2023 Cannonball Run-What-You-Brung Build Thread

[White Rabbit]

Great updates everyone! The builds are looking fantastic!

[Spottedlaurel]

Good see to see the updates.

Haven't had a lot of time to anything on mine recently, but I polished it a while back. Wasn't entirely happy with that, so I gave it a T-Cut and second resin polish today.

Also made some modest progress with interior:

Cut out and glued in some pieces of wet-and-dray paper for the carpeted areas. Aftermarket resin seats are primed along with everything else, so I can start getting some colour down (well, shades of black and grey).

[Spottedlaurel]

Spurred on by what I managed yesterday I got a reasonable bit more done today:

Brake calipers and wheel centres given a coat of gold (may do a second coat on the latter), matt and semi-gloss black daubed on various parts of the interior, and painted the headling and inside of the bodyshell.

Had a Revell Shelby Series 1 come the other day, it has staggered tyres which might suit the mid-engined layout here.

Got a bit of leave later this week, will try and find time to move it on a little bit between the outside jobs on the house/garden I'm meant to be doing.

[White Rabbit]

Hello everyone! As we are nearing the end of this year's Cannonball, I just wanted to post the important dates below. Please remember, that to be part of final voting, the finished builds must appear in the Finished Build Thread.

Important Dates: 2023

January 1st, 12:00am: Official build start of the 2023 Cannonball Run

November 14th, 12:00am: Finished build thread opens

November 29th, 11:59pm: Last day to enter the CBR build

December 1st, 11:59pm: Official build end

December 3rd, 12:00am: Polling to elect a winner opens

December 16th, 11.59pm: Polling closes

December 17th: 2023 Winner announced

[vekasiini]

Dodge L-xxx

 

Dodge advances after the break.

[Beans]

2 hours ago, vekasiini said:

Dodge L-xxx

 

Dodge advances after the break.

Nice to see somebody else using the advanced clamping system of whatever is heavy and on the bench.  

[KWT]

2 hours ago, Beans said:

Nice to see somebody else using the advanced clamping system of whatever is heavy and on the bench.  

I do it quite often myself

[MeatMan]

Sorry for the lack of updates but I haven't had much bench time.

I had painted my 918 back in September but used liquid mask on some of the harder places to mask with tape and it was a headache to remove.

This was the hardest model to paint that I've ever done. Lots of nooks & crannies that needed to be black.

In the end it turned out pretty well. The color is beautiful and if I had worked more on smoothing the color before clearing it would be a perfect paint job.

Now to put it all together.

[disconovaman]

Second attempt at paint work... I messed up the stripes, I wasn't happy with the results so I decided to start over and it's another color. This is more like it... the other color was kinda flashy compared to this one. I definitely know how to complicate a project, this was supposed to be a quick build. 🙄

[Spottedlaurel]

10 hours ago, disconovaman said:

Second attempt at paint work...

Looks great, good luck with getting it to the finish line.

Same for everyone taking part, not long now....

 

Dabbled with my CBR project yesterday, will try and do a little bit more today. Main job left is detailing the body, with lots of panel line washing and trim painting which aren't my favourite jobs. Interior largely done, need to think about a rollcage.

[disconovaman]

Back to where I left off is good spot to be in so I think I can finish strong now... I used to build in a day when I was young... how did we do that? Now it's a struggle to get something built in a year... 😆 

[Keef]

19 hours ago, disconovaman said:

Back to where I left off is good spot to be in so I think I can finish strong now... I used to build in a day when I was young... how did we do that? Now it's a struggle to get something built in a year... 😆 

About 25 years ago I built 14 kits in a 24 hour period. 5 large pots of coffee and a family sized bag of pizza rolls were involved. 😂🤣

[slusher]

On 11/5/2023 at 10:25 PM, disconovaman said:

Back to where I left off is good spot to be in so I think I can finish strong now... I used to build in a day when I was young... how did we do that? Now it's a struggle to get something built in a year... 😆 

Looks sweet!

Edited November 8, 2023 by slusher
Typo

[slusher]

On 11/3/2023 at 8:03 PM, MeatMan said:

Sorry for the lack of updates but I haven't had much bench time.

I had painted my 918 back in September but used liquid mask on some of the harder places to mask with tape and it was a headache to remove.

This was the hardest model to paint that I've ever done. Lots of nooks & crannies that needed to be black.

In the end it turned out pretty well. The color is beautiful and if I had worked more on smoothing the color before clearing it would be a perfect paint job.

Now to put it all together.

Beautiful paint and color!

[MeatMan]

On 11/7/2023 at 11:09 PM, slusher said:

Beautiful paint and color!

Thanks Carl.

[Whosurdaddy209]

I had to make a tough decision about my engine, after getting everything put together I wasn’t very happy with how it looked, so I decided to scrap the original engine and start over with a supercharged LS9 from a donor ZR1 kit. I am much happier with it now. The only thing left on this one is to clear and polish the hood, then do a final polish on the whole car and I can call it done😁

[SpikeSchumacher]

Sweet!

[MeatMan]

5 hours ago, Whosurdaddy209 said:

I had to make a tough decision about my engine, after getting everything put together I wasn’t very happy with how it looked, so I decided to scrap the original engine and start over with a supercharged LS9 from a donor ZR1 kit. I am much happier with it now. The only thing left on this one is to clear and polish the hood, then do a final polish on the whole car and I can call it done😁

Perfect fit! Nice detail as well.

[MeatMan]

I painted the wheels I printed for my 918 and decided to do a quick mock-up, so I stuck on the front & rear fascia and put decided to check the windshield for fit.
Lo and behold, the curvature of the windshield doesn't match the curve of the frame. Dunno what I'll do to make it work. I think the the part I glued on the inside of the frame distorted it somewhat, as I've never heard of anyone else having this issue. Murph strikes again!

[Tim08]

All these builds are looking awesome. This is the last few months of updates. Got the racing green on it. and was still trying to figure out some wheels.

 

Finally settled on these

They were black so I painted them in a steel color, the black looked a little toyish to me. Here it sat a few months ago. Copied that cooler with allumilite resin, my first go at resin casting, did some steelies too. The roll cage didn't fit so I left it out.

 

Did some wiring on the firewall and inner fenders.

Here's how she sets right now, just got to finish up some painting, door handles and marker lights, that kind of stuff. Then put the rest of it together

Should be able to finish up before the end of the month.

[White Rabbit]

2016 AMG GT

My completed entry for this year’s Cannonball.

 

Overview

The idea for this year’s entry was to have a true GT car that, as Jeremy Clarkson once said, is capable of traversing long distances at a high rate of speed in complete comfort. Therefore, a GT car built for the Autobahn seemed like a good choice as it’s made to cruise comfortably at 150mph all day.

The car itself has some modifications, the most visible being the Vossen MX-2 wheels (20”F, 21”R) wrapped in Continental Extreme Contact tires. Both were modeled and printed. Furthermore, the rear wing was cutout and modeled and printed as well, with its respective brackets so that it could be posed in its open position.

The interior has Recaro sport seats with a 4-point roll bar just behind. The interior is fully flocked.

The exterior was painted in Tamiya Bright Gunmetal Semi-gloss, which is analogous to Mercedes’ Selenite Grey semi-gloss. The interior is sky grey and black with the roll bar in body color. Finally, for an accent, the wheels are titanium gold in front of black brake calipers.

The engine was built from the kit, but detailed with wiring and plumbing. The under-hood molded-in hoses were cutout and replaced with aftermarket hoses and wiring. The molded-in brake master cylinder/booster/reservoir and ABS pump were also removed. In their place is modeled and printed versions the have been wired and plumbed. The bracing that runs from the firewall to the fenders was also scratch-built and added.

 

Specifications

Kit: Revell 2016 AMG GT

Exterior Paint: Tamiya Bright Gunmetal, semi-gloss black

Aftermarket: HobbyDesign detail set (photo-etch and resin) and resin Recaro seats, various wires and hoses from Detail Master and Gofer racing, Evergreen and Plastruct plastic stock

3D Print: wheels and tires, brake master cylinder/booster/reservoir, ABS pump, third chassis brace, rear wing and brackets

Scratch-built: roll bar, pocket for brake master cylinder et al., oil filler and dipstick tubes, chassis braces (front), rear wing mechanism and body fill panel for the wing

Below is the completed model with the last picture of the AMG alongside last year's entry.

Thank you for looking and critiques are always welcome!

 

Edited November 12, 2023 by White Rabbit

[Fat Brian]

1 hour ago, White Rabbit said:

2016 AMG GT

My completed entry for this year’s Cannonball.

 

Overview

The idea for this year’s entry was to have a true GT car that, as Jeremy Clarkson once said, is capable of traversing long distances at a high rate of speed in complete comfort. Therefore, a GT car built for the Autobahn seemed like a good choice as it’s made to cruise comfortably at 150mph all day.

The car itself has some modifications, the most visible being the Vossen MX-2 wheels (20”F, 21”R) wrapped in Continental Extreme Contact tires. Both were modeled and printed. Furthermore, the rear wing was cutout and modeled and printed as well, with its respective brackets so that it could be posed in its open position.

The interior has Recaro sport seats with a 4-point roll bar just behind. The interior is fully flocked.

The exterior was painted in Tamiya Bright Gunmetal Semi-gloss, which is analogous to Mercedes’ Selenite Grey semi-gloss. The interior is sky grey and black with the roll bar in body color. Finally, for an accent, the wheels are titanium gold in front of black brake calipers.

The engine was built from the kit, but detailed with wiring and plumbing. The under-hood molded-in hoses were cutout and replaced with aftermarket hoses and wiring. The molded-in brake master cylinder/booster/reservoir and ABS pump were also removed. In their place is modeled and printed versions the have been wired and plumbed. The bracing that runs from the firewall to the fenders was also scratch-built and added.

 

Specifications

Kit: Revell 2016 AMG GT

Exterior Paint: Tamiya Bright Gunmetal, semi-gloss black

Aftermarket: HobbyDesign detail set (photo-etch and resin) and resin Recaro seats, various wires and hoses from Detail Master and Gofer racing, Evergreen and Plastruct plastic stock

3D Print: wheels and tires, brake master cylinder/booster/reservoir, ABS pump, third chassis brace, rear wing and brackets

Scratch-built: roll bar, pocket for brake master cylinder et al., oil filler and dipstick tubes, chassis braces (front), rear wing mechanism and body fill panel for the wing

Below is the completed model with the last picture of the AMG alongside last year's entry.

Thank you for looking and critiques are always welcome!

 

Your builds are always so tidy, I wish I could build half as cleanly.

[slusher]

12 hours ago, White Rabbit said:

2016 AMG GT

My completed entry for this year’s Cannonball.

 

Overview

The idea for this year’s entry was to have a true GT car that, as Jeremy Clarkson once said, is capable of traversing long distances at a high rate of speed in complete comfort. Therefore, a GT car built for the Autobahn seemed like a good choice as it’s made to cruise comfortably at 150mph all day.

The car itself has some modifications, the most visible being the Vossen MX-2 wheels (20”F, 21”R) wrapped in Continental Extreme Contact tires. Both were modeled and printed. Furthermore, the rear wing was cutout and modeled and printed as well, with its respective brackets so that it could be posed in its open position.

The interior has Recaro sport seats with a 4-point roll bar just behind. The interior is fully flocked.

The exterior was painted in Tamiya Bright Gunmetal Semi-gloss, which is analogous to Mercedes’ Selenite Grey semi-gloss. The interior is sky grey and black with the roll bar in body color. Finally, for an accent, the wheels are titanium gold in front of black brake calipers.

The engine was built from the kit, but detailed with wiring and plumbing. The under-hood molded-in hoses were cutout and replaced with aftermarket hoses and wiring. The molded-in brake master cylinder/booster/reservoir and ABS pump were also removed. In their place is modeled and printed versions the have been wired and plumbed. The bracing that runs from the firewall to the fenders was also scratch-built and added.

 

Specifications

Kit: Revell 2016 AMG GT

Exterior Paint: Tamiya Bright Gunmetal, semi-gloss black

Aftermarket: HobbyDesign detail set (photo-etch and resin) and resin Recaro seats, various wires and hoses from Detail Master and Gofer racing, Evergreen and Plastruct plastic stock

3D Print: wheels and tires, brake master cylinder/booster/reservoir, ABS pump, third chassis brace, rear wing and brackets

Scratch-built: roll bar, pocket for brake master cylinder et al., oil filler and dipstick tubes, chassis braces (front), rear wing mechanism and body fill panel for the wing

Below is the completed model with the last picture of the AMG alongside last year's entry.

Thank you for looking and critiques are always welcome!

 

Beautiful pair!

[White Rabbit]

9 hours ago, slusher said:

Beautiful pair!

 

20 hours ago, Fat Brian said:

Your builds are always so tidy, I wish I could build half as cleanly.

Thank you!

[White Rabbit]

Thus far, we have eight completed builds. There are still just over two weeks to go!

Updated List

Entry List

1. '56 Chevy (426 pack)

2. Chevy Chevelle (Mattilacken)⏸️

3. Porsche 918 Spyder (MeatMan)

4. '37 Ford Custom Convertible (Jantrix)

5. '16 Mercedes AMG GT (White Rabbit) 🏁

6. Dodge Viper RT/10 (LL3 Model Worx)

7. '70 Plymouth Road Runner (KWT)🏁

8. '66 Shelby GT350 Convertible (Fat Brian)🏁

9. '68 FRC Chevy Corvette (Whosurdaddy209)

10. '66 Mercury (Sam I Am)🏁

11. '70 1/2 Camaro Z28 or '67 Streaker Vette (JerseeJerry55)

12A. '71 Plymouth GTX (Keef)🏁

12B. Shelby Mustang (Keef)

13. Dodge L-xxx (vekasiini)

14. Honda Accord (Spottedlaurel)

15. Volkswagen Scirocco (Tim08)

16. Chevy Nova SS (53gmc)

17. '62 Buick Electra (Belugawrx)

18. Pontiac Firebird (Beans)

19. El Camino Camper (shoemake)

20. '53 Ford Victoria (Phildauplo)🏁

21. Nissan Skyline NISMO R34 GT-R (Jhedir6)

22. '54 Corvette (kermn8r)

23. '81 Chevy Citation (Westrods)

24. Toyota Supra (JerseeJerry55)

25. Ford Ranchero (Canso65)

26. '77 Chevy Malibu (Cheyenne93)

27. '66 Volkswagen Beetle (Tim H)

28. '51 Chevy Bel Air (landman)🏁

29. '01 Corvette Coupe (SmallRed63)

30. Fox Body Mustang GT (Dominik)

31. '40 Ford Pickup (Pat Minarick)

32. '65 Ford Galaxie X (Koellefornia)🏁

33. '69 Chevy Camaro (Disconovaman)

34. '70 Pontiac Firebird (bill_67)

Edited November 13, 2023 by White Rabbit