancing it)

However, the radiator won't be glued immediately, because my hands need room to place easily my tiny spark plugs and their wiring !

I've spent no less than 5 hours to place correctly the ignition wiring !

Not less than 8 spark plugs connected on the distributor, plus the ignition coil plug !

A lilliputian work under magnifying glass, with several pauses in order to calm my tremor !

But it was worth the efforts !

During the process:

   

   

   

   

Once achieved:

Once painted:

   

   

 

A total of 42 parts were assembled for the ignition system !

She's coming to life !

 

I've spent a few hours today to prepare, paint, and improve a single part: the water cooling upper duct.

It consist in 2 rubber hoses separated by a roughly spherical piece, connected, on the front to the radiator, and on the rear to the engine block
The whole part was too large to fit correctly between the engine and the radiator, and I've had to make some surgery.
The rubber sections have been painted rubber black, and the middle part semi-gloss black.
As on the true car, I've added fastening collars, 2 on each rubber section, made from very thin strips of Hasegawa Mirror Finish (about 0.5 mm wide).
Not an easy job on a painted tiny part.
I'm not absolutely happy with the result, but you know that I'm too much perfectionist. 

I've as well decided to modify the carburetors fuel supply lines, because the angles of the lines were too sharp, and I wanted them rounded.

A delicate and tedious job, but it was worth the pain.

 

At last, I've glued in place the air filters

   

   

 

Don't think the job is over!

There are still a lot of things to install in the engine bay and under the bonnet:
- first of all, the expansion tank and its hoses
- but also the fuel inlet pipe and its connection to the filter
- the steering,g mechanism 
- and several pipes, once the firewall, currently attached to the body, will be in place ... and this is not for tomorrow!
- and all the rest, which I will spare you the enumeration

I leave France on Thursday and don't know what I'll be able to make on this model during the 2 next days, but stay tuned, if you like