RocketFoot Posted September 29, 2023 Share Posted September 29, 2023 My Mach 1 has traction bars on the rear axle so naturally, I want to add them to the replicas I am building!ย Question is, should I just glue them on the bottom of the leaf springs or should I go all out and use thin wire to mimic u-bolts?ย I am curious to see some photos from you guys, if you don't mind sharing!ย I looked at a lot of Under the Glass threads but I haven't noticed 1 set of slapper bars yet! Here is my actual 1:1 Here is the resin parts I am looking at for the builds... An and all advice is greatly appreciated!! ๐ Quote Link to comment Share on other sites More sharing options...
espo Posted September 29, 2023 Share Posted September 29, 2023 Since you have these on your car and you're building a replica of your Mustang then you should add them. Sounds like you are familiar with how they are installed, and I would just replicate that to the best of your ability. Don't know if going full "U" bolt replica is needed unless you feel comfortable doing that. At the very least just glue them to the rear spring mounting pad. I think there are a set in the Revell '69 Nova SS kit. There may be others also. Looking at your picture these could be made out of some scrap spruce. I'm sure others will chime in withย some other suggestions.ย ย Quote Link to comment Share on other sites More sharing options...
RocketFoot Posted September 29, 2023 Author Share Posted September 29, 2023 6 minutes ago, espo said: Since you have these on your car and you're building a replica of your Mustang then you should add them. Sounds like you are familiar with how they are installed, and I would just replicate that to the best of your ability. Don't know if going full "U" bolt replica is needed unless you feel comfortable doing that. At the very least just glue them to the rear spring mounting pad. I think there are a set in the Revell '69 Nova SS kit. There may be others also. Looking at your picture these could be made out of some scrap spruce. I'm sure others will chime in withย some other suggestions.ย ย Thanks!ย Yes, I am just looking for some ideas and inspiration! Quote Link to comment Share on other sites More sharing options...
Z28 Posted September 29, 2023 Share Posted September 29, 2023 Yep, for sure. Like you Iโm building a replica of my Z28 in 1/12 scale. Hereโs the pictures of what I came up with.ย 4 Quote Link to comment Share on other sites More sharing options...
RocketFoot Posted September 29, 2023 Author Share Posted September 29, 2023 14 minutes ago, Z28 said: Yep, for sure. Like you Iโm building a replica of my Z28 in 1/12 scale. Hereโs the pictures of what I came up with.ย Nice!ย Those look really good!ย 1 Quote Link to comment Share on other sites More sharing options...
Z28 Posted September 29, 2023 Share Posted September 29, 2023 27 minutes ago, RocketFoot said: Nice!ย Those look really good!ย Thank you. Not too terribly amount of hours building those in one 1/12 scale. I would imagine in 1/24 scale, it would be a lot different. Quote Link to comment Share on other sites More sharing options...
bobss396 Posted September 30, 2023 Share Posted September 30, 2023 I have elcheapo Summit bars on my old Ford, yellow of course. They work well and most of my wheel hop on the 1-2 shift is gone. I saw the resin ones too and they look good. Make some u-bolts from .020" brass rod, or aluminum rod that Detail Master carries. And their #1 hex nuts and it will look real. Quote Link to comment Share on other sites More sharing options...
GLMFAA1 Posted September 30, 2023 Share Posted September 30, 2023 On YouTube,HPGuy does the 1969 'Cuda' build and the tree has some traction bars. (2:06) greg 1 Quote Link to comment Share on other sites More sharing options...
NOBLNG Posted September 30, 2023 Share Posted September 30, 2023 17 hours ago, RocketFoot said: My Mach 1 has traction bars on the rear axle so naturally, I want to add them to the replicas I am building!ย Question is, should I just glue them on the bottom of the leaf springs or should I go all out and use thin wire to mimic u-bolts?ย I am curious to see some photos from you guys, if you don't mind sharing!ย I looked at a lot of Under the Glass threads but I haven't noticed 1 set of slapper bars yet! Here is the resin parts I am looking at for the builds... ย An and all advice is greatly appreciated!! ๐ Since itโs a replica of your own vehicle, I think you would be happier with wire u-bolts. Beading wire in ย 0.015โ (or close) would be 3/8โ in 1/25 scale. The bars themselves would be quite easy to fab from a bit of evergreen rectangle and sheet stock. JMO.๐ 1 Quote Link to comment Share on other sites More sharing options...
RocketFoot Posted September 30, 2023 Author Share Posted September 30, 2023 I'm definitely going down the rabbit hole of extreme model detail!ย At least the AMT build is my practice run...the Revell kit will be no holds barred! Quote Link to comment Share on other sites More sharing options...
Can-Con Posted September 30, 2023 Share Posted September 30, 2023 There's also a set of those in the MPC Dodge Dart Sport kits. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.