Exotics_Builder Posted April 8, 2023 Share Posted April 8, 2023 A bunch of things in the last couple of months have impeded progress on my builds. I started dinking with this about 2 years back and then put it on the shelf. The resin model is a Juha Airio design cast by Replicas and Miniatures of Maryland. I pulled it off again late last year. I’ve got the body almost totally cleaned up. Need to do some another round of primer and base white. Chassis work in progress. Adding disc brakes all around and Off the Sprue wheels adapted to some Revell big and little tires. Made a couple of mods to the interior, including some door card mods for eventual wood trim (decals from the parts box). Working on the engine as well. Detailing is about halfway done. The kit is prepped for a Big Block Chevy from the AMT 68 El Camino as well as suspension pieces. I decided to keep it that way. Color will be Testors Lacquer Inca Gold. 3 Quote Link to comment Share on other sites More sharing options...
SpikeSchumacher Posted April 8, 2023 Share Posted April 8, 2023 Wow, this is going to be cool! 1 Quote Link to comment Share on other sites More sharing options...
Paul Payne Posted April 9, 2023 Share Posted April 9, 2023 Looking forward to more! Looks great so far! 1 Quote Link to comment Share on other sites More sharing options...
Zippi Posted April 9, 2023 Share Posted April 9, 2023 I'm liking this one. Looking good so far. 1 Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted May 11, 2023 Author Share Posted May 11, 2023 Well, late on the updates. Components coming together, slowly. Got a booger in the hood and had to sand, primer and again paint. The interior is just about done. Added some Evergreen half round on the door cards and then some wood decals for extra visual effect (although hardly visible). Also added same wood decals on the dashboard plus BMF for the vents. Engine is wired up and finally set into the chassis. Added dip sticks for engine and transmission oil and some other wiring bits. Still need to run the brake and fuel line to their spots and finish that up. Wheels are set except for air valves (I do those last). Lots of finicky components left to sort out and install. Also, need to do a little more whittling to get the interior to fit. Initial test fit seemed good, but there is some gap up front that needs to be addressed. Given where I’m at, I don’t think it will be finished for our show on May 20, but should be ready for GoodGuys Puyallup. 4 Quote Link to comment Share on other sites More sharing options...
slusher Posted May 11, 2023 Share Posted May 11, 2023 Great looking seats! Real nice color choices, inside and out! 1 Quote Link to comment Share on other sites More sharing options...
bisc63 Posted May 11, 2023 Share Posted May 11, 2023 Very cool color combo. Stylish ride! 1 Quote Link to comment Share on other sites More sharing options...
ncbuckeye67 Posted May 11, 2023 Share Posted May 11, 2023 That looks amazing! The color is perfect for this build. Is that embossing powder carpet? I'm jealous of the precision and the crisp lines. My carpet never seems to look that good, no matter what I use. 1 Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted May 11, 2023 Author Share Posted May 11, 2023 8 hours ago, slusher said: Great looking seats! Real nice color choices, inside and out! All of that except for the wood trim and extra detail on the doors is from the kit. I've had it on the shelf for years and decided to tackle it. 3 hours ago, ncbuckeye67 said: That looks amazing! The color is perfect for this build. Is that embossing powder carpet? I'm jealous of the precision and the crisp lines. My carpet never seems to look that good, no matter what I use. I use different techniques for carpeting, depending on effect I want and visibility. In this case I used Rustoleum Textured finish paint on areas where I didn't mask off. Quote Link to comment Share on other sites More sharing options...
ncbuckeye67 Posted May 12, 2023 Share Posted May 12, 2023 I may have to try that. I have a can that I used to simulate an epoxy floor, for my garage diorama. I can always spray another color over it, to match the interior. I could tell you masked off certain areas, by how sharp and crisp the lines are. Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted May 12, 2023 Author Share Posted May 12, 2023 4 hours ago, ncbuckeye67 said: I may have to try that. I have a can that I used to simulate an epoxy floor, for my garage diorama. I can always spray another color over it, to match the interior. I could tell you masked off certain areas, by how sharp and crisp the lines are. I use Tamiya or Orlee masking tape. In this case, Tamiya. 1 Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted June 26, 2023 Author Share Posted June 26, 2023 As far as I can go on the frame until the "marriage". Need to get the interior and underside in place before mounting the frame to tie in the hoses and wheels. Getting closer. 2 Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted November 2, 2023 Author Share Posted November 2, 2023 Update 11-02-2023. Got back at this one as the clearcoat process on the 57 Crew Cab Car Hauler progresses. There's a scratch in the hood that requires a touch up of color coat and then clear. I cut out the front and rear windows using thesupplied templates and acetate sheet. They glue in from the outside, so a bit finicky. Then I glued in the lamps (front/rear), interior tub and lower body piece. Getting the frame ready to attach. I will then finish off the engine compartment, do a fina polish and add the remaining finicky bits like side view mirrors. Wheels are 3D prints from Off the Sprue. Detailed them out and need to air air valves (usually do as one of the last steps). Been a fun build thus far. 5 Quote Link to comment Share on other sites More sharing options...
Roadrunner Posted November 4, 2023 Share Posted November 4, 2023 I love that carpet. Quote Link to comment Share on other sites More sharing options...
BKIN10SECS Posted November 4, 2023 Share Posted November 4, 2023 7 hours ago, Roadrunner said: I love that carpet. I'm with you on that one! 1 Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted December 14, 2023 Author Share Posted December 14, 2023 Getting close to final assembly. Got the valve stems on the wheels and they're just waiting to be glued on. Most of the engine bay add-on's are done. I ran the heater and A/C lines, fabricated a radiator, and added the hoses. Remaining are the proportioning valve and brake lines. This has been a "fun" experience, because the body/chassis/frame had to be assembled to finish off. So protecting the finish is critical. The fuel and brake lines are done and the only item left on the chassis is add the wheels. Final fitment steps will be cleanup, adding mirrors and wipers and final polish. 4 Quote Link to comment Share on other sites More sharing options...
redscampi Posted December 14, 2023 Share Posted December 14, 2023 Man that is cool! 😎 1 Quote Link to comment Share on other sites More sharing options...
TransAmMike Posted December 14, 2023 Share Posted December 14, 2023 Wow Gerry, that's one cool Ford, looking forward to the completed pics!! 1 Quote Link to comment Share on other sites More sharing options...
Kit Karson Posted December 15, 2023 Share Posted December 15, 2023 You've come a long way, Baby! Way K😎L, Brother!! -KK 1 Quote Link to comment Share on other sites More sharing options...
slusher Posted December 16, 2023 Share Posted December 16, 2023 Looking great Gerry! 1 Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted December 17, 2023 Author Share Posted December 17, 2023 On 12/15/2023 at 10:57 AM, Kit Karson said: You've come a long way, Baby! Way K😎L, Brother!! -KK It has been 30 years since you convinced me to expand beyond foreign and exotics and do other car types. Remember that AMT 57 custom at Seattle Autorama? Quote Link to comment Share on other sites More sharing options...
Paul Payne Posted December 17, 2023 Share Posted December 17, 2023 Just Great! 1 Quote Link to comment Share on other sites More sharing options...
louis Carabott Posted December 22, 2023 Share Posted December 22, 2023 lovely work 1 Quote Link to comment Share on other sites More sharing options...
Exotics_Builder Posted December 31, 2023 Author Share Posted December 31, 2023 Still need to do final polish and a couple of tweaks. Will take some better photos mid-week and post in finished. Happy New Year all!! 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.