crowe-t Posted March 14 Share Posted March 14 (edited) I'm attempting to scratch build an International Harvester Metro Mite in 1/25 scale. A Metro Mite was used in the 1985 NBC TV series, Misfits Of Science as an Ice Cream truck. This is the version I want to build. The show is a favorite of mine. I picked up a Metro Mite Brochure on E-bay that had the specs and dimensional drawings. I started cutting out the sides using .060"(1.5mm) sheet styrene. The lower sides angle out so I'm experimenting with ways to replicate it. I would like to make the rear door roll up and I'm considering making the side doors slide open. However the doors curve out below the windows and I'd have to make the lower sides of the body curve out not only on the outside but the inside as well. The ice cream truck was only seen with the side doors closed in 2 shots in the pilot episode and the rest of the time they were open so I'm considering just making them in a fixed open position. This would solve some problems and make it easier. In the pilot the freezer unit on the roof was taller than the rest of the series so I might make it removable so I can use both. Does anyone have ideas on how to make the angled out lower body/sliding doors? I posted pictures of one test I did for the lower body. It will require cutting out the lower part of the side wall and gluing in the angled section. Another option would be to add an angled section on top of the side wall using thinner sheet styrene than I have in the picture. I appreciate any ideas and/or comments anyone can share. Thanks, Michael. Edited March 14 by crowe-t 1 Quote Link to comment Share on other sites More sharing options...
NOBLNG Posted March 14 Share Posted March 14 Hi Michael. Interesting project.😎 Maybe you could make the panels from 3 or more pieces laminated something like this? Good luck with it!🙂 Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 15 Author Share Posted March 15 6 hours ago, NOBLNG said: Hi Michael. Interesting project.😎 Maybe you could make the panels from 3 or more pieces laminated something like this? Good luck with it!🙂 Greg, Thanks for the drawing. I'm still brainstorming on this one. So far I'm liking what I came up with. I just have to test a few more ideas out. Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 21 Author Share Posted March 21 I got some more work done on this. I used the angled side pieces I put together. Today I started on the floor. Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 22 Author Share Posted March 22 Some more work on the floor. 1 Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 27 Author Share Posted March 27 Work continues on the floor. I made the doghouse using measurements a member of a group on Facebook sent me. To get the angle of the floor under the doghouse I placed the doghouse upside down under the floor after I glued it in place. It worked well. I then held the doghouse in place to support the firewall while the glue dried. I'll add the extended floor under the doghouse which is for the in line 6 cylinder engine I'm using. The 8 cylinder option had a shorter doghouse and didn't have the floor extension. 2 Quote Link to comment Share on other sites More sharing options...
CabDriver Posted March 27 Share Posted March 27 You’re doing an amazing job of scratchbuilding this - nice work!! Keep going! Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 27 Author Share Posted March 27 56 minutes ago, CabDriver said: You’re doing an amazing job of scratchbuilding this - nice work!! Keep going! Thanks Jim. Quote Link to comment Share on other sites More sharing options...
Jonathan Posted March 27 Share Posted March 27 Really enjoying seeing this. Nice work so far! Quote Link to comment Share on other sites More sharing options...
TarheelRick Posted March 27 Share Posted March 27 Always enjoy someone using their imagination to build something out of the ordinary. Your work is right on target. You mentioned an in-line 6, what chassis and other drivetrain are you using? Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 27 Author Share Posted March 27 3 hours ago, Jonathan said: Really enjoying seeing this. Nice work so far! Thanks Jonathan. Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 27 Author Share Posted March 27 13 minutes ago, TarheelRick said: Always enjoy someone using their imagination to build something out of the ordinary. Your work is right on target. You mentioned an in-line 6, what chassis and other drivetrain are you using? I saw a 1971 Metro Mite on YouTube that has an AMC in line 6. I ordered an AMT AMC Pacer Wagon kit for the in line 6. I had also bought an AMT International Scout II kit but the chassis is not the same. A member of a group on Facebook took measurements and sent me pictures of part of the chassis rails he took out of his Metro Mite. It's unibody but does have chassis rails welded to the floor. The chassis rails are channeled on the inside so I ordered some Evergreen channels that I'll use for the rails. Unless I can find a front axle I'll just scratch build one. These had a straight front axle with leaf springs. For the rear end I might use one from an AMT Ford Econoline van. It seems to be the right width and looks close to the one in the AMT Scout II kit which is a bit shorter. I have some small pictures showing the chassis/underside of a Metro Mite I found online. I'll do the best I can to make it look correct. There's not a lot of information on these. Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 27 Author Share Posted March 27 (edited) I have to figure out what to use for the window glass. I have acetate but it's not stiff enough for the large front windows. I also have some Evergreen clear sheet styrene but it has a texture on it. Maybe Plastruct or another brand has clear sheet styrene that's smooth. Edited March 27 by crowe-t Quote Link to comment Share on other sites More sharing options...
hct728(Bob) Posted March 27 Share Posted March 27 (edited) 4 hours ago, crowe-t said: I have to figure out what to use for the window glass. I have acetate but it's not stiff enough for the large front windows. I also have some Evergreen clear sheet styrene but it has a texture on it. Maybe Plastruct or another brand has clear sheet styrene that's smooth. Plastruct clear sheet copolyester a.k.a. PET-G is used by many modelers, clearer than styrene. Glue it in with flexible white glue. Can be heat molded too. Love your project, looks neatly done, the cuts are straight and accurate Edited March 27 by hct728(Bob) 1 Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 27 Author Share Posted March 27 2 hours ago, hct728(Bob) said: Plastruct clear sheet copolyester a.k.a. PET-G is used by many modelers, clearer than styrene. Glue it in with flexible white glue. Can be heat molded too. Love your project, looks neatly done, the cuts are straight and accurate Thanks Bob. Quote Link to comment Share on other sites More sharing options...
crowe-t Posted March 27 Author Share Posted March 27 Today I added the floor extension under the rear of the doghouse. 1 Quote Link to comment Share on other sites More sharing options...
crowe-t Posted April 18 Author Share Posted April 18 (edited) I got some more work done on the Metro Mite. The doghouse is glued in and I cut out the floor for the engine. I added 1mm sheet styrene that I filed at a slight angle to the fenders. I'll add some putty to the fenders and angle it some more. The front of the floor/firewall area is angled in a bit and I started cutting out the wheel openings in the fenders and quarter panels. Edited April 18 by crowe-t 1 Quote Link to comment Share on other sites More sharing options...
1930fordpickup Posted Monday at 04:29 AM Share Posted Monday at 04:29 AM This is very nice. Great topic for a scratch build. For the front glass some people have used a 2 liter bottle. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.